GE 200D9366P016 About the controls with temperature settings, Installation Instructions Tips

Page 4

Operating Instructions Safety Instructions

Installation

Instructions

Tips

About the controls with temperature settings.

(on some models)

(on some models)

NOTE: The refrigerator is shipped with protectivefilm covering the temperature controls. If this film was not removed duringinstallation, remove it now.

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Consumer Support Troubleshooting

 

Changing the Temperature

 

For Controls-on-the-Door Models:

 

To changethe temperature,pressand release the

 

WARMER or COLDER pad. The ACTUALTEMP light

 

willcome on and the displaywill show the actual

 

temperature. To change the temperature, tap either

 

the WARMER or COLDER pad until the desired

 

temperature is displayed.

 

For Controls Inside the Refrigerator:

 

Opening the door displays the actualtemperature.

 

To change the temperature, press either the

 

WARMER or COLDER touch pads untilthe

 

desired temperature is displayed.

 

Once the desired temperature has been set,

 

the temperature displaywillreturn to the actual

4

refrigerator and freezer temperatures after 5 seconds.

Several adjustments may be required.

 

Each time you adjust controls, allow 24 hours for the refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad for either the refrigerator or the freezer until the display shows OFF. To turn the unit back on, press the COLDER pad for either the refrigerator or freezer. Then press the COLDER pad again and it will go to the preset points of 0°F for the freezer and 37°F for the refrigerator.Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents GEAppliances.com Write the model and serial numbers here Model # Serial #Operating Instructions Installation Consumer Support Troubleshooting TipsBefore You Throw Away Your Old Refrigerator or FreezerOperating Instructions GEAppliances.comAbout the controls with temperature settings Installation Instructions TipsConsumer Support Troubleshooting Changing the TemperatureSafety About Door Alarm on some modelsAbout TurboCool. on some models How it WorksWhen to Replace the Filter Installing the Filter CartridgeWater Filter Cartridge Filter Bypass PlugAbout the water filter. on 20 models only Do not overtightenInstallation Instructions Troubleshooting TipsAbout the shelves and bins Consumer SupportAbout the additionalfeatures Adjustable Bins on the DoorInstructions Operating Non-Adjustable Bins on the Door Shelf Saver Rack on some modelsAdjustable Humidity Crisper on some models Adjustable Temperature Deli PanAbout the crispersand pans Fruit and Vegetable CrisperInstructions Installation About the freezerFreezer Shelves and Baskets Basket RemovalAccessing Ice and Reaching the Power Switch Icemaker Accessory KitAbout the automatic icemaker Automatic Icemaker on some modelsCleaning the Outside Care and cleaning of the refrigeratorCleaning the Inside Care and cleaningof the refrigerator. Behind the RefrigeratorPreparing for Vacation Preparing to MoveReplacing the light bulbs Instructions OperatingRefrigerator Lights Freezer LightBefore YOU Begin PreparationTools YOU MAY Need Read these instructions completely and carefullyRefrigerator Location Connecting the Refrigerator To the House Water LineClearances Icemaker-Installed Models Turn on the Water SupplyPlug in the Refrigerator PUT the Refrigeratorin PlaceRemove the Fresh Food Door Handle Stainless steel on Some modelsPlastic handle on some models Stainless steel and plastic handlesStainless steel handle Attach the Fresh Food Door HandlePlastic handle Leveling legs have 2 purposes SET the ControlsRefrigerator, counterclockwise to lower it Remove the Basket Remove the Base GrilleReplace the Freezer Basket Two people may be required to complete this procedureAttach and Secure the Drawer Front to the Slides Important Notes Tools YOU will NeedInstallcenter Hinge Remove Center HingeInstall the Logo Badge Rehang RefrigeratordoorRemoving the DOORSDouble Door Refrigerator Models only Remove Opposite Door Remove Freezer DrawerRehang Refrigeratordoors Replace Opposite DoorAlign Double Doors Replace Freezer DrawerInstalling the Waterline Icemaker Models What YOU will NeedShut OFF the Main Water Supply Choose the Valve LocationDrill the Hole for the Valve Take care not to allow water to drain into the drillFasten the Shutoff Valve Tighten the Pipe ClampRoute the Tubing Flush OUT the TubingSafety Instructions Operating Instructions Installation Before you callfor service…Normal operatingsounds Before you call for service… Safety InstructionsPops open when Open, the freezer door/drawer Ice cubes have Food transmitting odor/tasteSlow ice cube freezing Door left open Odor to refrigeratorOperating Instructions Safety Instructions Installation Light remains red Be reset Refrigerator beeping This is the door alarmControl setting is When opening orInstructions Ownership Registration Page For The Period GE Will Replace Safety Instructions Operating InstructionsWhat GE Will Not Cover Customer Warranty Performance Data Sheet Operating SpecificationsGeneral Installation/Operation/Maintenance Requirements Special NoticesStandardNo Aesthetic Effects Water Treatment Device Water Treatment Device Certificate Number

200D9366P016 specifications

The GE 200D9366P016 is a notable component within General Electric's (GE) expansive portfolio, particularly recognized for its application in industrial environments requiring robust and reliable performance. This function-oriented device is often employed in various sectors, including power generation, oil and gas, and manufacturing, where operational efficiency and precision are paramount.

One of the primary features of the GE 200D9366P016 is its exceptional durability. Constructed to withstand harsh operating conditions, it is engineered with high-quality materials that resist wear and tear. This durability not only extends the lifespan of the component but also reduces maintenance needs, allowing for longer intervals between service checks, thus saving both time and money for users.

The GE 200D9366P016 incorporates advanced technologies designed to enhance efficiency. It is often embedded with smart sensing capabilities that facilitate real-time monitoring of operational parameters. This feature enables users to track performance metrics, detect potential failures before they escalate, and optimize operational workflows.

In addition to its advanced sensing technologies, the GE 200D9366P016 is designed for seamless integration with a wide range of industrial systems. This interoperability is crucial for facilities that utilize various GE products or require compatibility with third-party systems. The component's design ensures that it can be easily adapted to different configurations, thereby enabling users to customize solutions based on specific operational requirements.

The product’s user-friendly interface is another significant characteristic, allowing operators to easily interact with the device and access critical data and controls. Clear displays, coupled with intuitive controls, enable quick and efficient operation, minimizing the learning curve for new users.

Moreover, the GE 200D9366P016 is backed by extensive technical support and documentation from GE, enhancing user confidence in installation and operation. Clients benefit from a wealth of resources, including troubleshooting guides and user manuals, ensuring that they can maximize the utility of the component.

Overall, the GE 200D9366P016 stands out for its robust construction, advanced technological integration, seamless compatibility, and user-centric design, making it a preferred choice for industries that prioritize reliability and efficiency in their operations.
Top Page Image Contents