15 | Attaching Adjustable Flagangle | flagangle | 1/4” - 20 X 9/16” |
|
large head |
| |||
|
| |||
to Horizontal Track |
| ribbed track |
| |
NOTE: If quick install flagangles were |
| bolts |
| |
Tools Needed: |
|
|
| |
installed in Step 14, skip this step and |
|
|
| |
|
|
|
| |
7/16” Socket | continue with Step 16. If not, complete this |
|
|
|
step. |
|
|
| |
|
|
|
| |
9/16” Socket | To install horizontal track, place the curved |
|
|
|
Ratchet Wrench | end over the top roller. Align the bottom of |
|
|
|
the horizontal track with the vertical track. |
|
|
| |
9/16” Wrench | Hand tighten the horizontal track to the |
|
|
|
flagangle with (2) 1/4” - 20 x 9/16” large |
|
|
| |
Level | head ribbed track bolts (or stud plate if |
|
|
|
included) and (2) |
|
|
| |
Screwdriver | hex nuts |
|
| |
WARNING |
|
| ||
Flat Tip |
|
|
| |
| DO NOT RAISE DOOR UNTIL HORIZONTAL |
| stud plate |
|
|
|
|
| |
| TRACKS ARE SECURED AT REAR, AS |
|
|
|
| OUTLINED IN STEP 34, OR DOOR COULD | 3/8” - 16 X 3/4” |
|
|
| FALL FROM OVERHEAD POSITION CAUSING | 3/8” - 16 Hex nut |
| |
| TRUSS HEAD BOLT |
| ||
| SEVERE OR FATAL INJURY. |
| ||
|
|
|
| |
| Level the horizontal track assembly and |
|
|
|
| bolt the horizontal angle to the slot in the |
|
|
|
| flagangle using (1) 3/8” - 16 x 3/4” truss |
| horizontal ANGLE | INSTALLATION |
| could cause permanent damage to |
| ||
| head bolt and (1) 3/8” - 16 hex nut. Repeat |
|
|
|
| for other side. Remove the nail that was |
|
|
|
| temporarily holding the top section in |
|
|
|
| place, installed in Step 13. |
|
|
|
| IMPORTANT: Failure to remove nail |
|
|
|
| before attempting to raise door |
|
|
|
| top section. |
|
|
|
| NOTE: If an idrive® opener will be installed, |
|
|
|
| position horizontal tracks slightly above |
| HORIZONTAL TRACK |
|
16 | level. |
|
| |
Adjusting Top Brackets |
| HORIZONTAL |
| |
|
|
| ||
|
| track |
| |
Tools Needed: |
| top |
|
|
With horizontal tracks installed, you can | section |
|
| |
|
|
|
| |
7/16” Wrench | now adjust the top brackets. |
|
|
|
|
|
|
| |
| Vertically align the top section of the |
|
|
|
| door with the lower sections. Once |
|
|
|
| aligned, position the top bracket slide, |
|
|
|
| out against the horizontal track. |
|
|
|
|
| top |
|
|
| Maintaining the slide’s position, tighten | SECTION |
|
|
| the (2) 1/4” - 20 flange hex nuts to | Correct |
|
|
| secure the top roller slide to the top |
|
|
|
| bracket base. |
| TOP |
|
|
|
|
| |
|
|
| BRACKET |
|
|
| top | SLIDE |
|
|
|
|
| |
|
| section |
|
|
|
| (2) 1/4” - 20 |
|
|
|
| FLANGE HEX |
|
|
|
| NUTS |
|
|
|
| inCorrect |
|
|
|
|
| 19 |
|
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at
