Maytag W10366206A Reverse Door Standard Door optional, Replace Door and Hinges Standard Door

Page 7

3.Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4.Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

5.Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flat- blade screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

NOTE: The green, ground wire remains attached to the hinge.

6.Remove the parts for the left-hand side door top hinge as shown in the Top Hinge graphic. Lift the door from the bottom hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Reverse Door - Standard Door (optional)

IMPORTANT: If you want to reverse your door so it opens from the opposite side, follow these steps. If you are not reversing the door, see “Replace Door(s) and Hinges.”

Door Stop Screw

Door Handle Seal Screw Front

Flat-Head Handle Screw

Cabinet Hinge Hole Plug

Cabinet

1.Remove hinge screws from handle side and move them to opposite side. See Graphic 1-1.

2.Remove cabinet hinge hole plugs from cabinet top and move them to opposite side hinge holes as shown in Graphic 1-2.

Refrigerator door

1.Remove the refrigerator handle assembly as shown in Graphic 2. Keep all parts together.

2.Remove door handle seal screw front. Move to opposite side of refrigerator door as shown in Graphic 6.

3.Remove the door stop. Move it to the opposite side of the refrigerator door as shown in Graphic 4.

4.Attach the refrigerator handle to the opposite side of the refrigerator door.

NOTE: For models with front mount handles, replace the handle trim as shown in Graphic 2.

5.Tighten all screws. Set aside the door until hinges and freezer compartment door or drawer are in place.

Freezer door

1.Remove freezer handle assembly as shown. Keep all parts together. See Graphic 5-1.

2.Remove freezer door handle seal screw. Move to opposite side of freezer door.

3.Remove door stop. Move to opposite side of freezer door as shown. See Graphic 4.

4.Attach handle to opposite side of freezer door.

5.Tighten all screws. Set the door aside.

6.Remove the base grille by grasping the grille firmly with both hands and pulling it toward you.

NOTE: Place a shim under the bottom front edge of the refrigerator cabinet to take the weight off the roller brackets.

7.Remove the screws from both roller brackets. See Graphic 7.

8.Remove the hinge plate located behind the roller bracket and move it to the opposite side of the refrigerator. Move the hinge pin and shim to the outside hole on the hinge plate. See Graphic 7.

Replace Door and Hinges

Standard Door

NOTE: Graphics may be reversed if door swing is reversed.

Freezer drawer models

1.Replace the parts for the bottom hinge as shown. Tighten screws.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

2.Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten screws completely.

3.Adjust the door so that the bottom of the refrigerator door is aligned with the top of the freezer drawer. Tighten all screws.

Freezer door models

1.Make sure the hinge plate is securely fastened behind the roller bracket and that the hinge pin is inserted into the outside hole. Fully tighten all roller bracket screws.

2.Remove the shim that you placed under the front edge of the refrigerator cabinet. Replace the freezer door.

NOTE: Provide additional support for the door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working.

3.Assemble the parts for the center hinge as shown in the Center Hinge graphic, and tighten all the screws. Replace the refrigerator door.

4.Assemble the parts for the top hinge as shown in the Top Hinge graphic. Do not tighten the screws completely.

5.Adjust the doors so that the bottom of the refrigerator door is aligned with the top of the freezer door. Tighten all screws.

French Doors

1.Assemble the parts for the top hinges as shown in Top Hinge graphic. Do not tighten the screws completely.

2.Replace the parts for the bottom hinges as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator doors.

NOTE: Provide additional support for the refrigerator doors while the hinges are being moved. Do not depend on the door gasket magnets to hold the doors in place while you are working.

3.Align each door so that the bottom of the refrigerator door aligns evenly with the top of the freezer drawer. Tighten all screws.

4.Reconnect the wiring plug on top of the left-hand side refrigerator door.

5.Replace the top hinge covers.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Refrigerator User Instructions Refrigerator SafetyRemove the Packaging Installation InstructionsUnpack the Refrigerator Before You Throw Away Your Old Refrigerator or FreezerRecommended Grounding Method Clean Before UsingLocation Requirements Electrical RequirementsReverse Osmosis Water Supply Water Supply RequirementsConnect the Water Supply Water PressureConnect to Refrigerator Complete the InstallationStyle Remove Door and Hinges Standard Door Refrigerator Doors and DrawerRemove and Replace Refrigerator Door Handles Standard Door French DoorsRefrigerator door Reverse Door Standard Door optionalReplace Door and Hinges Standard Door CabinetReplace Drawer Front Remove and Replace Freezer DrawerRemove and Replace Drawer Handle Remove Drawer FrontStandard Door Door Removal Replacement Door Swing Reversal optionalDrawer Front Removal Drawer Front Replacement Door Closing and Door Alignment Refrigerator USEOpening and Closing Doors Electronic Controls Using the ControlsDigital Controls Reset Filter To Adjust Set Point TemperaturesAdditional Digital Control Center Features Fast Cool Door AlarmIce Maker Crisper Humidity ControlWater Dispenser Refrigerator Care CleaningWater Filtration System Changing the Light Bulb TroubleshootingRefrigerator Operation Ice and Water Temperature and MoistureWater from the dispenser is warm Water Filter CertificationsWater dispenser will not operate properly Water is leaking from the dispenser systemApplication Guidelines/Water Supply Parameters Performance Data SheetsModel UKF8001AXX-200 Capacity 200 Gallons 757 Liters This limited warranty does not cover Maytag Major Appliance WarrantyLimited Warranty Items Excluded from WarrantySécurité DU Réfrigérateur Instructions Dutilisation DU RéfrigérateurEnlèvement des matériaux d’emballage Instructions D’INSTALLATIONDéballage du réfrigérateur Avant de jeter votre vieux réfrigérateur ou congélateurMéthode recommandée de mise à la terre Exigences demplacementSpécifications électriques Raccordement à une canalisation d’eau Raccordement de la canalisation deauPression de leau Alimentation en eau par osmose inverseRaccordement au réfrigérateur Achever l’installationPorte à deux battants Portes et tiroir du réfrigérateurDépose des portes et des charnières Porte standard Porte du compartiment de congélation Réinstallation Porte et charnières Porte standardCaisse Porte du compartiment de réfrigérationPortes à deux battants Retirer et réinstaller le tiroir du congélateurDépose et réinstallation de la poignée du tiroir Réinstallation de la façade du tiroirPorte standard Inversion du sens douverture de la porte facultatifPortes à deux battants Charnières supérieuresFermeture et alignement de la porte Ouverture et fermeture des portes Utilisation des commandesCommandes électroniques Utilisation DU RéfrigérateurPour ajuster les points de réglage de température Commandes numériquesAjustement des réglages de commande Ajustement des réglages de commande numériquePréférences de lutilisateur avec la commande numérique Temp Alarm alarme de dépassement de températureDoor Alarm avertisseur de la porte Reset Filter réinitialisation du filtreTaux de production des glaçons Machine à glaçonsDistributeur d’eau Mise en marche/arrêt de la machine à glaçonsSystème de filtration de leau Entretien DU RéfrigérateurNettoyage Dépannage Remplacement de l’ampoule d’éclairageFonctionnement du réfrigérateur Glaçons et eau Température et humidité’eau coule du système de distribution Les glaçons sont creux ou petitsMauvais goût, odeur ou couleur grise des glaçons Le distributeur deau ne fonctionne pas correctementSystème de filtration d’eau intérieur Feuilles DE Données SUR LA PerformanceModèle UKF8001AXX-200 /Capacité 200 gallons 757 litres La présente garantie limitée ne couvre pas Garantie DE Gros Appareil Ménager MaytagGarantie Limitée Éléments Exclus DE LA GarantiePage Page Page Page W10366206A SP PN W10366207A

W10366206A specifications

The Maytag W10366206A is a highly regarded kitchen appliance, specifically designed as a replacement part for various Maytag appliances. This component showcases the brand's commitment to quality and durability, ensuring that it meets the demanding needs of everyday use in modern kitchens.

One of the standout features of the W10366206A is its robust construction. Made with high-quality materials, it is engineered to withstand the rigors of frequent operation, contributing to the longevity of the appliance it serves. This durability is a hallmark of Maytag, a brand known for its emphasis on reliability and performance.

The W10366206A is compatible with a range of Maytag models, which adds to its appeal. This versatility allows consumers to replace worn or damaged parts without the need to purchase an entirely new appliance. This not only saves money but also reduces waste, aligning with sustainable practices that many consumers value today.

In terms of technology, the W10366206A embodies innovative design. This part is designed with precision to ensure a seamless fit and effective operation within your kitchen appliance. Its design includes features that facilitate easy installation, making it a user-friendly option for those who might prefer to make repairs themselves.

Another important characteristic of the W10366206A is its efficiency. By ensuring that appliances operate at their optimal levels, this replacement part contributes to energy savings, which is increasingly important in today’s eco-conscious environment. With energy-efficient performance, consumers can expect to see reductions in utility bills while enjoying consistent service from their Maytag appliances.

Moreover, Maytag's commitment to customer satisfaction is evident in the extensive testing and quality control that the W10366206A undergoes before reaching consumers. This rigorous process ensures that every part meets high standards of performance, giving users peace of mind in their investment.

In conclusion, the Maytag W10366206A presents a combination of durability, compatibility, innovative technology, and efficiency that make it a valuable component in any kitchen setting. Whether you are looking to maintain your appliance’s performance or make a simple upgrade, this replacement part stands as a testament to Maytag’s reputation for excellence. Investing in the W10366206A is choosing reliability and quality that consumers can trust.
Top Page Image Contents