GE 200D9366P016 Turn on the Water Supply, Plug in the Refrigerator, PUT the Refrigeratorin Place

Page 18

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

1CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(cont.)

AIf you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing.

BIf you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect™ tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

CFasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

One of the illustrations below will look like the connection on your refrigerator.

Icemaker-Ready models

Tubing

1/4″ Copper

Tubing

Clamp

 

1/4″ Compression Nut

Ferrule (sleeve)

Refrigerator

ConnectionSmartConnect™

Tubing

Icemaker-Installed Models

Ferrule 1/4″

Refrigerator (sleeve) Compression

Connection Nut

SmartConnect™

Tubing

1/4″ Tubing

Tubing Clamp

18

2TURN ON THE WATER SUPPLY

(icemaker and dispenser models)

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

3PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.

See the grounding information attached to the power cord.

4PUT THE REFRIGERATORIN PLACE

Move the refrigerator to its final location.

5LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmly positioned on the floor, and the front is raised just enough that the door closes easily when opened about halfway.

To adjust the leveling legs, turn the legs clockwise to raise the refrigerator, counterclockwise to lower it.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents GEAppliances.com Write the model and serial numbers here Model # Serial #Before You Throw Away Your Old Operating Instructions InstallationConsumer Support Troubleshooting Tips Refrigerator or FreezerOperating Instructions GEAppliances.comConsumer Support Troubleshooting About the controls with temperature settingsInstallation Instructions Tips Changing the TemperatureAbout TurboCool. on some models SafetyAbout Door Alarm on some models How it WorksWater Filter Cartridge When to Replace the FilterInstalling the Filter Cartridge Filter Bypass PlugAbout the water filter. on 20 models only Do not overtightenAbout the shelves and bins Installation InstructionsTroubleshooting Tips Consumer SupportInstructions Operating Non-Adjustable Bins on the Door About the additionalfeaturesAdjustable Bins on the Door Shelf Saver Rack on some modelsAbout the crispersand pans Adjustable Humidity Crisper on some modelsAdjustable Temperature Deli Pan Fruit and Vegetable CrisperFreezer Shelves and Baskets Instructions InstallationAbout the freezer Basket RemovalAbout the automatic icemaker Accessing Ice and Reaching the Power SwitchIcemaker Accessory Kit Automatic Icemaker on some modelsCare and cleaning of the refrigerator Cleaning the OutsideCleaning the Inside Preparing for Vacation Care and cleaningof the refrigerator.Behind the Refrigerator Preparing to MoveRefrigerator Lights Replacing the light bulbsInstructions Operating Freezer LightTools YOU MAY Need Before YOU BeginPreparation Read these instructions completely and carefullyConnecting the Refrigerator To the House Water Line Refrigerator LocationClearances Plug in the Refrigerator Icemaker-Installed ModelsTurn on the Water Supply PUT the Refrigeratorin PlacePlastic handle on some models Remove the Fresh Food Door HandleStainless steel on Some models Stainless steel and plastic handlesAttach the Fresh Food Door Handle Stainless steel handlePlastic handle SET the Controls Leveling legs have 2 purposesRefrigerator, counterclockwise to lower it Remove the Basket Remove the Base GrilleTwo people may be required to complete this procedure Replace the Freezer BasketAttach and Secure the Drawer Front to the Slides Important Notes Tools YOU will NeedInstallcenter Hinge Remove Center HingeInstall the Logo Badge Rehang RefrigeratordoorRemoving the DOORSDouble Door Refrigerator Models only Remove Opposite Door Remove Freezer DrawerAlign Double Doors Rehang RefrigeratordoorsReplace Opposite Door Replace Freezer DrawerInstalling the Waterline Icemaker Models What YOU will NeedDrill the Hole for the Valve Shut OFF the Main Water SupplyChoose the Valve Location Take care not to allow water to drain into the drillRoute the Tubing Fasten the Shutoff ValveTighten the Pipe Clamp Flush OUT the TubingBefore you callfor service… Safety Instructions Operating Instructions InstallationNormal operatingsounds Before you call for service… Safety InstructionsSlow ice cube freezing Door left open Pops open when Open, the freezer door/drawerIce cubes have Food transmitting odor/taste Odor to refrigeratorOperating Instructions Safety Instructions Installation Control setting is Light remains red Be resetRefrigerator beeping This is the door alarm When opening orInstructions Ownership Registration Page Safety Instructions Operating Instructions For The Period GE Will ReplaceWhat GE Will Not Cover Customer Warranty General Installation/Operation/Maintenance Requirements Performance Data SheetOperating Specifications Special NoticesStandardNo Aesthetic Effects Water Treatment Device Water Treatment Device Certificate Number

200D9366P016 specifications

The GE 200D9366P016 is a notable component within General Electric's (GE) expansive portfolio, particularly recognized for its application in industrial environments requiring robust and reliable performance. This function-oriented device is often employed in various sectors, including power generation, oil and gas, and manufacturing, where operational efficiency and precision are paramount.

One of the primary features of the GE 200D9366P016 is its exceptional durability. Constructed to withstand harsh operating conditions, it is engineered with high-quality materials that resist wear and tear. This durability not only extends the lifespan of the component but also reduces maintenance needs, allowing for longer intervals between service checks, thus saving both time and money for users.

The GE 200D9366P016 incorporates advanced technologies designed to enhance efficiency. It is often embedded with smart sensing capabilities that facilitate real-time monitoring of operational parameters. This feature enables users to track performance metrics, detect potential failures before they escalate, and optimize operational workflows.

In addition to its advanced sensing technologies, the GE 200D9366P016 is designed for seamless integration with a wide range of industrial systems. This interoperability is crucial for facilities that utilize various GE products or require compatibility with third-party systems. The component's design ensures that it can be easily adapted to different configurations, thereby enabling users to customize solutions based on specific operational requirements.

The product’s user-friendly interface is another significant characteristic, allowing operators to easily interact with the device and access critical data and controls. Clear displays, coupled with intuitive controls, enable quick and efficient operation, minimizing the learning curve for new users.

Moreover, the GE 200D9366P016 is backed by extensive technical support and documentation from GE, enhancing user confidence in installation and operation. Clients benefit from a wealth of resources, including troubleshooting guides and user manuals, ensuring that they can maximize the utility of the component.

Overall, the GE 200D9366P016 stands out for its robust construction, advanced technological integration, seamless compatibility, and user-centric design, making it a preferred choice for industries that prioritize reliability and efficiency in their operations.
Top Page Image Contents