GE 206C1559P195 Dishwasher Installation, Preparation, Check Door Balance, Remove Wood Base

Page 7
Figure I

Dishwasher Installation

CAUTION

Do not remove the wood base until you are ready to install the dishwasher. The dishwasher will tip over when the door is opened if the base is removed.

PRECAUCIÓN

No retire la base de madera hasta que esté listo para instalar la lavadora de platos. Cuando la puerta se abra, la lavadora de platos se inclinará si la base se retira.

STEP 1: PREPARATION

Locate the items in the installation package and set them aside for use in the listed steps.

•Screw kit – Steps 5 or 16 and 13

•Junction box cover – Steps 5 or 16

•Drain hose and drain hose clamp – Step 7

•Owners’ Manual – Steps 18 and 21

•Product Samples and/or coupons – Step 21

•Conversion leads (Factory-equipped power cord models only) – Appendix

STEP 2: CHECK DOOR BALANCE

•With the dishwasher on the wood base, check the door balance by opening and closing the door.

•The door is properly balanced if it gently drops from a 1/2 open position and does not rise from the full open position.

•If necessary, increase or decrease tension as shown. Latch the door and adjust springs to correct balance.

Link fully seated in hinge arm

Insert Hook Through

Hole from Inside of Frame

Figure G

Tip: Avoid service calls for door balance problems. Make sure the spring end is fully engaged in a frame hole and the spring link is fully seated in the hinge arm.

STEP 3: REMOVE WOOD BASE

IMPORTANT – Do not kick off wood base!

Damage will occur.

•Move the dishwasher close to the installation location and lay it on its back.

•Remove the four leveling

legs from the underside of the wood base

with a 15/16" socket wrench.

• Remove and discard wood base.

Figure H

•Screw leveling legs back into the dishwasher frame, approximately 3/4" from the frame, as shown.

STEP 4: REMOVE ACCESS PANEL

AND TOEKICK

The top mounting holes in the access panel are slotted.

•Remove the lower two 10-16 x 3/8" sheet metal screws. Do not remove the two top 8-32 x 1/4" machine thread screws.

•Slide the access panel to the left as far as it will go.

•Gently pull the access panel forward to remove

it from the top screws.

Set access panel, toekick and screws aside for use in Step 20.

Tip: Prevent

tub damage. Remove only the 3/8" sheet metal screws in this step.

This will help prevent a mix- up with the 1/4" machine thread screws in Step 20.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Read these instructions completely and carefully Read Carefully Keep These InstructionsImportant Observe all governing codes and ordinances Tools YOU will Need Parts Supplied in Installation PackageFor New Installations Materials YOU will NeedPrepare Dishwasher Enclosure Installation Preparation EnclosureImportant When Installation Preparation DrainPrepare Drain Plumbing Electrical Requirements Installation Preparation Electrical SupplyPrepare Electrical Wiring Cabinet Preparation and Wire RoutingWater Line Connection Installation Preparation Hot Water SupplyPrepare Hot Water Supply Hot Water LineCheck Door Balance Dishwasher InstallationRemove Access Panel Toekick PreparationSkip this step if drain hose has been preinstalled Install Power CordInstall 90 Elbow Install drain hose to dishwasher drain portTip Avoid unnecessary service charges for drain issues Insert drain hose and Power CORD, if USED, through cabinetPosition and level dishwasher Tip Avoid unnecessary service charges for panel damageSlide Dishwasher Into Cabinet Connect water supply Tip Avoid unnecessary service charges for noise or leaksFigure W Connect Drain LineIf junction box cover is already installed, skip to Step Connect Power SupplyInstall junction box cover Pretest checklistCycles Dishwasher wet test checklistLiterature Replace access panel and toekickReturn to in these instructions to complete the conversion AppendixImportant Observez tous les codes et ordonnances en vigueur Veuillez Lire Attentivement ET Conserver CES DirectivesOutils Nécessaires Pour UNE Nouvelle InstallationPièces Fournies Matériel NécessairePréparation DE Louverture Dans LES Armoires Préparation pour linstallation Ouverture dans les armoiresPréparation DE LA Plomberie Pour LA Vidange Préparation pour l’installation VidangePréparation DU Câblage Électrique Préparation pour l’installation Alimentation électriqueRaccordement de la conduite d’eau chaude Préparation pour l’installation Alimentation en eau chaudePréparation DE L’ALIMENTATION EN EAU Chaude Conduite d’eau chaudeLa base de bois Installation du lave-vaisselleÉtape 1 Préparation Étape 3 Enlèvement DE LA Base DE BoisQue les fils ne sont pas coincés sous le couvercle Étape 5 Installation DU Cordon ’ALIMENTATIONDu boyau de 3 mètres de long est le GPF10S Remarque Le boyau de vidange fourni avecFigure R Étape 12 Mise DE Niveau DU LAVE- VaisselleFerruleBague Étape 14 Raccordement DE L’ALIMENTATION EN EAUFigure W Étape 15 Raccordement DU Boyau DE VidangeOuvrez la porte du lave-vaisselle et enlevez tout Assurez-vous que le tableau de commandeHexagonale n 10 de l’ensemble de vis mis de côté ’étape La sourceLa touche Start Mise en marche DE L’EAURétablissez l’alimentation électrique ou Verrouillez la porte du lave-vaisselleDeux types de vis sont utilisés. Les vis n 8-32 Étape 21 DocumentationEn place le panneau d’accès et le panneau inférieur Enlevez et jetez le cordon d’alimentation AnnexeReportez-vous à la Figure CC

206C1559P195 specifications

The GE 206C1559P195 is a component that belongs to General Electric's suite of high-performance aircraft engine components. Specifically, this part is integral to the Geared Turbofan (GTF) engine technology that GE has pioneered, aiming at increasing fuel efficiency while reducing noise and emissions.

One of the standout features of the GE 206C1559P195 is its advanced aerodynamic design, which plays a crucial role in optimizing the engine's performance. The component helps improve air flow, thereby enhancing thrust and operational efficiency. By utilizing sophisticated Computational Fluid Dynamics (CFD) simulations in its design process, GE has ensured that the part meets the rigorous demands of modern aviation.

The GE 206C1559P195 also incorporates cutting-edge materials technology. Constructed with lightweight yet robust materials, the part significantly contributes to the overall weight reduction of the engine, which is vital for maximizing fuel efficiency. The use of composite materials and advanced alloys ensures that the component can withstand extreme temperatures and pressures associated with high-performance engine operation.

Another characteristic that sets the GE 206C1559P195 apart is its reliability and durability. GE's stringent manufacturing processes and quality control protocols ensure that each component is built to last, reducing maintenance frequency and enhancing operational reliability. The part is designed to have a long service life, making it a cost-effective choice in the long run for airlines and operators.

In terms of technological innovation, the GE 206C1559P195 features integrated sensors that provide real-time data on engine performance. This capability allows for better monitoring and predictive maintenance, thereby increasing safety and reducing unscheduled downtimes.

Furthermore, the integration of digital twin technology enables operators to simulate different operational scenarios, improving decision-making and optimizing maintenance schedules. This technological edge places the GE 206C1559P195 at the forefront of aircraft engine component innovations, aligning with the industry's shift toward sustainability and efficiency.

In summary, the GE 206C1559P195 is a remarkable component that embodies GE's commitment to advance aviation technology, emphasizing performance, durability, and environmental awareness. Its design and technological features reflect the ongoing evolution in the aerospace industry, making it a key asset for modern aircraft engines.
Top Page Image Contents