Scotsman Ice MDT5N25, MDT5N40 Removal and Replacement, BIN Controls Ice Level Sensors

Page 24

MDT5N25 & MDT5N40

REMOVAL AND REPLACEMENT

WATER RESERVOIR

1.Shut off the water supply to the icemaker.

2.Remove front panel and reservoir cover.

3.Disconnect inlet water line from valve.

4.To remove just the float, push the locking tab at the back of the valve mounting block in and lift the valve and block up and out of the reservoir tank.

Note: inside the valve, there is a plunger which may be replaced separately, if desired.

5.To remove reservoir, remove drain hose from reservoir.

6.Remove evaporator inlet hose from reservoir.

7.Remove mounting screws from reservoir

bracket, and remove reservoir from icemaker.

8.Reverse to reassemble.

FLOAT VALVE

VALVE

PLUNGER

BIN CONTROLS (Ice Level Sensors)

1.Disconnect electrical power.

2.Remove front panel.

3.Remove control box cover.

4.Locate bin top, in front of and behind it are two rubber bin control grommets.

5.Pull each bin control out, and in the control box, disconnect the electrical leads connecting the bin control to the circuit board.

6.Reverse to reassemble, be certain that the bin controls are aligned so that the ice level sensors are visible (centered) through the holes in the ice chute.

BIN CONTROLS

GROMMETS

LOCKING TAB

BIN TOP

May 2001

Page 24

Image 24
Contents Table of Contents IntroductionMDT5N25 & MDT5N40 For the Installer Environmental Limitations Installation Limitations Service LimitationsMinimum Maximum Water LimitationsFor the Installer Machine Stand InstallationCounter Top or Machine Stand Installation Unpack and install the ice and water spoutsFor the Installer Wall Mount Kit For the Plumber Conform to ALL Applicable CodesFor the Electrician For the Installer Final Check List Initial Start UP Pre Start InspectionStart Up Component Description ICE Sweep Bearing Breaker Motor Evaporator Auger Water Seal On/Off Switch Manual Component Description Control BoxCircuit Board Potential RelaySplash panel cleaning Electrical SequenceStart up consists Shut Down consistsOperation Water Refrigeration Schematic Operation RefrigerationOperation Ice Vending ContainerDispense Area Sanitation Cleaning and Sanitizing Scotsman Ice Machine Cleaner contains acidsTo Sanitize Check and tighten all bolts and screws Maintenance and Cleaning Moving Parts HazardService Diagnosis Symptom Possible Cause Probable CorrectionMDT5N25 & MDT5N40 Service Diagnosis Circuit Board PowerOff Timer Bin EmptyRemoval and Replacement BIN Controls Ice Level SensorsRemoval and Replacement Bearing And Breaker To Remove the Breaker Bearing AssemblyTo Remove the Auger Removal and Replacement Water Seal To Remove the Water SealTo Replace the Water Seal For Access to the Evaporator to Gearmotor bolts To Replace the EvaporatorTo Reassemble the Evaporator and Auger To Remove and Repair the Gearmotor Assembly Electrical Shock HazardTo Inspect the gearmotor Refrigeration Service R-404A HP62 Do not USE Mineral OIL in this Refrigeration SystemRefrigeration Service General InformationOnly a HFC type dryer should be used Circuit Board Service Printed Circuit Board Handling PrecautionsLiquid Charging Instructions for R-404A

MDT5N40, MDT5N25 specifications

The Scotsman Ice MDT5N25 and MDT5N40 models are part of a sophisticated line of ice machines designed for commercial use. These models stand out for their efficiency, reliability, and advanced technology, making them ideal for restaurants, bars, and other food service establishments that require a constant supply of ice.

One of the main features of the Scotsman MDT5N25 and MDT5N40 models is their ability to produce high volumes of ice quickly while maintaining energy efficiency. These machines are designed to provide a steady supply of ice, ensuring that businesses can meet the demands of their customers without interruption. The MDT5N25 can produce approximately 260 pounds of ice per day, while the MDT5N40 takes it a step further by producing around 450 pounds daily. These capacities make both models suitable for various applications, from small cafes to larger dining venues.

Both models are equipped with Scotsman’s proprietary EcoX technology, which enhances energy efficiency and reduces water consumption. This technology employs advanced engineering designs that minimize waste and optimize production cycles. This focus on sustainability not only helps reduce operational costs but also appeals to environmentally conscious businesses.

The MDT5N25 and MDT5N40 also feature a self-cleaning mechanism that simplifies maintenance and ensures consistent ice quality. The automatic cleaning cycle helps prevent limescale and bacteria buildup, providing peace of mind for operators who prioritize hygiene and food safety.

In terms of design, both models boast a compact footprint, making them suitable for establishments with limited space. They come with a built-in storage bin that efficiently holds large quantities of ice, streamlining operations and making it easy for staff to access ice when needed. The sleek stainless steel finish of the machines not only enhances their durability but also ensures they can blend seamlessly into any commercial kitchen environment.

The user-friendly control panel on both the MDT5N25 and MDT5N40 allows for easy adjustments and monitoring of the machine’s performance. Operators can easily keep track of production levels and patterns, ensuring they can manage their ice supply effectively.

In conclusion, the Scotsman Ice MDT5N25 and MDT5N40 models represent a robust solution for commercial ice production, combining efficiency, advanced technology, and ease of use. With their impressive output capacities, energy-efficient designs, self-cleaning features, and durable construction, these machines are perfect for businesses that rely on consistent ice production to meet their needs.