GE 206C1559P195 Insert drain hose and Power CORD, if USED, through cabinet

Page 9
Side-
Mounting Brackets

Dishwasher Installation

Note: The drain hose supplied with the dishwasher is approximately 78" long. If a longer hose is needed, a 10-foot-long hose may be purchased from an authorized GE appliance dealer. The 10-foot-long hose is part number GPF10S.

 

Strain

 

Relief

Figure L

Drain Hose

Hose Stop

Do not use

 

this port if

 

present

Hose Clamp

STEP 9: insert drain hose AND POWER CORD, IF USED, through cabinet

•Upright the dishwasher and position it in front of the cabinet opening.

•Insert the drain hose into the hole previously drilled in the cabinet wall.

•If a power cord is used, guide the end of the cord through a separate hole cut for the power cord.

The power cord should be routed directly to the rear of the junction box, avoiding contact with the door spring and other dishwasher components.

Drain

Power

Water

Figure O

Drain Hose Collection Chamber

Figure M

Drain Port

 

Tip: Avoid unnecessary service charges for drain issues.

Make sure the drain hose connection is leak-free and the hose is routed through the strain relief so it will not kink when the dishwasher is installed into the cabinet.

STEP 8: POSITION WATER LINE AND POWER SUPPLY

•Position the water supply line and house wiring on the floor of the opening to avoid interference with the base of the dishwasher and components under the dishwasher.

Tip: Avoid unnecessary service charges for no fill, drain or noise concerns.

Position utility lines so they do not interfere with anything under or behind the dishwasher.

STEP 10: inSTALL OPTIONAL GPF65 SIDE MOUNT BRACKETS

Skip this step if the underside of countertop is wood or woodlike material.

•Purchase and install the GPF65 side-mount bracket kit if the underside of counter is granite or a similar material that will not accept wood screws. The GPF65 kit is available from authorized GE appliance dealers.

•Refer to Figure P and follow the instructions

included in the kit.

 

Tub Frame

 

 

 

Water

Power

 

Bracket

 

Line

Supply

 

 

 

Attachment

 

 

 

 

 

 

Optional

 

Screws

 

Figure N

Side-Mount

Figure P

(2 Each

 

Bracket Kit

Side)

 

 

9

 

 

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Read Carefully Keep These Instructions Read these instructions completely and carefullyImportant Observe all governing codes and ordinances For New Installations Parts Supplied in Installation PackageMaterials YOU will Need Tools YOU will NeedPrepare Dishwasher Enclosure Installation Preparation EnclosureInstallation Preparation Drain Important WhenPrepare Drain Plumbing Prepare Electrical Wiring Installation Preparation Electrical SupplyCabinet Preparation and Wire Routing Electrical RequirementsPrepare Hot Water Supply Installation Preparation Hot Water SupplyHot Water Line Water Line ConnectionRemove Access Panel Toekick Dishwasher InstallationPreparation Check Door BalanceInstall 90 Elbow Install Power CordInstall drain hose to dishwasher drain port Skip this step if drain hose has been preinstalledTip Avoid unnecessary service charges for drain issues Insert drain hose and Power CORD, if USED, through cabinetTip Avoid unnecessary service charges for panel damage Position and level dishwasherSlide Dishwasher Into Cabinet Connect water supply Tip Avoid unnecessary service charges for noise or leaksFigure W Connect Drain LineInstall junction box cover Connect Power SupplyPretest checklist If junction box cover is already installed, skip to StepCycles Dishwasher wet test checklistLiterature Replace access panel and toekickReturn to in these instructions to complete the conversion AppendixImportant Observez tous les codes et ordonnances en vigueur Veuillez Lire Attentivement ET Conserver CES DirectivesPièces Fournies Pour UNE Nouvelle InstallationMatériel Nécessaire Outils NécessairesPréparation DE Louverture Dans LES Armoires Préparation pour linstallation Ouverture dans les armoiresPréparation DE LA Plomberie Pour LA Vidange Préparation pour l’installation VidangePréparation DU Câblage Électrique Préparation pour l’installation Alimentation électriquePréparation DE L’ALIMENTATION EN EAU Chaude Préparation pour l’installation Alimentation en eau chaudeConduite d’eau chaude Raccordement de la conduite d’eau chaudeÉtape 1 Préparation Installation du lave-vaisselleÉtape 3 Enlèvement DE LA Base DE Bois La base de boisQue les fils ne sont pas coincés sous le couvercle Étape 5 Installation DU Cordon ’ALIMENTATIONDu boyau de 3 mètres de long est le GPF10S Remarque Le boyau de vidange fourni avecFigure R Étape 12 Mise DE Niveau DU LAVE- VaisselleFerruleBague Étape 14 Raccordement DE L’ALIMENTATION EN EAUFigure W Étape 15 Raccordement DU Boyau DE VidangeHexagonale n 10 de l’ensemble de vis mis de côté ’étape Assurez-vous que le tableau de commandeLa source Ouvrez la porte du lave-vaisselle et enlevez toutRétablissez l’alimentation électrique ou DE L’EAUVerrouillez la porte du lave-vaisselle La touche Start Mise en marcheÉtape 21 Documentation Deux types de vis sont utilisés. Les vis n 8-32En place le panneau d’accès et le panneau inférieur Annexe Enlevez et jetez le cordon d’alimentationReportez-vous à la Figure CC

206C1559P195 specifications

The GE 206C1559P195 is a component that belongs to General Electric's suite of high-performance aircraft engine components. Specifically, this part is integral to the Geared Turbofan (GTF) engine technology that GE has pioneered, aiming at increasing fuel efficiency while reducing noise and emissions.

One of the standout features of the GE 206C1559P195 is its advanced aerodynamic design, which plays a crucial role in optimizing the engine's performance. The component helps improve air flow, thereby enhancing thrust and operational efficiency. By utilizing sophisticated Computational Fluid Dynamics (CFD) simulations in its design process, GE has ensured that the part meets the rigorous demands of modern aviation.

The GE 206C1559P195 also incorporates cutting-edge materials technology. Constructed with lightweight yet robust materials, the part significantly contributes to the overall weight reduction of the engine, which is vital for maximizing fuel efficiency. The use of composite materials and advanced alloys ensures that the component can withstand extreme temperatures and pressures associated with high-performance engine operation.

Another characteristic that sets the GE 206C1559P195 apart is its reliability and durability. GE's stringent manufacturing processes and quality control protocols ensure that each component is built to last, reducing maintenance frequency and enhancing operational reliability. The part is designed to have a long service life, making it a cost-effective choice in the long run for airlines and operators.

In terms of technological innovation, the GE 206C1559P195 features integrated sensors that provide real-time data on engine performance. This capability allows for better monitoring and predictive maintenance, thereby increasing safety and reducing unscheduled downtimes.

Furthermore, the integration of digital twin technology enables operators to simulate different operational scenarios, improving decision-making and optimizing maintenance schedules. This technological edge places the GE 206C1559P195 at the forefront of aircraft engine component innovations, aligning with the industry's shift toward sustainability and efficiency.

In summary, the GE 206C1559P195 is a remarkable component that embodies GE's commitment to advance aviation technology, emphasizing performance, durability, and environmental awareness. Its design and technological features reflect the ongoing evolution in the aerospace industry, making it a key asset for modern aircraft engines.
Top Page Image Contents