Bally Refrigerated Boxes Refrigerators/Freezers/Warmers Uncrating Your NEW Model, Ventilation

Page 4

UNCRATING YOUR NEW MODEL

The shipping container should remain on your model as protection against dents or scratches while transporting it to the actual set-up location. Remove the shipping container only at the last possible moment by following these simple steps:

1.Using a pry bar, pry off and remove crate end bottom staples.

2.Pry off and remove crate front and rear bottom staples.

3.Slide crate upward and remove it, being careful not to rub against cabinet. There are up to four (4) bolts securing the cabinet to the wooden skid. The bolts are located at each end on the underside of the skid. In order to remove these bolts it is advisable to tilt the cabinet backwards and place wooden blocks at each end in order to hold it in its tilted position. Using a 3/4" socket or open end wrench, remove the bolts and carefully slide the model off of the skid. After skid removal, the cabinet should never be moved without dollies or rollers to avoid damage to the cabinet bottom or floor.

Important Note: Do not under any circumstances lay your new model on its front or sides. Only for a brief period, may you lay the model on its back and only then, when its properly blocked so as not to crush the condensate drain tubing and also to allow provision for your hands in order to set it in its upright position without inflicting damage to the cabinet. Do not plug in and operate model for at least three (3) hours after cabinet is set upright from being on its back as damage could result to the compressor.

INSTALLATION AND LOCATION

CLEARANCES

Before moving the cabinet to its final point of installation, accurately measure all doorways or passages to assure clearance. If additional clearance is needed, cabinet doors and grill can be easily removed (see instructions outlined in "removal of doors" and "removal of grill" sections).

VENTILATION

The final location site of your air cooled refrigerator or freezer must be able to provide a large quantity of cool, clean air. The refrigeration system operates most efficiently and trouble-free with cool, dry air circulation. Avoid locations near heat and moisture generating equipment such as stoves, ovens, cooking ranges, fryers, dish washers, steam kettles, etc., and also direct sunlight where temperatures can be in excess of 100 degrees f. Also, do not select a location in an unheated room or area where temperatures may drop below 55 degrees f. Air supply to the condensing unit is equally important. Restricting the air supply will place an excessive heat load on the condensing unit and adversely effect its operating efficiency.

- 2 -

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Reach-In and Roll-In Operators Manual Table of Contents Receiving Your NEW Model General Information and Important Operating FactsUncrating Your NEW Model Installation and Location ClearancesVentilation Minimum Clearance Dimensions Floor LoadsLEG Installation Installing Legs and Leveling REACH-IN ModelsMounting ROLL-IN Models in Place and Leveling Installing Casters and Leveling REACH-IN Models Casters Must be Tight to Cabinet BottomInstalling Condensate Evaporator Condensate Evaporator InstallationRemoval of Doors and Door Adjustment Door Adjustment and RemovalInitial Cleaning Procedure Removal of GrillVOLT, 60 HZ, 1 Phase Connection START-UP Procedure Electrical ConnectionsSpecial Voltage Connections START-UP Checklist Remote ApplicationsOperation Thermometer CalibrationCalibration Check Dial ThermometerThermometer Calibration Refrigerator System and Adjustment Refrigerator and Freezer ThermostatFreezer System and Adjustment Defrost OperationDefrost Timer Setting Warmer System and Adjustment Evaporator Assembly LOW-PROFILE,CEILING-MOUNT Evaporator AssemblyPLUG-TYPE,TOP-MOUNT Evaporator Assembly PLUG-TYPE,TOP-MOUNT Evaporator AssemblyInterior REACH-IN Accessories Standard PilasterOptional Interior Accessories Optional HEAVY-DUTY Pilaster Optional Angle PAN SlidesMaintenance Periodic Cleaning Procedure Safety PrecautionsGeneral Preventative Maintenance Sliding and Hinged GlassParts and Service Condensing unit will Problem Probable Cause Correction But short cycles onProduct zone Wiring Diagrams Page Page Page Page Page Page

Refrigerators/Freezers/Warmers specifications

Bally Refrigerated Boxes is a prominent name in the realm of commercial refrigeration, specializing in high-quality refrigerators, freezers, and warmers designed for a variety of food service environments. With a commitment to innovation and efficiency, Bally’s products cater to the needs of restaurants, catering businesses, and food retailers, ensuring that perishable goods are stored at optimal temperatures while maintaining quality.

One of the standout features of Bally Refrigerated Boxes is their versatility. Their product line includes reach-in refrigerators and freezers, undercounter units, and pass-through models, allowing businesses to choose the best fit for their kitchen layout and operational requirements. This versatility is complemented by a variety of sizes and configurations, enabling users to maximize storage space while keeping products accessible.

Energy efficiency is a central focus of Bally’s design philosophy. Many models are equipped with advanced insulation technology and energy-efficient compressors, which significantly reduce energy consumption without compromising performance. This not only leads to lower operational costs but also aligns with modern sustainability goals, helping businesses minimize their environmental footprint.

Bally Refrigerated Boxes also incorporate state-of-the-art temperature control systems. These units often feature digital temperature displays, which allow for precise monitoring and easy adjustments. Some models are equipped with smart technology that can send alerts in case of temperature fluctuations, ensuring that products are always kept within safe limits.

Durability is another hallmark of Bally products. Constructed from high-quality stainless steel, both the interiors and exteriors are designed to withstand the rigorous demands of commercial kitchens. This material not only enhances the longevity of the units but also makes them easy to clean, promoting hygiene in food storage environments.

Moreover, user-friendly designs are a priority, with thoughtfully arranged interior shelving options that cater to various product sizes and shapes. The user experience is enhanced with features such as LED lighting, which provides excellent visibility while being energy-efficient.

In conclusion, Bally Refrigerated Boxes' refrigerators, freezers, and warmers are built to deliver on performance, efficiency, and durability. With a wide range of options tailored to commercial needs, their innovative technology and design characteristics make them a reliable choice for any food service operation. Professionals in the industry can trust Bally to not only meet but exceed their refrigeration and warming requirements, ensuring that food safety and quality remain paramount.
Top Page Image Contents