Liebherr BF/BFI 1051, BGEN/es 2956 Audible Door Alarm For BioFresh, Audible/Visual Temperature

Page 11

OPERATION

Audible Door Alarm - For BioFresh

and Freezer Compartment

The audible door alarm will sound when the doors have been left open for longer than 60 seconds.

The alarm will sound as long as the door is left open or the ON/OFF button is not pressed.

The alarm will automatically reset when the door is closed.

Audible/Visual Temperature

Alarm - For Freezer Compartment

The alarm always sounds if the freezer temperature is not low enough based on the temperature setting. The temperature display will also flash at the same time.

This can be caused by:

•warm, fresh food being placed in the freezer.

•too much warm air from the outside is entering when re-arranging or removing frozen food.

The temperature display will continue to flash until the cause has been rectified. It will then stop flashing and temperature will display. The audible warning signal will also reset.

Power Failure/Frost-Control

Display - Figure 1

If appears in the display, this means the freezer temperature has risen too high

during the last few hours or days due to a power failure.

•If you press the Alarm button (Fig. 1, 5) while the display is reading, the highest temperature registered during the power failure will be displayed.

•Check the quality of the food in case it has become too warm or even defrosted.

•The highest temperature will appear for approximately one minute. After that, the actual temperature in the freezer will reappear. The display can be turned OFF by repeatedly pressing the Alarm button.

Once the power is re-instated, the appliance will continue to operate at the most recent temperature setting

SuperFrost - Figure 1

Fresh food should be frozen to the core as rapidly as possible. Frozen food can also be given a cold boost. This is provided by the SuperFrost feature (Fig. 1, 4) and ensures the nutritional value, appearance and flavor of the food remains intact.

•For more information, refer to Freezing with

SuperFrost.

BioCool - Figure 1

The BioCool button switches the BioFresh compartment to maximum cooling. It is recommended to cool large quantities of food, freshly baked cakes or meals rapidly.

•To turn ON: Press the BioCool button (Fig. 1, 10) briefly. When the symbol is lit, BioCool is activated.

Note

The BioCool function uses slightly more energy. After approximately six hours, the electronic control system will automatically switch back to normal energy-saving operation.

The BioCool function can be turned OFF sooner.

•To turn OFF: Press the BioCool button, if the indicator is lit and BioFresh will turn OFF.

BF/BFI 1051

7

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Use Care Manual Additional benefits Table of Contents BF/BFI Operating and Control Elements Figure FeaturesDisposal of Old Appliance SafetyImportant Safety Information IceMaker if equipped Electrical SafetySafety Instructions Disposal of Carton Safety RegulationsUnpacking Operation Setting the Temperature FigureTo reduce the temperature To increase the temperatureDisplay will flash Additional FeaturesTemperature Display Figure Audible Warning Signal FigureSuperFrost Figure Audible Door Alarm For BioFreshAudible/Visual Temperature Power Failure/Frost-ControlStorage Times Biofresh CompartmentBioFresh Compartment Humidity Selection FigureFruit Humid setting Vegetables, saladArranging Food Figure Shelf Arrangement Bulb data To install the drawersInterior Light Figure To remove the drawersInformation System Figure Freezer CompartmentFreezing, Storage Figure Freezing with SuperFrost FigureDo Not Freeze Removing and Installing the ShelvesFreezing and Storage Removing DrawersTo Start the IceMaker Figure To Clean the IceMaker FigureIcemaker To clean the BioFresh drawers DEFROSTING/CLEANINGCleaning Figure To clean the storage shelvesLong vacations Vacation TipsShort vacations Failure/Frost-Control Display TroubleshootingProblem Possible Cause and Remedy Normal SoundsAppliance Information WarrantyCustomer Service Figure Liebherr Warranty Plan

BF/BFI 1051, BGEN/es 2956 specifications

The Liebherr BGEN/es 2956 and BF/BFI 1051 are two innovative products from the renowned Liebherr Group, known for its cutting-edge technology and exceptional engineering in the construction and building industries. Both units exemplify Liebherr's commitment to quality, efficiency, and user-friendly operation.

The Liebherr BGEN/es 2956 is a powerful and versatile tower crane that has gained popularity in the construction sector. It boasts a maximum lifting capacity of 25 tons and a maximum hook height of over 60 meters, making it suitable for large-scale construction projects. One of its standout features is its innovative counter-jib design, which drastically reduces the crane's footprint, allowing for efficient use of space on crowded job sites. Additionally, the BGEN/es 2956 is equipped with advanced control technology, enabling precise and smooth operation. The crane's transportability is also a key characteristic, allowing for easy assembly and disassembly without compromising structural integrity.

On the other hand, the Liebherr BF/BFI 1051 series represents a modern take on concrete batching technology. These powerful concrete mixing plants are designed for high output and efficiency, providing a consistent quality of concrete at various production scales. The BF/BFI 1051 plants incorporate state-of-the-art automation systems, making it possible to monitor and control the mixing process remotely. This feature enhances operational efficiency and minimizes downtime. The system’s modular design also allows for easy customization, enabling users to adapt the equipment to different production requirements.

Both the BGEN/es 2956 and BF/BFI 1051 exemplify Liebherr's dedication to sustainability. The crane integrates energy-saving technologies, significantly reducing its overall carbon footprint. Meanwhile, the concrete plants are designed to optimize resource usage, ensuring minimal waste during operation.

In conclusion, the Liebherr BGEN/es 2956 and BF/BFI 1051 offer impressive features and technologies that meet the demands of modern construction and concrete production. With their robust engineering, advanced automation, and focus on sustainability, they are valuable assets for any construction project. Liebherr continues to set standards in the industry, providing innovative solutions that enhance productivity and efficiency in various applications.
Top Page Image Contents