3M 39600 manual Emergency Stop Switch, Raising Switch, Upper Drive Assembly

Page 22

Operation (Continued)

Pressure Regulator regulates main air pressure to the machine to adjust pressure, pull knob up and turn – push down to lock setting.

Filter removes dirt and moisture from plant air before it enters the case sealer pneumatic circuits. If water collects in bottom of bowl, lift up on the valve on the bottom of bowl to drain.

3Emergency Stop Switch

The machine electrical supply can be turned off by pressing the latching emergency stop switch. To restart machine, rotate emergency stop switch (releases switch latch) and then restart machine by pressing green (On) button on side of machine frame.

4Raising Switch, Upper Drive Assembly

This switch, when touched by the leading edge of a box , pneumatically raises the upper frame to allow insertion of the box under the drive belts. As the box moves under the switch, releasing it, the upper drive assembly descends on the box and the drive belts convey the box through the machine. When switch is actuated by hand, the upper drive assembly rises to its maximum height. Released, the upper drive assembly descends to its rest position.

5Centering Switch, Box Centering Guide This pneumatic switch controls the box centering guides. When switch is activated by a box entering the case sealer, the centering guides close (centering the box), and released (after box passes over switch), the guides open.

6Air Pressure Regulator, Centering Guide Force Adjustment –Figure3-4

This regulator is used to adjust centering guides according to weight of boxes. Pressure should be adequate to center boxes, but low enough to allow easy pushing of boxes under taping head. The regulator setting can be locked by tightening the phillips screw as shown.

7Air Pressure Regulator/Gauge, Top Drive Assembly Force Adjustment –Figure3-5 Set nominally to control "down" movement of top drive assembly and the pressure exerted against the box. The regulator setting is changed as necessary for the boxes being sealed to provide adequate drive belt pressure

Figure 3-4– Air Regulator, Centering Guides

Figure 3-5 – Air Regulator/Gauge, Top Drive Assembly

against the box to positively convey the boxes through the machine. If the boxes stop or hesitate while being conveyed, decrease the regulator pressure which will increase the drive belt force on the box for more friction between the box and drive belts. Adjust setting as necessary to get continuous movement of boxes through machine.

17

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 3M-Matic Replacement Parts and Additional Manuals To Our CustomersTo Our Customers Table of Contents Section II AccuGlide II STD 2 Inch Taping Heads Description Contents 700r Random Case Sealer Important Safeguards Knife Warning LabelPinch Point Caution Label Air Pressure Label 14 Tape Threading Label Specifications Box Board Box Weight and Size CapacitiesMinimum Maximum Machine Dimensions Minimum Set-Up RecommendationsRaising and latching upper drive assembly Installation and Set-UpReceiving And Handling 700r Frame Set-Up Uncrated Infeed ConveyorMachine BED Height Bumper Supports Operation 700r Case Sealer Components Left Front ViewControls, Valves and Switches Electrical On/Off Switch Main Air On/Off Valve/Pressure Regulator/ Filter -3Emergency Stop Switch Raising Switch, Upper Drive AssemblyMechanical Latch, Upper Drive Assembly Figure Main Air Pressure GaugeSee Section II, Pages 7 Box Centering Switch Theory of OperationBox Sealing Drive BeltsMaintenance LubricationPersonnel could result Box Drive Belt Replacement Lower Drive Belt ReplacementKnife Replacement, Taping Head Personnel could result Circuit BreakerAdjustments Personnel could result Box Drive Belt TensionBox Drive Belt Tension Adjustment, Lower BeltsInfeed End Personnel could resultInjury to personnel could result This page is Blank Special Set-Up Procedure Case Sealer Frame ChangesRemove Upper Taping Head Box and Machine Bed Height Range Disconnected, severe injury to personnel could result Stop BumpersTroubleshooting Troubleshooting Guide Problem Cause CorrectionTroubleshooting Electrical Diagram Electrical DiagramPneumatic Diagram Pneumatic DiagramReplacement Parts And Service Information Options/Accessories Part Number Option/AccessoryReplacement Parts Illustrations and Parts Lists This page is Blank 700r Random Case Sealer Frame Assemblies 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description Safety and Information Labels Safety and Information Labels Ref. No 3M Part No Description Qty
Related manuals
Manual 94 pages 44.17 Kb Manual 70 pages 21.44 Kb Manual 64 pages 55.71 Kb Manual 70 pages 16.15 Kb
Top Page Image Contents