Scotsman Ice Complete Manual for Repairing Your Scotsman MDT5N25A Ice Maker Gearmotor

Page 29
GEARCASE
COVER

MDT5N25 & MDT5N40

TO REMOVE AND REPAIR THE GEARMOTOR ASSEMBLY

(Assuming that the procedures through removal of the water seal have been performed.)

Electrical Shock

Hazard.

Disconnect electrical power to the icemaker - dispenser before beginning.

1.Remove the electrical wires from the gear drive motor.

2.Unscrew the 4 cap screws holding the gearmotor to the gearmotor plate.

3.Remove the gearmotor from the icemaker.

To Inspect the gearmotor.

onto the lower case, cover will have to be moved closer to the second gear after the output gear has cleared the second gear top bearing.

E)After the case is together, and the locating pins are secure in both ends, replace all cap screws.

4.Bench test the gearmotor, check for oil leaks, noise, and amp draw.

A)Remove the cap screws holding the gearmotor case halves together and pry the two cases apart.

B)To lift off the cover, lift up until you can feel internal contact, then pull the cover towards the output gear end, and then

lift the cover (with drive motor attached) up and away from the gear motor case.

Note: The case cover output gear, bearings, and shaft are one pressed together assembly. Replace as a unit.

C)Inspect the oil, gears, and bearings. If the oil level and condition is acceptable,

quickly check the gears and bearings. They are likely to be fine if the oil is.

If there is evidence of water in the oil (rusty bearings and gears; the oil having a creamy white appearance; oil level too high) carefully inspect the bearings and gears. If in doubt about the condition of a part, replace it. The oil quantity is 16 fluid ounces, do not overfill.

Note: The gears and bearings are available only as pressed together sets.

D) After replacing parts as required, (if any) reassemble the gearcase. The two smaller gears and the oil should be in the lower case, the output gear will be with the cover. As you lower the cover

May 2001

Page 29

ROTOR

BEARING

FIRST GEAR &

BEARINGS

GASKET

Image 29
Contents Introduction Table of ContentsMDT5N25 & MDT5N40 Installation Limitations Service Limitations For the Installer Environmental LimitationsMinimum Maximum Water LimitationsMachine Stand Installation For the InstallerCounter Top or Machine Stand Installation Unpack and install the ice and water spoutsFor the Installer Wall Mount Kit Conform to ALL Applicable Codes For the PlumberFor the Electrician For the Installer Final Check List Start Up Initial Start UPPre Start Inspection Component Description ICE Sweep Bearing Breaker Motor Evaporator Auger Water Seal Component Description Control Box On/Off Switch ManualCircuit Board Potential RelayElectrical Sequence Splash panel cleaningStart up consists Shut Down consistsOperation Water Operation Refrigeration Refrigeration SchematicContainer Operation Ice VendingDispense Area Sanitation To Sanitize Cleaning and SanitizingScotsman Ice Machine Cleaner contains acids Check and tighten all bolts and screws Moving Parts Hazard Maintenance and CleaningSymptom Possible Cause Probable Correction Service DiagnosisMDT5N25 & MDT5N40 Power Service Diagnosis Circuit BoardOff Timer Bin EmptyBIN Controls Ice Level Sensors Removal and ReplacementTo Remove the Breaker Bearing Assembly Removal and Replacement Bearing And BreakerTo Remove the Auger To Replace the Water Seal Removal and Replacement Water SealTo Remove the Water Seal To Reassemble the Evaporator and Auger For Access to the Evaporator to Gearmotor boltsTo Replace the Evaporator To Inspect the gearmotor To Remove and Repair the Gearmotor AssemblyElectrical Shock Hazard Do not USE Mineral OIL in this Refrigeration System Refrigeration Service R-404A HP62Only a HFC type dryer should be used Refrigeration ServiceGeneral Information Printed Circuit Board Handling Precautions Circuit Board ServiceLiquid Charging Instructions for R-404A

MDT5N40, MDT5N25 specifications

The Scotsman Ice MDT5N25 and MDT5N40 models are part of a sophisticated line of ice machines designed for commercial use. These models stand out for their efficiency, reliability, and advanced technology, making them ideal for restaurants, bars, and other food service establishments that require a constant supply of ice.

One of the main features of the Scotsman MDT5N25 and MDT5N40 models is their ability to produce high volumes of ice quickly while maintaining energy efficiency. These machines are designed to provide a steady supply of ice, ensuring that businesses can meet the demands of their customers without interruption. The MDT5N25 can produce approximately 260 pounds of ice per day, while the MDT5N40 takes it a step further by producing around 450 pounds daily. These capacities make both models suitable for various applications, from small cafes to larger dining venues.

Both models are equipped with Scotsman’s proprietary EcoX technology, which enhances energy efficiency and reduces water consumption. This technology employs advanced engineering designs that minimize waste and optimize production cycles. This focus on sustainability not only helps reduce operational costs but also appeals to environmentally conscious businesses.

The MDT5N25 and MDT5N40 also feature a self-cleaning mechanism that simplifies maintenance and ensures consistent ice quality. The automatic cleaning cycle helps prevent limescale and bacteria buildup, providing peace of mind for operators who prioritize hygiene and food safety.

In terms of design, both models boast a compact footprint, making them suitable for establishments with limited space. They come with a built-in storage bin that efficiently holds large quantities of ice, streamlining operations and making it easy for staff to access ice when needed. The sleek stainless steel finish of the machines not only enhances their durability but also ensures they can blend seamlessly into any commercial kitchen environment.

The user-friendly control panel on both the MDT5N25 and MDT5N40 allows for easy adjustments and monitoring of the machine’s performance. Operators can easily keep track of production levels and patterns, ensuring they can manage their ice supply effectively.

In conclusion, the Scotsman Ice MDT5N25 and MDT5N40 models represent a robust solution for commercial ice production, combining efficiency, advanced technology, and ease of use. With their impressive output capacities, energy-efficient designs, self-cleaning features, and durable construction, these machines are perfect for businesses that rely on consistent ice production to meet their needs.