Liebherr BF/BFI 1051, BGEN/es 2956 Electrical Safety, IceMaker if equipped, Safety Instructions

Page 7

SAFETY

•Do not use electrical appliances inside the appliance.

•Do not allow children to play with the appliance. Children must not climb, sit or stand on the shelves, drawers or door.

•To prevent possible injury due to an electrical shock, be sure to disconnect the power cord or turn off the circuit breaker before replacing the interior light or cleaning the appliance.

•To prevent possible injury due to broken glass, use hand protection when replacing the interior light.

•To avoid injury or damage to the appliance, do not use steam cleaning equipment to clean the appliance.

•Do not operate the refrigerator in the presence of explosive fumes.

•In the event of a power outage, minimize opening the refrigerator door(s). Protect the food either by placing dry ice on top of the packages or using a local frozen food locker if the power failure is of a long duration. Do not attempt to re-freeze any thawed previously frozen food.

•To avoid possible injury, only adjust an empty shelf. Do not attempt to adjust a shelf with food on it.

•To protect the refrigerator from possible damage, allow the appliance to stand 1/2 to 1 hour in place before turning the electricity on. This allows the refrigerant and system lubrication to reach equilibrium.

Electrical Safety

Connect this appliance to a 110-120 VAC, 15 amp (20 Amp for side-by-side installations) circuit that is controlled by a circuit breaker or fuse. This appliance should have its own separate grounded circuit. Do not use an extension cord.

The power cord is equipped with a three-prong (grounding) plug for your protection against possible shock hazards. To maintain this protection:

•Do not modify the plug by removing the round grounding prong.

•Do not use a two-prong adapter. Where a two- prong wall receptacle is encountered, contact a qualified electrician and have it replaced with a three-prong receptacle in accordance with all local codes and ordinances.

•Do not use a power cord that is frayed or damaged.

IceMaker (if equipped)

The icemaker for a combined refrigerator-freezer is located in the freezer compartment. It must be connected to the water supply to function properly. These instructions only refer to the installation and operation of the icemaker. Please refer to the Use and Care Manual provided with the appliance for other installation and operation instructions. The combined refrigerator-freezer must be level for the icemaker to function properly.

Safety Instructions and

Warnings

•Do not make the water connection while the combined refrigerator-freezer is connected to an electrical outlet.

•The connection to the water supply may only be made by a trained and licensed plumber.

•The water quality must comply with the drinking water regulations for the geographical area where the appliance is located.

•The icemaker is designed exclusively to make ice cubes in quantities needed by a household and may only be operated with water appropriate for this purpose.

•All repairs and work on the icemaker may only be done by customer service personnel or other trained personnel.

•Do not consume or use the first three batches of ice. This applies both to using the appliance for the first time and also using it after it has not been used for a long period of time.

•The manufacturer cannot accept liability for damage caused by equipment or water lines between the solenoid valve and the water supply.

BF/BFI 1051

3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Use Care Manual Additional benefits Table of Contents BF/BFI Operating and Control Elements Figure FeaturesImportant Safety Information SafetyDisposal of Old Appliance Safety Instructions Electrical SafetyIceMaker if equipped Unpacking Safety RegulationsDisposal of Carton Operation Setting the Temperature FigureTo reduce the temperature To increase the temperatureDisplay will flash Additional FeaturesTemperature Display Figure Audible Warning Signal FigureSuperFrost Figure Audible Door Alarm For BioFreshAudible/Visual Temperature Power Failure/Frost-ControlStorage Times Biofresh CompartmentBioFresh Compartment Humidity Selection FigureFruit Humid setting Vegetables, saladArranging Food Figure Shelf Arrangement Bulb data To install the drawersInterior Light Figure To remove the drawersInformation System Figure Freezer CompartmentFreezing, Storage Figure Freezing with SuperFrost FigureDo Not Freeze Removing and Installing the ShelvesFreezing and Storage Removing DrawersIcemaker To Clean the IceMaker FigureTo Start the IceMaker Figure To clean the BioFresh drawers DEFROSTING/CLEANINGCleaning Figure To clean the storage shelvesShort vacations Vacation TipsLong vacations Failure/Frost-Control Display TroubleshootingProblem Possible Cause and Remedy Normal SoundsCustomer Service Figure WarrantyAppliance Information Liebherr Warranty Plan

BF/BFI 1051, BGEN/es 2956 specifications

The Liebherr BGEN/es 2956 and BF/BFI 1051 are two innovative products from the renowned Liebherr Group, known for its cutting-edge technology and exceptional engineering in the construction and building industries. Both units exemplify Liebherr's commitment to quality, efficiency, and user-friendly operation.

The Liebherr BGEN/es 2956 is a powerful and versatile tower crane that has gained popularity in the construction sector. It boasts a maximum lifting capacity of 25 tons and a maximum hook height of over 60 meters, making it suitable for large-scale construction projects. One of its standout features is its innovative counter-jib design, which drastically reduces the crane's footprint, allowing for efficient use of space on crowded job sites. Additionally, the BGEN/es 2956 is equipped with advanced control technology, enabling precise and smooth operation. The crane's transportability is also a key characteristic, allowing for easy assembly and disassembly without compromising structural integrity.

On the other hand, the Liebherr BF/BFI 1051 series represents a modern take on concrete batching technology. These powerful concrete mixing plants are designed for high output and efficiency, providing a consistent quality of concrete at various production scales. The BF/BFI 1051 plants incorporate state-of-the-art automation systems, making it possible to monitor and control the mixing process remotely. This feature enhances operational efficiency and minimizes downtime. The system’s modular design also allows for easy customization, enabling users to adapt the equipment to different production requirements.

Both the BGEN/es 2956 and BF/BFI 1051 exemplify Liebherr's dedication to sustainability. The crane integrates energy-saving technologies, significantly reducing its overall carbon footprint. Meanwhile, the concrete plants are designed to optimize resource usage, ensuring minimal waste during operation.

In conclusion, the Liebherr BGEN/es 2956 and BF/BFI 1051 offer impressive features and technologies that meet the demands of modern construction and concrete production. With their robust engineering, advanced automation, and focus on sustainability, they are valuable assets for any construction project. Liebherr continues to set standards in the industry, providing innovative solutions that enhance productivity and efficiency in various applications.
Top Page Image Contents