Wayne-Dalton 9600 installation instructions Trolley Installation for, Standard Lift

❉	Trolley Installation for	Determine the Wayne-Dalton			Level
	Standard Lift	track radius being used:				HIGH ARC
Measure the curved ends of the horizontal track to determine		Horizontal
		track
if you have a 12” or 15” radius horizontal track, as shown
in FIG. 2.1. Determine center line of door. Mark vertical line			12” or 15”			TOP
at this point, on the header wall. Raise the door slightly until
						SECTION
the top section reaches the highest point of travel (high arc).
Using a level, mark this high arc point of travel on the header						FIG. 2.2
wall, intersecting the vertical center line, as shown in FIG.		FIG. 2.1
2.2 through 2.3. Hold the wall bracket’s bottom edge to the
appropriate 1/2” - 1” (room permitting) above of the high		Typical 1/2” - 1” above high arc
arc line and centered on the vertical line, as shown in FIG.		HIGH ARC	Torquemaster®
2.3. Spot the wall brackets mounting holes on the header			Counterbalance
		line
wall and then refer to your garage door operator manual for						Straight
pre-drilling and securing the wall bracket to header. Using the						arm
operator hook-up charts, refer to referenced illustrations
in FIG. 2.4 through FIG. 2.5 for correct arm hook-up from					Curved
trolley to operator bracket.			Vertical		arm	Cut Straight
		From	center line			arm to
NOTE: Refer to your operator manual for specific details on		step 12	Header			accomplish
how to assembly the curved and straight arm, as shown in						trolley
						setting
FIG. 2.4 through FIG. 2.5.
NOTE: Depending on your setup, you may or may not have to		FIG. 2.3
					Locking
cut straight arm to accomplish trolley settings, as shown in
					hex nut
FIG. 2.4 through FIG. 2.5.
		CURVED				Operator
Attach door arm to trolley and align the appropriate door arm		Straight	arm			Bracket
hole with the hole in the door operator bracket. Insert (1) hex
		arm				Hex bolt
head bolt through hole of operator bracket and door arm.
Install (1) Locking hex nut and just tighten until snug.			Cut Straight
WARNING			arm to
			accomplish	Straight arm
			trolley
Failure to use locking nut can result in arm re-			setting	shown		FIG. 2.6
leasing and possible resulting in property damage		FIG. 2.5
and/or personal injury.
Quantum and classic Operators require:		Operator hook-up chart Standard lift For 12” radius
		Operator models	Type of arm Being used		Ref. Illustrations above
(1) 3/8” - 16 x 1” hex bolt and (1) 3/8” - 16 locking hex nut,
		Quantum/classic	Curved / Straight			Fig. 2.5
as shown in FIG. 2.6.
		Linear	Straight / Curved			Fig. 2.4
Linear, Liftmaster (Sears), Genie Operators		Liftmaster	Curved / Straight			Fig. 2.5
require:		(sears)
(1) 5/16” - 18 x 1” hex bolt and (1) 5/16” - 18 locking hex		Genie	Curved / Straight			Fig. 2.5
nut, as shown in FIG. 2.6.
		Operator hook-up chart Standard lift For 15” radius
		Operator models	Type of arm Being used		Ref. Illustrations above
		Quantum/classic	Curved / Straight			Fig. 2.5
		Linear	Straight / Curved			Fig. 2.4
		Liftmaster	Curved / Straight			Fig. 2.5
		(sears)
		Genie	Curved / Straight			Fig. 2.5

34

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com