GE 164D2966P126 warranty Broiling, CLEAR/OFF pad. Serve the food, Immediately, and leave the pan

Page 27

BROILING

.—

—

ur double oven has controls for the upper oven and the lower oven. Be sure to set the correct control. Pads on the left side of the panel are for the upper oven. Pads on the right side of the panel are for the lower oven. The TIMER ON/OFF, COOK TIME, STOP TIME, INCREASE and DECREASE pads can be used for either oven.

“—

Broiling is cooking food by intense radiant heat from the upper broil element in the oven. You can broil in the upper or the lower oven. Most fish and tender cuts of meat can be broiled. Follow these directions to keep spattering and smoking to a minimum.

Turn the food using tongs only once during broiling. Time the foods for the first side according to the Broiling Guide.

Turn the food. then use the times given for the second side as a guide to prefemed doneness.

1.If the meat has fat or gristle around the edge, cut vertical slashes throu&h both about 2 inches apart. If desired, the fat may be trimmed, leaving: a layer about 1/8 inch thick.

2.Place the meat on the broiler grid in the broiler pan Always use the grid so the fat drips into the broiler pan; otherwise the juices may become hot enough to catch on fire.

3.Position a flat shelf on the recommended shelf position as suggested in the Broiling Guide. Most broiling is done on C position, but if your oven is connected to 208 volts, you may wish to use a higher position.

Leave door open to the broil stop position. The door stays open by itself, yet the proper temperature is maintained in the ., ten.

5.Press the BROIL pad. Preheating the

JHI = Q elements is not necessary. (See the

B;o& Comments column in the Broiling

A- Guide.)

6. Press the INCREASE pad for HI Broil or press the DECREASE pad for LO Broil.

@

 

(a To change from HI Broil to LO Broil,

 

press the DECREASE pad once.

9

 

v

 

 

7. When broiling is finished press the

CLEAR

CLEAR/OFF pad. Serve the food

immediately, and leave the pan

OFF

outside the oven to cool during the

0 meal for easiest cleaning.

NOTE: A fan may automatically turn on and off to cool internal parts. This is normal and the fan may continue to run even after the oven is turned off.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Useand Care Guide Help US Help YOU If YOU Need ServiceEnforcement Act requires the Governor Mportant Safety InstructionsOven Mportant Safety ~STRUCTIONSSelf-Cleaning Oven Save These InstructionsProbe Features of Your OvensExplained Bake ElementQQ9 Features of Your Oven ControlPower Outage To Set the TimerTo Reset the Timer To Cancel the TimerChild Lockout Feature Display MessagesIncrease and Decrease Pad Speed Using Your Oven Re Using Your OvenOven Shelves Offset Shelf Shelf PositionsOven Lights Convection Cooking IVhen should you use Convection Bake or Convection Roast?Cookware for Convection Cooking Clear Convection BA~NGAdapting Recipes For Convection Baking Multi-Shelf BakingTo start.To set the clock, first press Timed Convection BA~NGTo Convection Time Bake Day is displayed. Press the Clock padQuick Reminder How to Set Delay Start and Automatic Stop Convection BakeFi...- --.-~y’ Roast ROASI’INJ~50 Pot Roast 2~ t 3 lbs, Chuck, Rump Convection Roasting GU~ERegular Baking MediumBaking Pans Pan PlacementWgular Baking PreheatingCakes Ing GuidesCookies PiesHow to Time Bake How to Set Immediate Start and Automatic StopRegular T~ED BA~NG Clear OFF Low to Set Delay Start and Automatic StopOven as yOLI would norrnay Adjust the Oven ThewostatPress he CLEAR/OFF pad to go back To the time of day display. Use yOLuTo change the oven temperature during ~GULAR RoastingUse of Aluminum Foil Casseroles or Fish Correct Placement of the Temperature ProbeRegular Roasting with the Probe Ham or LambProbe Page Immediately, and leave the pan Meal for easiest cleaningBroiling CLEAR/OFF pad. Serve the foodShould I salt the meat before broiling? Questions and AnswersSteaks less than 1 inch thick cook Broiling GU~EOven door should be open to the broil Lb. about Arran&e in single layer~~lke sLIre the o\’en light bulb cover is in pl~~ce Before a Clean CycleOr oven cleaners ~’iarl spaters or soi 1 on the oven front frameStop OW to Set Oven for CleaningTo Stop a Clean Cycle CleanHow to Set Delay Start of Cleaning After Self-Cleaning~uestions and Answers Oven Shelves and Convection Roasting Rack Broiler Pan and GridInside of the door ~ift-Off Oven DoorOven door is Removable, but it is To remove the doorTo remove Oven Light ReplacementProbe Oven Heating ElementsMetal Parts QUESTIONS? USE this Problem SolverDontrol Panel Glass WindowGE Answer Center@ Consumer information service We’ll Be There Warranty

164D2966P126 specifications

The GE 164D2966P126 is a critical component in the realm of industrial and aerospace applications, offered by General Electric. This part exemplifies advanced engineering designed to fulfill high-performance requirements in demanding environments. Its reliability and efficiency make it suitable for a variety of uses, with a particular focus on power generation and distribution systems.

One of the main features of the GE 164D2966P126 is its robust construction. Built to withstand extreme operating conditions, this part demonstrates exceptional durability in the face of thermal fluctuations, pressure variations, and mechanical stresses. This resilience is essential for components utilized in the aerospace industry, where failure is not an option.

The technology integrated into the GE 164D2966P126 is another standout characteristic. With advancements in materials science, the component is manufactured using lightweight yet strong materials that contribute to overall efficiency. This approach minimizes weight without compromising structural integrity, which is crucial in aviation applications where every ounce matters.

Additionally, the GE 164D2966P126 employs cutting-edge manufacturing techniques that ensure precision and quality. The use of CNC machining and additive manufacturing processes enhances the component's design flexibility while maintaining tight tolerances. This precision is vital for parts that must fit seamlessly within complex systems.

The electrical characteristics of the GE 164D2966P126 are optimized to handle varying loads, making it an indispensable part of electrical control and distribution systems. Its ability to maintain performance under fluctuating conditions aligns well with modern energy management strategies, promoting efficiency and sustainability.

Moreover, the GE 164D2966P126 is characterized by its ease of integration into existing systems. It is designed to work with other components seamlessly, reducing installation time and costs. This compatibility is essential for industries that require rapid upgrades and scalability.

In conclusion, the GE 164D2966P126 represents a pinnacle of engineering innovation, embodying durability, efficiency, and advanced technology. Its robust features and exceptional characteristics make it ideal for applications in power generation and aerospace, ensuring that it meets the high standards expected in these critical sectors. With General Electric's commitment to excellence, the 164D2966P126 continues to support industries that depend on reliable performance and cutting-edge technology.
Top Page Image Contents