Amana Bottom Mount Refrigerator service manual Water Connection, Door Panel Installation

Page 7

Installation Instructions

Water Connection

The garden hose fitting, compression nut, and sleeve are located in the literature packet. Amana® Clean 'n Clear ™ Bayonet Style Water Filtration System WF60 is shipped in crisper drawer. See water filter installation and operating instructions for specifics.

1.Flush air and impurities from water line by turning on water supply and running a pint or more of water into a bucket.

2.Remove plastic cap from water valve fitting. Connect copper tubing to water valve with brass nut and brass sleeve. Insert copper tubing completely into water valve inlet port. Connect brass nut on copper tubing to water valve inlet port fitting. Confirm copper tubing is secure by pulling on copper tubing.

3.Turn on water supply to refrigerator and check f o r leaks. Turn off water supply to refrigerator and correct any leaks. Repeat this process until no leaks exist. Completely turn on water supply to refrigerator.

4.Verify drain pan is installed and aligned.

5.Replace toe grille with air vents to the top. Kitchen flooring must allow toe grille to be removed. See "Installation Specifications" for height clearance. See "Custom Finishing Options" when using a custom toe grille.

Air vents

Door Panel Installation

Panels must not weigh more than 50 pounds per door.

Refrigerator Door 3/4" Raised Panel

1.Slide out handle screw insert and remove handle by removing screws with a Phillips screwdriver.

Handle

Handle screw insert

Screws

Refrigerator Door

 

2.

Align panel brackets (supplied) with center edge

 

Clip

of panel. Install brackets using 1/4" screws

 

 

(supplied).

 

3.

If base panel is less than 1/4" use plastic

 

 

shims (supplied). Shims go between bracket and

Toe grille

 

wood to space panels to desired depth.

4.

Drive low profile screws (supplied) with

 

 

 

Phillips screwdriver.

 

 

• Panel brackets must be exactly flush to 1/16"

 

 

inboard of panel edge.

 

 

• For ease of panel installation 2 people are

 

 

required to lift and guide panel into trim.

 

 

• Install 1 panel at a time.

 

5.

Align panel in trim and push evenly. For

 

 

smoother installation apply bar soap on door

 

 

trim and refrigerator trim. If panel binds loosen

 

 

top or side door trim. Adjust panel and retighten.

 

6.

Install handle with screws. Install screw strip

 

 

(supplied) by starting in one corner and pushing

 

 

the length of the strip down.

November 1996

7

RS1200001

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Bottom Mount Refrigerators ServiceGrounding Information Safety and Electrical InformationSafety Symbols, Words, and Labels Electrical RequirementsContents Ice Maker Uncrating Installation InstructionsSecuring Installation Instructions Water Connection Door Panel InstallationRefrigerator Door 3/4 Raised Panel Freezer Door 3/4 Raised Panel Door Stop AdjustmentHinge Adjustment Interior SetupNormal Operating Sounds Sound InformationFreezer and fresh food fan air rushes and whirs System Diagnosis Pressure and Relationship ChartRefrigerant Shortage Symptoms Refrigerant Overcharge SymptomsRestriction Symptoms Low or High Ambient Temperature Installation Symptoms Air in System SymptomsHeat Load Symptoms Health, Safety, and Handling HFC134a Service InformationComparison of CFC12 and HFC134a Properties Drier Replacement Service EquipmentRefrigerant Charge Replacement Service CompressorCompressor Testing Procedures Leak TestingHFC134a Service Information Refrigerant Flow Air Flow Machine Compartment Assembly Component Function and Testing April RS1200001 Rev.1 Switch Continuity Functions Test Dpst Component Function and Testing Electronic Functional Description Keyboard Functions Electronic Testing ModeTemperature Control Operation Accessing Program Mode Power Up ConditionEeprom Update in Control Memory Factory set freezer and refrigerator settingsMode B Functions Mode a Functions Freezer or Refrigerator TemperatureOperation Exiting Program Mode Electronic Functional Description VAC Adaptive Defrost Circuitry CircuitryFreezer Compartment Refrigeration Cycle Circuitry Fresh Food Compartment Refrigeration Cycle CircuitryDoor Disassembly Procedures Cabinet Components Disassembly Procedures Refrigerator Thermistor Chefs Pantry AssemblyCondensate Drain Pan Shelf Support LaddersMachine Compartment Disassembly Procedures Showroom Switch Power Disconnect SwitchCondenser Typical External Sweat Pattern Problem Possible Cause Troubleshooting GuideTroubleshooting Guide Operation SpecificationsTesting Procedures Ice MakerDisassembly Procedures Accessing Control Box Water Fill AdjustmentEjector Blades or Stripper Thermostat Water ProblemsWiring Harness Temperature ProblemsWater Valve No or Low Ice Production Problem Action Ice Maker Troubleshooting ChartEjector Position Excessive Ice Production Ice Maker Wiring Diagram and Parts Layout B136CKR1 Introduction Recognize this symbol as a safety precautionParts List B136CKR1 and B136CKL1 Custom Handle KitDoor Panels with Hinge on Right Side and Extruded Handle Panel DimensionsRefrigerator, Freezer Door Panel with Custom Handle inches 780 892 Radius 563 780 892 Radius 563 Freezer Drawer ProceduresB136CKR1 and B136CKL1 Custom Handle Kit B136SPK1 ¼ Facia Front Enclosure Kit Panel minimum depth Minimum height Side.186 Location of Panel Brackets on Side PanelsB136SPK1 ¼ Facia Front Enclosure Kit Procedures Bottom cabinet Panel Extrusion B136SPK1 ¼ Facia Front Enclosure Kit B136SPK2 ¾ Side Panel Kit Panel Dimensions Side view 11.281 500 062 Front Bottom Panel Bracket Front Panel Bracket Bottom RS1200001 November Procedure B136SPK2 ¾ Side Panel Kit
Top Page Image Contents