Extron electronic RSB 126, RSF123 Front Panel Features, Operations, Powering on the switcher

Page 17

Operation

Front Panel Features

1

2

3

4

ACTIVE USB

EXEC

 

 

1

2

 

 

INPUT

 

MODE

1

2

 

 

 

 

1 2 3 4

OUTPUT

SW2 USB

USB SWITCHER

Active USB LEDs:

D

Input LEDs — Each of these LEDs lights when a host or PC is

 

connected to the switcher’s corresponding USB input port and

 

is detected by the SW USB, regardless of whether the input is

 

currently selected.

E

Output LEDs — Each of these LEDs lights when a peripheral

 

device is connected to the switcher’s corresponding output port

 

and has been enabled by the selected input device or host PC.

Operations

SW2 USB front panel

1

2

3

EXEC

MODE

123

4

5

4

ACTIVE USB

1 2 3 4

INPUT

1 2 3 4

OUTPUT

SW4 USB

USB SWITCHER

Powering on the switcher

To power on the SW USB,

1. Connect all input and output devices to the switcher’s rear panel connectors and, if desired, connect a host PC to the RS-232 port. (See chapter 2, “Installation,” for information on the rear panel connections.)

2. Plug the power supply into the two-pole captive screw power connector on the rear panel.

The unit performs a self-test, during which the Exec Mode LED and the front panel Input LEDs each blink once in sequence from left to right. If the self-test completes with no errors, the LED for the most recently selected input

5

SW4 USB and SW4 USB Plus front panel

A Power LED — This LED lights when the SW USB has power.

B

Exec Mode LED — This LED lights when the SW USB is in

 

executive mode, indicating that the front panel is locked and

 

commands cannot be entered through it.

C

Input Selection buttons and LEDs — Press these buttons

 

to select inputs 1 and 2 (SW2) or 1 through 4 (SW4 and

 

SW4 Plus). The LED at the right of each button lights when the

 

corresponding input has been selected.

 

These buttons also can be used to initiate executive mode and

 

to reset the unit. See “Enabling front panel lockout (executive

 

mode)” and “Resetting,” later in this chapter.

remains lit.

3. Select input 1, and power up the PC connected to input 1.

4. Repeat step 3 for all remaining inputs to which PCs are connected.

Selecting an input

SW USB inputs can be selected by using:

•The front panel buttons

•Contact closure

•SIS commands

Selecting an input from the front panel

To select an input from the front panel, press the desired input’s button. The LED corresponding to the selected input button lights.

After an input is selected, the LED remains lit until a new input is selected.

3-2

SW USB Series • Operation

SW USB Series • Operation

3-3

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SW USB Series Extron’s Warranty PrecautionsFCC Class a Notice 安全须知 中文Step Quick Start Guide SW USB SeriesTable of Contents One Table of Contents, cont’dIntroduction SW USB SeriesIntroduction FeaturesAbout this Manual About the SW USB SeriesSW4 USB Introduction, cont’d Application DiagramsTwo InstallationSW USB Series Introduction, cont’dInstallation Overview InstallationMounting the SW USB Series Switcher Tabletop useFurniture mounting Installation, cont’dRack mounting procedure Preparing the SW USB for under-desk mounting Rear Panel FeaturesSW2 USB rear panel SW4 USB rear panelPower connector wiring Wiring the Power ConnectorRS-232 connector pin assignments Installation, cont’d Wiring for RS-232 CommunicationRS-232 port RS-232 Pass Thru portControlling an Extron A/V switcher in Loop 0 mode Connecting Multiple SW USB Switchers in a SystemContact Closure Control Connections for RS-232 loop-throughOperation ThreePowering on the switcher Front Panel FeaturesOperation OperationsSelecting an input using SIS commands Selecting an input using contact closureMode SIS commands issued via SIS command to enable Loop SIS command processing in Loop 1 modeSW USB Function SW USB Response to Host Command Enabling front panel lockout executive modeSending commands to an A/V switcher using contact closure Contact closure SIS command sent Function on SelectionSetting executive mode ResettingSetting up for host emulation Host emulation SW4 USB Plus onlyTroubleshooting SIS Configuration and ControlFour Peripheral emulation SW4 USB Plus onlyUsing the Command/Response Table SIS Configuration and ControlHost-to-Switcher Communications SW USB Series SIS Configuration SIS Configuration and Control, cont’dCommand/response table for SIS commands Downloading and installing the SW USB firmware SIS Configuration and Control, cont’d Updating the FirmwareDownloading and installing the Firmware Loader Loading the firmware to the SW USB using the Firmware Loader Problem solving AAppendix a Specifications, Part Numbers AccessoriesSpecifications Specifications, Part Numbers, AccessoriesMounting options AccessoriesOptional accessories Specifications, Part Numbers, Accessories, cont’d

SW USB Series, RSB 126, RSU 126, RSB129, RSF123 specifications

Extron Electronic is a well-known brand in the AV industry, renowned for its high-quality signal distribution, control systems, and mounting solutions. Among its impressive range of products, the RSB129, RSF123, RSU 126, RSB 126, and SW USB Series stand out due to their sophisticated features and technologies.

The RSB129 is a robust rack shelf designed to accommodate a variety of equipment, such as routers, switches, and other AV devices. This shelf can support up to 300 pounds, making it an excellent choice for heavy-duty applications. It also features adjustable mounting points that allow for flexible placement of devices, ensuring an organized and efficient setup.

The RSF123, on the other hand, is a flexible rack frame solution that provides a reliable mounting option for intermediate size equipment. This 2U rack frame is built to hold devices securely, while its front ventilation design aids in maintaining optimal temperature levels. The RSF123 is particularly popular for those looking to streamline their installations with a clean and professional aesthetic.

The RSU 126 is another versatile rack mount solution that focuses on aesthetic appeal while providing functionality. Designed for environments where aesthetics matter, the RSU 126 features a smooth, sleek design that integrates seamlessly into office and conference room settings. Its compact 2U size makes it suitable for various AV applications, while its durable build ensures long-lasting use.

The RSB 126 is similar in nature to the RSB129 but is crafted for smaller setups. This 1U rack shelf is ideal for less intensive applications but still boasts impressive weight support. It features a front lip that prevents equipment from sliding off, ensuring that devices are kept securely in place. The RSB 126 is perfect for studios, server rooms, or any location requiring a compact yet sturdy shelf.

Finally, the SW USB Series is a suite of USB products designed to streamline connectivity in modern AV installations. These USB devices offer flexible options for extending USB signals over long distances without loss of quality. They support a variety of USB protocols, making them compatible with numerous devices, from cameras to computers. The SW USB Series aims to simplify complex installations, ensuring a reliable connection in various environments.

In summary, Extron's RSB129, RSF123, RSU 126, RSB 126, and SW USB Series products cater to a variety of AV installation needs, combining durability, functionality, and aesthetics. Whether for heavy-duty rack shelving or streamlined USB connectivity, these products are designed to enhance any AV setup.
Top Page Image Contents