Bally Refrigerated Boxes Refrigerators/Freezers/Warmers Removal of Doors and Door Adjustment

Page 9

REMOVAL OF DOORS AND DOOR ADJUSTMENT

During installation, it may become necessary to remove the cabinet doors to facilitate passage through narrow doorways or hallways. To remove a door, pry off all hinge covers using a sharp tool or knife (see figure 5). Swing the door to the open-door position (90 degrees) and carefully lift the door upward, removing the door from the hinge bodies. If it is necessary to remove the hinge bodies from the cabinet face, be extremely careful not to lose the light switch pin located inside all top hinge bodies. To reinstall the door, reverse the above procedure.

All doors have been aligned at the factory, however vibration during transportation may cause doors to shift and realignment may be necessary. If the door(s)

require realignment, proceed as follows:

1.Pry off all hinge covers using a sharp tool or knife.

2.For each door, loosen the screws which secure the hinge bodies to the cabinet face and slide the door into alignment. Hold the door firmly in place and tighten all screws securely.

If the door gasket(s) do not seal properly to the cabinet face and there are gaps between the gasket and the face on the hinge edge, proceed as follows:

1.For each door, loosen all screws which are directed into the edge of the door and push the door towards the cabinet eliminating the gap. Hold the door firmly in place and tighten all screws securely.

2.Replace all snap-on hinge covers.

FIGURE 5

DOOR ADJUSTMENT AND REMOVAL

- 7 -

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Reach-In and Roll-In Operators Manual Table of Contents General Information and Important Operating Facts Receiving Your NEW ModelInstallation and Location Clearances Uncrating Your NEW ModelVentilation Floor Loads Minimum Clearance DimensionsInstalling Legs and Leveling REACH-IN Models LEG InstallationMounting ROLL-IN Models in Place and Leveling Casters Must be Tight to Cabinet Bottom Installing Casters and Leveling REACH-IN ModelsCondensate Evaporator Installation Installing Condensate EvaporatorDoor Adjustment and Removal Removal of Doors and Door AdjustmentRemoval of Grill Initial Cleaning ProcedureSTART-UP Procedure Electrical Connections VOLT, 60 HZ, 1 Phase ConnectionSpecial Voltage Connections Remote Applications START-UP ChecklistThermometer Calibration OperationCalibration Check Dial ThermometerThermometer Calibration Refrigerator and Freezer Thermostat Refrigerator System and AdjustmentDefrost Operation Freezer System and AdjustmentDefrost Timer Setting Warmer System and Adjustment LOW-PROFILE,CEILING-MOUNT Evaporator Assembly Evaporator AssemblyPLUG-TYPE,TOP-MOUNT Evaporator Assembly PLUG-TYPE,TOP-MOUNT Evaporator AssemblyStandard Pilaster Interior REACH-IN AccessoriesOptional HEAVY-DUTY Pilaster Optional Angle PAN Slides Optional Interior AccessoriesSafety Precautions Maintenance Periodic Cleaning ProcedureSliding and Hinged Glass General Preventative MaintenanceParts and Service Condensing unit will But short cycles on Problem Probable Cause CorrectionProduct zone Wiring Diagrams Page Page Page Page Page Page

Refrigerators/Freezers/Warmers specifications

Bally Refrigerated Boxes is a prominent name in the realm of commercial refrigeration, specializing in high-quality refrigerators, freezers, and warmers designed for a variety of food service environments. With a commitment to innovation and efficiency, Bally’s products cater to the needs of restaurants, catering businesses, and food retailers, ensuring that perishable goods are stored at optimal temperatures while maintaining quality.

One of the standout features of Bally Refrigerated Boxes is their versatility. Their product line includes reach-in refrigerators and freezers, undercounter units, and pass-through models, allowing businesses to choose the best fit for their kitchen layout and operational requirements. This versatility is complemented by a variety of sizes and configurations, enabling users to maximize storage space while keeping products accessible.

Energy efficiency is a central focus of Bally’s design philosophy. Many models are equipped with advanced insulation technology and energy-efficient compressors, which significantly reduce energy consumption without compromising performance. This not only leads to lower operational costs but also aligns with modern sustainability goals, helping businesses minimize their environmental footprint.

Bally Refrigerated Boxes also incorporate state-of-the-art temperature control systems. These units often feature digital temperature displays, which allow for precise monitoring and easy adjustments. Some models are equipped with smart technology that can send alerts in case of temperature fluctuations, ensuring that products are always kept within safe limits.

Durability is another hallmark of Bally products. Constructed from high-quality stainless steel, both the interiors and exteriors are designed to withstand the rigorous demands of commercial kitchens. This material not only enhances the longevity of the units but also makes them easy to clean, promoting hygiene in food storage environments.

Moreover, user-friendly designs are a priority, with thoughtfully arranged interior shelving options that cater to various product sizes and shapes. The user experience is enhanced with features such as LED lighting, which provides excellent visibility while being energy-efficient.

In conclusion, Bally Refrigerated Boxes' refrigerators, freezers, and warmers are built to deliver on performance, efficiency, and durability. With a wide range of options tailored to commercial needs, their innovative technology and design characteristics make them a reliable choice for any food service operation. Professionals in the industry can trust Bally to not only meet but exceed their refrigeration and warming requirements, ensuring that food safety and quality remain paramount.
Top Page Image Contents