Extron electronic RSF123 Resetting, Host emulation SW4 USB Plus only, Setting executive mode

Page 20

Operation, cont’d

1 2

 

EXEC

Release buttons.

MODE

Exec Mode

Press and hold simultaneouslyLED lights. for 5 seconds.

Setting executive mode

To exit executive mode, repeat the procedure described on the previous page. When the SW USB is no longer in executive mode, the red LED turns off.

2. Place the DIP switches on the rear panel in the appropriate position to enable emulation for the connected device. The table below shows the switch positions for keyboard and/or mouse emulation.

Switch 1

Switch 2

Emulation

(Mouse)

(Keyboard)

 

Off (down)

Off (down)

No emulation

 

 

 

On (up)

Off (down)

Emulate mouse only

 

 

 

Off (down)

On (up)

Emulate keyboard only

 

 

 

On (up)

On (up)

Emulate keyboard and

 

 

mouse

Resetting

To reset the switcher to its factory default settings from the front panel,

1. Disconnect power from the SW USB.

2. Press and hold the Input 1 button while applying power to the unit.

Example: In the illustration at right, emulation is enabled for both a mouse and a keyboard.

If two standard mice or keyboards are connected to output ports 3 and 4, and the appropriate emulation DIP switch is set to on (up), the SW4 USB Plus emulates a host to both ports.

MOUSE

ON ON

OFF 1 2

KEYBOARD

The Input LEDs blink three times to indicate that a reset has occurred. The input selection defaults to input 1, and the Input 1 LED lights.

Host emulation (SW4 USB Plus only)

The SW4 USB Plus model provides host emulation to peripheral devices on the output of the switcher. If a keyboard and/

or a mouse is connected to output port 3 or 4, and the Host Emulation DIP switch(es) are set to on, the SW USB emulates a host PC to the connected peripheral device. The keyboard/ mouse connected to the switcher’s port 3 or 4 still responds as if it were attached directly to the computer on the selected input.

Host emulation allows instant communication of the emulated ports when the SW USB switches to another input, by eliminating the delay that normally occurs when a computer recognizes a new device.

Setting up for host emulation

Host emulation is enabled via the Host Emulation DIP switches on the rear panel. To enable host emulation,

1. Connect a keyboard, a mouse, or both to output port 3 and/or 4. The SW4 USB Plus can emulate a keyboard and a mouse simultaneously. Either type of device can be connected to either or both of the two emulation ports (3 and 4).

NWhen one or both DIP switches are set to on (up), host emulation follows the attached peripheral device:

•When the Mouse DIP switch (switch 1) is set to on (up), the switcher emulates a host to any standard mouse that is connected to either of the emulation output ports (3 or 4).

•When the Keyboard DIP switch (switch 2) is set to on, the switcher emulates a host to any standard keyboard that is connected to an emulation port.

•When both DIP switches are set to on, the switcher emulates a host to any connected standard mouse and/or keyboard that is connected to port 3 or 4.

Supported peripheral devices

The SW4 USB Plus can emulate a host only to a standard keyboard and a standard mouse. The emulation feature is not supported with non-standard keyboards or mice, such as devices that require additional drivers.

USB devices other than standard keyboards and mice can be connected to output ports 3 and 4, but are not supported by the emulation feature. If you plan to use such devices, set the Host Emulation DIP switches to off. Examples of non-standard keyboards or mice include media keyboards or five-button mice.

3-8

SW USB Series • Operation

SW USB Series • Operation

3-9

Page 19 Page 21
Image 20
Page 19 Page 21
Contents SW USB Series Precautions Extron’s Warranty安全须知 中文 FCC Class a NoticeQuick Start Guide SW USB Series StepTable of Contents Table of Contents, cont’d OneIntroduction SW USB SeriesFeatures IntroductionAbout this Manual About the SW USB SeriesIntroduction, cont’d Application Diagrams SW4 USBInstallation TwoSW USB Series Introduction, cont’dInstallation Installation OverviewMounting the SW USB Series Switcher Tabletop useFurniture mounting Installation, cont’dRack mounting procedure Rear Panel Features Preparing the SW USB for under-desk mountingSW2 USB rear panel SW4 USB rear panelWiring the Power Connector Power connector wiringInstallation, cont’d Wiring for RS-232 Communication RS-232 connector pin assignmentsRS-232 port RS-232 Pass Thru portConnecting Multiple SW USB Switchers in a System Controlling an Extron A/V switcher in Loop 0 modeContact Closure Control Connections for RS-232 loop-throughThree OperationFront Panel Features Powering on the switcherOperation OperationsSelecting an input using contact closure Selecting an input using SIS commandsMode SIS commands issued via SIS command to enable Loop SIS command processing in Loop 1 modeEnabling front panel lockout executive mode SW USB Function SW USB Response to Host CommandSending commands to an A/V switcher using contact closure Contact closure SIS command sent Function on SelectionResetting Setting executive modeSetting up for host emulation Host emulation SW4 USB Plus onlySIS Configuration and Control TroubleshootingFour Peripheral emulation SW4 USB Plus onlyUsing the Command/Response Table SIS Configuration and ControlHost-to-Switcher Communications SW USB Series SIS Configuration SIS Configuration and Control, cont’dCommand/response table for SIS commands Downloading and installing the SW USB firmware SIS Configuration and Control, cont’d Updating the FirmwareDownloading and installing the Firmware Loader Loading the firmware to the SW USB using the Firmware Loader Problem solving Specifications, Part Numbers Accessories AAppendix aSpecifications, Part Numbers, Accessories SpecificationsMounting options AccessoriesOptional accessories Specifications, Part Numbers, Accessories, cont’d

SW USB Series, RSB 126, RSU 126, RSB129, RSF123 specifications

Extron Electronic is a well-known brand in the AV industry, renowned for its high-quality signal distribution, control systems, and mounting solutions. Among its impressive range of products, the RSB129, RSF123, RSU 126, RSB 126, and SW USB Series stand out due to their sophisticated features and technologies.

The RSB129 is a robust rack shelf designed to accommodate a variety of equipment, such as routers, switches, and other AV devices. This shelf can support up to 300 pounds, making it an excellent choice for heavy-duty applications. It also features adjustable mounting points that allow for flexible placement of devices, ensuring an organized and efficient setup.

The RSF123, on the other hand, is a flexible rack frame solution that provides a reliable mounting option for intermediate size equipment. This 2U rack frame is built to hold devices securely, while its front ventilation design aids in maintaining optimal temperature levels. The RSF123 is particularly popular for those looking to streamline their installations with a clean and professional aesthetic.

The RSU 126 is another versatile rack mount solution that focuses on aesthetic appeal while providing functionality. Designed for environments where aesthetics matter, the RSU 126 features a smooth, sleek design that integrates seamlessly into office and conference room settings. Its compact 2U size makes it suitable for various AV applications, while its durable build ensures long-lasting use.

The RSB 126 is similar in nature to the RSB129 but is crafted for smaller setups. This 1U rack shelf is ideal for less intensive applications but still boasts impressive weight support. It features a front lip that prevents equipment from sliding off, ensuring that devices are kept securely in place. The RSB 126 is perfect for studios, server rooms, or any location requiring a compact yet sturdy shelf.

Finally, the SW USB Series is a suite of USB products designed to streamline connectivity in modern AV installations. These USB devices offer flexible options for extending USB signals over long distances without loss of quality. They support a variety of USB protocols, making them compatible with numerous devices, from cameras to computers. The SW USB Series aims to simplify complex installations, ensuring a reliable connection in various environments.

In summary, Extron's RSB129, RSF123, RSU 126, RSB 126, and SW USB Series products cater to a variety of AV installation needs, combining durability, functionality, and aesthetics. Whether for heavy-duty rack shelving or streamlined USB connectivity, these products are designed to enhance any AV setup.
Top Page Image Contents