GE 200D9366P016 About the freezer, Instructions Installation, Freezer Shelves and Baskets

Page 11

About the freezer.

GEAppliances.com

Not all features are on all models.

 

Freezer Shelves and Baskets

 

A shelf above the ice storage bin

NOTE: Do not fill baskets higher than the rim

A half-widthbasket

of the basket. This may cause baskets to stick

or jam when opening or closing.

 

A shallowfull-width basket

 

A deep full-width basket

 

Appearance and features may vary

Safety Instructions Operating

Appearance may vary

Appearance may vary

Basket Removal

To remove the deep full-widthbasketon freezer drawer models:

Open the freezerdraweruntil it stops.

The freezer basket rests on the inside tabson the drawer slides.

Lift the basket so that it is out of all 6 slidebracket tabs.

Tilt the basket and lift out of the drawer.

To remove the half-widthbasket:

Pull the basketout to the stop location.

Lift the basket up at the front to release it from the slides.

Lift the back up and out of the slide.

To remove the shallow full-widthbasket:

Pull the basketout to the stop location.

Lift the front up and over the stop location.

Whenreplacing the deep full-width basket:

Tilt the basket back and lower it down into the drawer. Rotate the basket to a horizontal position and press it down into the 6 alignment tabs.

NOTE: Always be surethat the basket is seated in all 6 slide bracket tabs before sliding back into the freezer.The basket can be turned in either direction frontto back and installed into the freezer.

Whenreplacing the basket, make surethat the wire tabs and wire hookson the sides of the basket go into the slots in the top

of the upper basket slides.

NOTE: Always be sureto fully close this basket.

Lift the basket up and out.

Instructions

Instructions

Installation

Troubleshooting Tips

Appearance may vary

11

Consumer Support

Image 11
Contents Write the model and serial numbers here Model # Serial # GEAppliances.comRefrigerator or Freezer Operating Instructions InstallationConsumer Support Troubleshooting Tips Before You Throw Away Your OldGEAppliances.com Operating InstructionsChanging the Temperature About the controls with temperature settingsInstallation Instructions Tips Consumer Support TroubleshootingHow it Works SafetyAbout Door Alarm on some models About TurboCool. on some modelsFilter Bypass Plug When to Replace the FilterInstalling the Filter Cartridge Water Filter CartridgeDo not overtighten About the water filter. on 20 models onlyConsumer Support Installation InstructionsTroubleshooting Tips About the shelves and binsShelf Saver Rack on some models About the additionalfeaturesAdjustable Bins on the Door Instructions Operating Non-Adjustable Bins on the DoorFruit and Vegetable Crisper Adjustable Humidity Crisper on some modelsAdjustable Temperature Deli Pan About the crispersand pansBasket Removal Instructions InstallationAbout the freezer Freezer Shelves and BasketsAutomatic Icemaker on some models Accessing Ice and Reaching the Power SwitchIcemaker Accessory Kit About the automatic icemakerCleaning the Inside Care and cleaning of the refrigeratorCleaning the Outside Preparing to Move Care and cleaningof the refrigerator.Behind the Refrigerator Preparing for VacationFreezer Light Replacing the light bulbsInstructions Operating Refrigerator LightsRead these instructions completely and carefully Before YOU BeginPreparation Tools YOU MAY NeedClearances Connecting the Refrigerator To the House Water LineRefrigerator Location PUT the Refrigeratorin Place Icemaker-Installed ModelsTurn on the Water Supply Plug in the RefrigeratorStainless steel and plastic handles Remove the Fresh Food Door HandleStainless steel on Some models Plastic handle on some modelsPlastic handle Attach the Fresh Food Door HandleStainless steel handle Refrigerator, counterclockwise to lower it SET the ControlsLeveling legs have 2 purposes Remove the Base Grille Remove the BasketAttach and Secure the Drawer Front to the Slides Two people may be required to complete this procedureReplace the Freezer Basket Tools YOU will Need Important NotesRemove Center Hinge Installcenter HingeRehang Refrigeratordoor Install the Logo BadgeRemoving the DOORSDouble Door Refrigerator Models only Remove Freezer Drawer Remove Opposite DoorReplace Freezer Drawer Rehang RefrigeratordoorsReplace Opposite Door Align Double DoorsWhat YOU will Need Installing the Waterline Icemaker ModelsTake care not to allow water to drain into the drill Shut OFF the Main Water SupplyChoose the Valve Location Drill the Hole for the ValveFlush OUT the Tubing Fasten the Shutoff ValveTighten the Pipe Clamp Route the TubingNormal operatingsounds Before you callfor service…Safety Instructions Operating Instructions Installation Safety Instructions Before you call for service…Odor to refrigerator Pops open when Open, the freezer door/drawerIce cubes have Food transmitting odor/taste Slow ice cube freezing Door left openOperating Instructions Safety Instructions Installation When opening or Light remains red Be resetRefrigerator beeping This is the door alarm Control setting isInstructions Ownership Registration Page What GE Will Not Cover Safety Instructions Operating InstructionsFor The Period GE Will Replace Customer Warranty Special Notices Performance Data SheetOperating Specifications General Installation/Operation/Maintenance RequirementsStandardNo Aesthetic Effects Water Treatment Device Water Treatment Device Certificate Number

200D9366P016 specifications

The GE 200D9366P016 is a notable component within General Electric's (GE) expansive portfolio, particularly recognized for its application in industrial environments requiring robust and reliable performance. This function-oriented device is often employed in various sectors, including power generation, oil and gas, and manufacturing, where operational efficiency and precision are paramount.

One of the primary features of the GE 200D9366P016 is its exceptional durability. Constructed to withstand harsh operating conditions, it is engineered with high-quality materials that resist wear and tear. This durability not only extends the lifespan of the component but also reduces maintenance needs, allowing for longer intervals between service checks, thus saving both time and money for users.

The GE 200D9366P016 incorporates advanced technologies designed to enhance efficiency. It is often embedded with smart sensing capabilities that facilitate real-time monitoring of operational parameters. This feature enables users to track performance metrics, detect potential failures before they escalate, and optimize operational workflows.

In addition to its advanced sensing technologies, the GE 200D9366P016 is designed for seamless integration with a wide range of industrial systems. This interoperability is crucial for facilities that utilize various GE products or require compatibility with third-party systems. The component's design ensures that it can be easily adapted to different configurations, thereby enabling users to customize solutions based on specific operational requirements.

The product’s user-friendly interface is another significant characteristic, allowing operators to easily interact with the device and access critical data and controls. Clear displays, coupled with intuitive controls, enable quick and efficient operation, minimizing the learning curve for new users.

Moreover, the GE 200D9366P016 is backed by extensive technical support and documentation from GE, enhancing user confidence in installation and operation. Clients benefit from a wealth of resources, including troubleshooting guides and user manuals, ensuring that they can maximize the utility of the component.

Overall, the GE 200D9366P016 stands out for its robust construction, advanced technological integration, seamless compatibility, and user-centric design, making it a preferred choice for industries that prioritize reliability and efficiency in their operations.