3M 39600 manual Special Set-Up Procedure, Case Sealer Frame Changes

Page 34

Special Set-Up Procedure

WARNING – Turn off electrical power and air supply and disconnect power cord from electrical supply before beginning Special Set-Up Procedure. If power cord is not disconnected, severe

injury to personnel could result.

Changing the Tape Leg Length (From 70 to 50 mm [2-3/4 to 2 inch])

The following changes to the case sealer frame and upper/lower taping heads reduces the tape leg length to 50 mm [2 inch] and also allows the taping of boxes 95 mm [3.75 inch] minimum height.

CASE SEALER FRAME (Refer to Figure 6-1A)

1.Raise and latch upper drive assembly in upper position. Turn off air supply and electric power.

2.Remove and retain the screws, washers and bumper support assembly on both side columns. Remount and secure the bumper support assemblies using the top holes and original fasteners.

3.Be sure adjustable split collars on column cylinder rods are loose or clamped at the top of the cylinder rod to allow the upper drive assembly to descend fully.

Figure 6-1 – Case Sealer Frame Changes

29

Image 34

Contents 3M-Matic Replacement Parts and Additional Manuals To Our CustomersTo Our Customers Table of Contents Section II AccuGlide II STD 2 Inch Taping Heads Description Contents 700r Random Case Sealer Important Safeguards Knife Warning LabelPinch Point Caution Label Air Pressure Label 14 Tape Threading Label Specifications Box Board Box Weight and Size CapacitiesMinimum Maximum Machine Dimensions Minimum Set-Up RecommendationsRaising and latching upper drive assembly Installation and Set-UpReceiving And Handling 700r Frame Set-Up Uncrated Infeed ConveyorMachine BED Height Bumper Supports Operation 700r Case Sealer Components Left Front ViewControls, Valves and Switches Electrical On/Off Switch Main Air On/Off Valve/Pressure Regulator/ Filter -3Emergency Stop Switch Raising Switch, Upper Drive AssemblyMechanical Latch, Upper Drive Assembly Figure Main Air Pressure GaugeSee Section II, Pages 7 Box Centering Switch Theory of OperationBox Sealing Drive BeltsMaintenance LubricationPersonnel could result Box Drive Belt Replacement Lower Drive Belt ReplacementKnife Replacement, Taping Head Personnel could result Circuit BreakerAdjustments Personnel could result Box Drive Belt Tension Box Drive Belt Tension Adjustment, Lower BeltsInfeed End Personnel could resultInjury to personnel could result This page is Blank Special Set-Up Procedure Case Sealer Frame ChangesRemove Upper Taping Head Box and Machine Bed Height Range Disconnected, severe injury to personnel could result Stop BumpersTroubleshooting Troubleshooting Guide Problem Cause CorrectionTroubleshooting Electrical Diagram Electrical DiagramPneumatic Diagram Pneumatic DiagramReplacement Parts And Service Information Options/Accessories Part Number Option/AccessoryReplacement Parts Illustrations and Parts Lists This page is Blank 700r Random Case Sealer Frame Assemblies 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description 700r Random Case Sealer Ref. No 3M Part No Description Safety and Information Labels Safety and Information Labels Ref. No 3M Part No Description Qty

Related manuals

Manual 94 pages 44.17 Kb

Manual 70 pages 21.44 Kb

Manual 64 pages 55.71 Kb

Manual 70 pages 16.15 Kb