Liebherr 7083 247-00 operating instructions Safety instructions and warnings, Setting up

Page 3

Safety instructions and warnings

To prevent injury or damage to the unit, the ap- pliance should be unpacked and set up by two people.

In the event that the appliance is damaged on delivery, contact the supplier immediately before connecting to the mains.

To guarantee safe operation, ensure that the ap- pliance is set up and connected as described in these operating instructions.

Disconnect the appliance from the mains if any fault occurs.Pull out the plug, switch off or remove the fuse.

When disconnecting the appliance, pull on the plug, not on the cable.

Any repairs and work on the appliance should only be carried out by the customer service department, as unauthorised work could prove highly dangerous for the user. The same applies to changing the mains power cable.

Do not allow naked flames or ignition sources to enter the appliance.When transporting and clean- ingtheappliance,ensurethattherefrigerantcircuit is not damaged. In the event of damage, make sure that there are no ignition sources nearby and keep the room well ventilated.

Do not stand on the plinth, drawers or doors or use them to support anything else.

This appliance is not intended for use by persons

(including children) with reduced physical, sen- sory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Avoid prolonged skin contact with cold surfaces or chilled/frozen food.This could cause pain, numb- ness and frostbite. In the case of prolonged skin contact, protective measures should be taken, e.g. gloves should be worn.

Do not consume food which has been stored for too long, as it could cause food poisoning.

Do not store explosives or sprays using combusti- blepropellantssuchasbutane,propane,pentane, etc.in the appliance.Electrical components might cause leaking gas to ignite.You may identify such sprays by the printed contents or a flame symbol.

GB

Do not use electrical appliances inside the appli- ance.

If you have a lockable appliance, do not keep the key near the appliance or within reach of children.

The appliance is designed for use in enclosed areas. Do not operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions.

The fluorescent tube illuminates the interior of the appliance. It is not suitable for lighting a room.

Do not install the appliance in the immediate vicinity of an air-conditioning unit. The appliance should also not be operated under a wall-mounted air-conditioning unit.

The appliance is not suitable for storing drugs pursuant to DIN 58345.

The appliance is not suitable for storing blood bottles pursuant to DIN 58371.

In special fields of application which are subject to their own standard, the user is responsible for complying with this standard.

Setting up

Avoid positioning the appliance in direct sunlight or near cookers, radiators and similar sources of heat.

The floor on which the appliance stands should be horizontal and level. Compensate for uneven floors with the adjustable feet.

Do not cover ventilation open-

ings or grille.

• Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m3 per 8 g of R 600a refrigerant used in the appliance, so as to avoid the formation of inflammable gas/air mixtures in the room where the appliance is located in the event of a leak in the re- frigerant circuit.The quantity of refrigerant used in your appliance is indicated on the type plate on the inside of the appliance.

15

Image 3
Contents LKUv 7083Description of the appliance Appliance dimensionsDisposal notes Range of appliance useSetting up Safety instructions and warningsDoor open alarm Switching the appliance on and offSetting the temperature Audible warning signalDisplay = Setting the delay time for the door open alarmDeactivating the audible warning signal function Audible warning signal settingsAlarm messages Alarm testAdjusting the alarm parameters Resetting the recorded temperature progres- sion Example of an alarm querySituation Haccp flashes in the display Display = Calibrating the control sensor standard sensor for Calibrating the product sensorActivating the sensor Resetting the parameters to factory settings Setting the real time clockChanging the network address Defrosting Safety lockSetting the display indication for the defrost phase CoolingMalfunctions CleaningDo not use steam cleaners because Risk of injury and damage Opening for external temperature sensorRx- / Tx External alarmFloating alarm output RS485 interfaceUnscrew the hinge bracket Installation dimensions mmChanging over door hinges Version