Scotsman Ice MDT5N40, MDT5N25 service manual For the Installer Wall Mount Kit

Page 5

MDT5N25 & MDT5N40

FOR THE INSTALLER: Wall Mount Kit

CAUTION

It is recommended that the wall mounting

 

 

installation be done by an experienced contractor.

 

The weight of the machine when in use may

 

 

exceed 350 pounds. The unit should be mounted

 

on a solid, rigid wall with proper fasteners for that

 

type of wall and of adequate strength to support

 

the weight of the machine when in use.

 

 

Clearance between the wall and the icemaker is a

 

maximum of 1 inch. Check utility connections first.

 

The electrical junction box will have to be removed,

 

and the electrical connections made inside the

 

cabinet in compliance with local codes. The

 

 

plumbing connections may be made through the

 

base, or at either side through the pre-punched

 

holes, using standard plumbing practices.

 

 

Interior plumbing lines must be disconnected from

 

the original connections and plugged when

MDT6N40=38.6"

routing through the side or base.

 

MTD6N25=30"

1. Remove machine top. Attach bracket “A” to

 

machine using (3) nuts, (3) flat washers, (3) lock

 

washers, and (3) 5/16-18 bolts received with the

7.83

kit.

 

 

1" CLEARANCE

BASE SIDE

HOLE ROUTIN

16"

DO NOT LIFT ON SINK

 

16"A

2. Mount brackets “B” and “C” to the wall at the dimensions shown for the unit. (hardware for this is not included).

B

12"

12"

Use fasteners and wall of sufficient strength to carry the use and weight of the icemaker-dispenser.

3.Lift unit up and hook bracket “A” over bracket “B”. Slide unit until the two remaining holes are aligned and secure with the remaining (2) 1/4-20 bolts, flat washers and lock washers.

C

May 2001

Page 5

Image 5
Contents Introduction Table of ContentsMDT5N25 & MDT5N40 Installation Limitations Service Limitations For the Installer Environmental LimitationsMinimum Maximum Water LimitationsMachine Stand Installation For the InstallerCounter Top or Machine Stand Installation Unpack and install the ice and water spoutsFor the Installer Wall Mount Kit Conform to ALL Applicable Codes For the PlumberFor the Electrician For the Installer Final Check List Start Up Initial Start UPPre Start Inspection Component Description ICE Sweep Bearing Breaker Motor Evaporator Auger Water Seal Component Description Control Box On/Off Switch ManualCircuit Board Potential RelayElectrical Sequence Splash panel cleaningStart up consists Shut Down consistsOperation Water Operation Refrigeration Refrigeration SchematicContainer Operation Ice VendingDispense Area Sanitation To Sanitize Cleaning and SanitizingScotsman Ice Machine Cleaner contains acids Check and tighten all bolts and screws Moving Parts Hazard Maintenance and CleaningSymptom Possible Cause Probable Correction Service DiagnosisMDT5N25 & MDT5N40 Power Service Diagnosis Circuit BoardOff Timer Bin EmptyBIN Controls Ice Level Sensors Removal and ReplacementTo Remove the Breaker Bearing Assembly Removal and Replacement Bearing And BreakerTo Remove the Auger To Replace the Water Seal Removal and Replacement Water SealTo Remove the Water Seal To Reassemble the Evaporator and Auger For Access to the Evaporator to Gearmotor boltsTo Replace the Evaporator To Inspect the gearmotor To Remove and Repair the Gearmotor AssemblyElectrical Shock Hazard Do not USE Mineral OIL in this Refrigeration System Refrigeration Service R-404A HP62Only a HFC type dryer should be used Refrigeration ServiceGeneral Information Printed Circuit Board Handling Precautions Circuit Board ServiceLiquid Charging Instructions for R-404A

MDT5N40, MDT5N25 specifications

The Scotsman Ice MDT5N25 and MDT5N40 models are part of a sophisticated line of ice machines designed for commercial use. These models stand out for their efficiency, reliability, and advanced technology, making them ideal for restaurants, bars, and other food service establishments that require a constant supply of ice.

One of the main features of the Scotsman MDT5N25 and MDT5N40 models is their ability to produce high volumes of ice quickly while maintaining energy efficiency. These machines are designed to provide a steady supply of ice, ensuring that businesses can meet the demands of their customers without interruption. The MDT5N25 can produce approximately 260 pounds of ice per day, while the MDT5N40 takes it a step further by producing around 450 pounds daily. These capacities make both models suitable for various applications, from small cafes to larger dining venues.

Both models are equipped with Scotsman’s proprietary EcoX technology, which enhances energy efficiency and reduces water consumption. This technology employs advanced engineering designs that minimize waste and optimize production cycles. This focus on sustainability not only helps reduce operational costs but also appeals to environmentally conscious businesses.

The MDT5N25 and MDT5N40 also feature a self-cleaning mechanism that simplifies maintenance and ensures consistent ice quality. The automatic cleaning cycle helps prevent limescale and bacteria buildup, providing peace of mind for operators who prioritize hygiene and food safety.

In terms of design, both models boast a compact footprint, making them suitable for establishments with limited space. They come with a built-in storage bin that efficiently holds large quantities of ice, streamlining operations and making it easy for staff to access ice when needed. The sleek stainless steel finish of the machines not only enhances their durability but also ensures they can blend seamlessly into any commercial kitchen environment.

The user-friendly control panel on both the MDT5N25 and MDT5N40 allows for easy adjustments and monitoring of the machine’s performance. Operators can easily keep track of production levels and patterns, ensuring they can manage their ice supply effectively.

In conclusion, the Scotsman Ice MDT5N25 and MDT5N40 models represent a robust solution for commercial ice production, combining efficiency, advanced technology, and ease of use. With their impressive output capacities, energy-efficient designs, self-cleaning features, and durable construction, these machines are perfect for businesses that rely on consistent ice production to meet their needs.