Liebherr BGEN/es 2956 Icemaker, To Start the IceMaker Figure, To Clean the IceMaker Figure

Page 18

ICEMAKER

To Start the IceMaker - Figure 10

The IceMaker will only work if the combined refrigerator-freezer is connected to the electrical outlet. It will only make ice cubes if the freezer compartment is operating.

The IceMaker is in the top left drawer in the freezer compartment of the combined refrigerator- freezer. You can identify this drawer by its labeling “IceMaker.”

To turn on

•Pull out the drawer.

•Press the “ON/OFF” button so the control lamp comes on (Figure 10).

•Close the drawer.

Note

The icemaker can only make ice cubes if the drawer is completely closed.

Figure 10

To turn off

If you do not need any ice cubes, the icemaker can be turned off independently of the freezer compartment.

•Press the “ON/OFF” button for approximately 1 second so the control lamp goes out.

Note

If the icemaker is turned off, the empty drawer can also be used to freeze and store food.

The production capacity depends on the temperature inside the freezer compartment. The lower the temperature, the more ice can be produced over a period of time.

The ice cubes fall out of the icemaker into the drawer. When the ice reaches a certain level in the drawer, the appliance stops producing ice automatically.

If you need a large quantity of ice you can change out the drawer to the right with the complete “IceMaker” drawer. When you close the drawer the icemaker will immediately start production.

To Clean the IceMaker - Figure 11

The IceMaker (arrow in Figure 11) can be cleaned by using this procedure.

1.Pull out the drawer and remove the ice.

2.Clean the drawer with warm water and mild dish detergent.

3.To access the IceMaker for cleaning:

a.With the drawer pulled out, press and hold the “ON/OFF” button until the LED goes out (takes about 1 second).

b.Continue to hold the button and after 10 seconds the LED will start to flash.

c.Insert the drawer while the LED is flashing. The IceMaker should rotate down into the cleaning position.

d.Remove the drawer.

4.Clean the IceMaker with warm water. If you need to use a cleaning aid, use a mild dish detergent and rinse. You will need to throw out the first three batches of ice if you use any soap.

5.Push the “ON/OFF” button until the LED lights and insert the drawer.

6.Throw out the first three batches of ice to remove any soap residue.

Note

If you need to leave the IceMaker off, clean the IceMaker but do not push the “ON/OFF” button in Step 5.

To make ice cubes

After you start the icemaker for the first time it may take up to 24 hours before the first ice cubes are ready.

Note

The first three batches of ice must not be consumed or used.

Figure 11

* Depending on model and options

14

BF/BFI 1051

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Use Care Manual Additional benefits Table of Contents BF/BFI Features Operating and Control Elements FigureSafety Important Safety InformationDisposal of Old Appliance Electrical Safety Safety InstructionsIceMaker if equipped Safety Regulations UnpackingDisposal of Carton To increase the temperature Setting the Temperature FigureTo reduce the temperature OperationAudible Warning Signal Figure Additional FeaturesTemperature Display Figure Display will flashPower Failure/Frost-Control Audible Door Alarm For BioFreshAudible/Visual Temperature SuperFrost FigureHumidity Selection Figure Biofresh CompartmentBioFresh Compartment Storage TimesHumid setting Vegetables, salad FruitArranging Food Figure Shelf Arrangement To remove the drawers To install the drawersInterior Light Figure Bulb dataFreezing with SuperFrost Figure Freezer CompartmentFreezing, Storage Figure Information System FigureRemoving Drawers Removing and Installing the ShelvesFreezing and Storage Do Not FreezeTo Clean the IceMaker Figure IcemakerTo Start the IceMaker Figure To clean the storage shelves DEFROSTING/CLEANINGCleaning Figure To clean the BioFresh drawersVacation Tips Short vacationsLong vacations Normal Sounds TroubleshootingProblem Possible Cause and Remedy Failure/Frost-Control DisplayWarranty Customer Service FigureAppliance Information Liebherr Warranty Plan

BF/BFI 1051, BGEN/es 2956 specifications

The Liebherr BGEN/es 2956 and BF/BFI 1051 are two innovative products from the renowned Liebherr Group, known for its cutting-edge technology and exceptional engineering in the construction and building industries. Both units exemplify Liebherr's commitment to quality, efficiency, and user-friendly operation.

The Liebherr BGEN/es 2956 is a powerful and versatile tower crane that has gained popularity in the construction sector. It boasts a maximum lifting capacity of 25 tons and a maximum hook height of over 60 meters, making it suitable for large-scale construction projects. One of its standout features is its innovative counter-jib design, which drastically reduces the crane's footprint, allowing for efficient use of space on crowded job sites. Additionally, the BGEN/es 2956 is equipped with advanced control technology, enabling precise and smooth operation. The crane's transportability is also a key characteristic, allowing for easy assembly and disassembly without compromising structural integrity.

On the other hand, the Liebherr BF/BFI 1051 series represents a modern take on concrete batching technology. These powerful concrete mixing plants are designed for high output and efficiency, providing a consistent quality of concrete at various production scales. The BF/BFI 1051 plants incorporate state-of-the-art automation systems, making it possible to monitor and control the mixing process remotely. This feature enhances operational efficiency and minimizes downtime. The system’s modular design also allows for easy customization, enabling users to adapt the equipment to different production requirements.

Both the BGEN/es 2956 and BF/BFI 1051 exemplify Liebherr's dedication to sustainability. The crane integrates energy-saving technologies, significantly reducing its overall carbon footprint. Meanwhile, the concrete plants are designed to optimize resource usage, ensuring minimal waste during operation.

In conclusion, the Liebherr BGEN/es 2956 and BF/BFI 1051 offer impressive features and technologies that meet the demands of modern construction and concrete production. With their robust engineering, advanced automation, and focus on sustainability, they are valuable assets for any construction project. Liebherr continues to set standards in the industry, providing innovative solutions that enhance productivity and efficiency in various applications.
Top Page Image Contents