3M 39600 manual Maintenance, Lubrication

Page 27

Maintenance

The case sealer has been designed for long, trouble free service. The machine will perform best when it receives routine maintenance and cleaning.

Machine components that fail or wear excessively should be promptly repaired or replaced to prevent damage to other portions of the machine or to the product.

WARNING – Turn off electrical power and air supply and

disconnect power cord from electrical supply before beginning maintenance. If electrical power is not disconnected, severe injury to personnel could result.

Cleaning

Note –Never attempt to remove dirt from the machine by blowing it out with compressed air. This can cause the dirt to be blown inside the motor and onto sliding surfaces which may cause premature equipment wear. Never wash down or subject equipment to conditions causing moisture condensation on components. Serious equipment damage could result.

Regular slotted containers produce a great deal of dust and paper chips when processed or handled in equipment. If this dust is allowed to build-up on machine components, it can cause component wear and overheating of drive motor. The dust build-up can best be removed from the machine by a shop vacuum. Depending on the number and type of boxes sealed in the case sealer, this cleaning should be done approximately once per month. If the boxes sealed are dirty, or if the environment in which the machine operates is dusty, cleaning on a more frequent basis may be necessary. Excessive dirt build-up that cannot be removed by vacuuming should be wiped off with a damp cloth.

Lubrication

Most of the machine bearings, including the drive motor, are permanently lubricated and sealed and do not require additional lubricant.

Figure 4-1 illustrates the machine points that do require lubrication every 250 hours of operation.

Lubricate the points indicated by arrows ( ) with a small amount of multi-purpose grease.

Note –Wipe off excess oil and grease. It will attract dust which can cause premature equipment wear and jamming. Take care that oil and grease are not left on the surface of rollers around which tape is threaded, as it can contaminate the tape's adhesive.

TAPING HEAD LUBRICATION – See Section II, "Maintenance – Lubrication", page 10.

Figure 4-1 – Lubrication Points – Frame

22

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 3M-Matic To Our Customers Replacement Parts and Additional ManualsTo Our Customers Table of Contents Section II AccuGlide II STD 2 Inch Taping Heads Description Contents 700r Random Case Sealer Knife Warning Label Important SafeguardsPinch Point Caution Label Air Pressure Label 14 Tape Threading Label Specifications Box Weight and Size Capacities Box BoardMinimum Maximum Set-Up Recommendations Machine Dimensions MinimumInstallation and Set-Up Raising and latching upper drive assemblyReceiving And Handling 700r Frame Set-Up Infeed Conveyor UncratedMachine BED Height Bumper Supports 700r Case Sealer Components Left Front View OperationMain Air On/Off Valve/Pressure Regulator/ Filter -3 Controls, Valves and Switches Electrical On/Off SwitchRaising Switch, Upper Drive Assembly Emergency Stop SwitchMain Air Pressure Gauge Mechanical Latch, Upper Drive Assembly FigureSee Section II, Pages 7 Theory of Operation Box Centering SwitchDrive Belts Box SealingLubrication MaintenanceLower Drive Belt Replacement Personnel could result Box Drive Belt ReplacementPersonnel could result Circuit Breaker Knife Replacement, Taping HeadPersonnel could result Box Drive Belt Tension AdjustmentsPersonnel could result Box Drive Belt Tension Adjustment, Lower BeltsInfeed EndInjury to personnel could result This page is Blank Case Sealer Frame Changes Special Set-Up ProcedureRemove Upper Taping Head Box and Machine Bed Height Range Stop Bumpers Disconnected, severe injury to personnel could resultTroubleshooting Guide Problem Cause Correction TroubleshootingTroubleshooting Electrical Diagram Electrical DiagramPneumatic Diagram Pneumatic DiagramReplacement Parts And Service Information Part Number Option/Accessory Options/AccessoriesReplacement Parts Illustrations and Parts Lists This page is Blank 700r Random Case Sealer Frame Assemblies 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description Safety and Information Labels Ref. No 3M Part No Description Qty Safety and Information Labels
Related manuals
Manual 94 pages 44.17 Kb Manual 70 pages 21.44 Kb Manual 64 pages 55.71 Kb Manual 70 pages 16.15 Kb

39600 specifications

The 3M 39600 is a high-quality, versatile adhesive designed to meet the needs of professionals across various industries. This product is particularly well-regarded for its exceptional bonding capabilities and ease of use, making it a popular choice among contractors, automotive professionals, and DIY enthusiasts alike.

One of the main features of the 3M 39600 is its strong adhesion to a wide range of substrates. This includes metals, plastics, glass, and composites, allowing users to bond different materials seamlessly. The adhesive forms a strong, durable bond that provides long-lasting performance, making it suitable for both interior and exterior applications.

Another key characteristic of the 3M 39600 is its fast curing time. The adhesive typically sets quickly, which is crucial in fast-paced work environments where time is of the essence. This rapid curing allows users to proceed with their projects without long wait times. Additionally, the adhesive exhibits high resistance to moisture and temperature fluctuations, ensuring that the bond remains secure even in challenging environmental conditions.

The technology behind the 3M 39600 is based on advanced polymer chemistry, which contributes to its reliable performance. The formulation of the adhesive results in excellent shear strength and tensile strength, making it ideal for demanding applications. The product is also designed to be user-friendly; it can be applied using various methods such as brush, roller, or spray, depending on the specific requirements of the project.

3M 39600 is often recognized for its versatility. It is suitable for applications in industries like automotive, construction, electronics, and appliance manufacturing. In the automotive sector, for example, it is used for bonding parts together, ensuring structural integrity and enhancing both performance and aesthetics.

In summary, the 3M 39600 adhesive is a top choice for those seeking a reliable and efficient bonding solution. Its strong adhesion, fast curing time, and advanced technology make it suitable for a variety of applications. Whether you are a professional or a DIY enthusiast, the 3M 39600 provides the performance you need to achieve quality results in your projects.
Top Page Image Contents