Miele G 5100, G 5105 manual Programming the water softener

Page 12

Before using for the first time

Programming the water softener

To exit the programming mode at any time turn the dishwasher off with the button.

Press the button to turn the dishwasher off.

Press and hold the "Start / Stop" button and turn the dishwasher on simultaneously using the button. Keep the "Start / Stop" button pressed for at least four seconds until the "Start / Stop" indicator light comes on.

If it does not come on, start over.

Now press the "Delay Start" button twice.

The characters "P 1 5" will flash one after the other in the display. This means that the water hardness elvel has been set at 15 °d [2.7 mmol/l (factory setting)].

The value which has been set for the water hardness is shown as a figure after the "P" in the display (see chart).

Use the "Start / Stop" button to select the flashing rhythm that corresponds to your water hardness level.

With each press of the button the value will raise one level. Once the highest value is reached the setting will start again from the beginning.

Press the button to turn the dishwasher off.

		Value
°d	gr/gal	displayed

1	1	1
2	2	2
3	3	3
4	4	4
5	5	5
6	6	6
7	7	7
8	8	8
9	9	9
10	10	10
11	11	11
12	13	12
13	14	13
14	15	14
15	16	15
16	17	16
17	18	17
18	19	18
19	20	19
20	21	20
21	22	21
22	23	22
23	24	23
24	25	24
25	26	25
26	27	26
27	28	27
28	29	28
29	30	29
30	31	30
31	32	31
32	33	32
33	34	33
34	35	34
35	36	35
36	38	36
37-50	39-52	50
51-60	53-63	60
61-70	64-73	70

12

Image 12

Contents

Operating Instructions Dishwasher 5100 G Contents Contents Electrical Safety Correct usageInstallation Use Disposal of an applianceGuide to the dishwasher Control panel Caring for the environment Energy saving washingBefore using for the first time To open the door Child safety lockTo close the door Water softener Programming the water softener Checking the programmed water hardness Filling the salt container Refill salt message Deactivate indicators Rinse aid Adding rinse aidRinse aid indicator Adjusting the dosage Loading the dishwasher Items not recommended for dishwashing GlasswareSilver and aluminum Typical load for 10 place settings Typical load for 16 place settings Adjustable cup rack Upper basketAdjusting the upper basket Lower basket Removable MultiComfort insert To remove the insertTo replace the insert Glass rackFoldable spikes Cutlery tray Cutlery basket Cutlery insert for the cutlery basketOptional accessories MieleCare CollectionUse DetergentUse Adding detergentProgress indicator Turning onSelecting a program Starting a programProgram When to use Program sequence Guide Program GuideStandby At the end of a programTurning off Preparing your appliance for an extended vacationUnloading the dishwasher Interrupting a programChanging a program Delay start Additional optionsTurbo Delay start display Starting a program before the Delay start has elapsedOptimize Standby Factory default Frequently asked questions Technical faultsProblems water Intake / Drain General problems with the dishwasher Sounds Poor cleaning results Problem Possible fault Solution Dishes are notClean GlassesProblem Possible fault Solution Dishes are not dry Cutlery areSpotted White residue isProblem Possible fault Solution Glasses have a Brown or blueDiscoloration film Cannot be wiped off Glasses are dull Discolored filmAfter sales service PC UpdateRepairs MieleCareTransport User Maintenance Instructions Cleaning and Care ExteriorWash cabinet Door and the door sealTriple filter system Cleaning and Care Cleaning the spray arms Removing the spray armsCleaning the drain pump and non-return valve Installation Instructions Help to protect the environment Disposal of the packing materialDisposal of an old machine Electrical connection Grounding InstructionsHardwired electrical connection Grounding Instructions This Appliance Must be GroundedPlumbing Connection to the water supplyDrainage Venting the drainage systemPage Alteration rights reserved Nr 016 310 G5100/G5105