| Rear Support Continued... |
|
|
| nuts (may not be supplied), fabricate | Sound Framing Members |
|
Tools Needed: |
|
| |
rear support for horizontal tracks. Attach |
|
| |
|
|
| |
| horizontal tracks to the rear supports with |
|
|
|
|
| |
| (may not be supplied). Horizontal tracks |
|
|
| must be level and parallel with door. |
| 30” ANGLE - BOLTED |
| NOTE: If rear supports are to be installed | 12” ANGLE | USING (2) 5/16” X |
| over drywall, use 5/16” x 2” hex head lag |
| HEX HEAD LAG SCREWS |
| screws. |
| TO CEILING MEMBER AND |
| NOTE: If an idrive® opener will be |
| PARALLEL TO DOOR |
| installed, position horizontal tracks one |
|
|
| hole above level when securing it to rear |
| BOLT MUST EXTEND INTO |
| supports. | HORIZONTAL TRACK | |
| Adjust weather seal (if necessary). |
| THE TRACK TO SERVE AS |
| Permanently attach the weather seal to |
| A ROLLER STOP |
| both door jambs and header. (Temporarily |
|
|
| attached in PREPARING THE OPENING on | Sound Framing Members |
|
| page 10.) Avoid pushing weather seal too |
| |
| tightly against face of door. |
|
|
| Now, lift door and check it’s balance. |
|
|
| WARNING |
|
|
| Prior to winding or making adjustments |
| 30” ANGLE - BOLTED |
| to the springs, ensure you’re winding | 12” ANGLE | USING (2) 5/16” X |
| in the proper direction as stated in the | HEX HEAD LAG SCREWS | |
|
| ||
| Installation Instructions. Otherwise |
| TO CEILING MEMBER |
| the spring fittings may release from |
| AND PARALLEL TO DOOR |
| spring if not wound in the proper |
|
|
| direction and could result in severe or | HORIZONTAL TRACK |
|
| fatal injury. | BOLT MUST EXTEND INTO | |
| Adjust, if door lifts by itself (hard to pull |
| THE TRACK TO SERVE AS |
| down) or if door is difficult to lift (easy to |
| A ROLLER STOP |
| pull down). Anytime spring adjustments | PERFORATED ANGLE |
|
| are made you must loosen the lock nuts |
| |
|
|
| |
| and retighten both lock nuts afterwards. |
|
|
| To adjust spring(s), only add or remove |
|
|
| 1/4 turn on the counter at a time. Adjust |
| weather |
| both sides equally. |
| |
| IMPORTANT: Do not add or remove |
| seal |
|
|
| |
| more than 1 spring turn from |
|
|
| specified amount. If the door still |
|
|
| does not operate easily, lower |
| jamb |
| the door into the closed position, |
| |
| UNWIND SPRING(S) TO ZERO, and | (3) 5/16” |
|
| recheck the following items: |
| |
| 1.) Check the door for level. | BOLTS & NUTS | permanently attached |
| 2.) Check the TorqueMaster® spring tube | weather seal or door stop | |
| and flagangles for level and plumb. |
|
|
| 3.) Check the distance between the |
|
|
| flagangles - must be door width |
|
|
| plus |
|
|
| 4.) Check the counterbalance cables |
|
|
| for equal tension - adjust if |
|
|
| necessary. |
|
|
| 5.) Rewind the spring(s). |
|
|
| 6.) Make sure door isn’t rubbing on |
|
|
| jambs. |
|
|
| NOTE: As a safety feature, the right hand end |
|
|
| bracket cannot be disassembled for service |
|
|
| until the spring is completely unwound and the |
|
|
| counter cover reads zero. |
|
|
| After door installation is completed, refer to the |
|
|
idrive® owner’s manual.
31
INSTALLATION
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at