hussman IGSS-ESS, ESSS-0303 manual Corner Wedges, ESS Refrigerated, Dry, Joint Trim

Page 5

Rev.0303

Installation (cont.)

Do not use cam locks to pull cases together.

2.Secure joint backer. Located behind cart bumper suport at joints.To adjust screws holding bumper cart to case on either side or the joint and slide extrusion to center of joint.This piece supports the fornt panel at the joint.

3.Apply bead of silicone to top of bulkheads.

4.Slip on stainless steel bulkhead cap. Also apply silicone to seam between overhead light tubes.

5.Recheck all camlocks.

CORNER WEDGES

If a wedge is used in the middle of the lineup, the wedge must be set off the highese point on the floor FIRST, with the rest of the lineup being leveled from that point.

If an outside corner display is used, it must be mounted and set before attaching any joint trim parts. Set the front stainless steel bumper so it aligns with bumpers on the two cases.

ESSS

Touches” section of this booklet). Fasten along the top edge, or center, with #10 x 3/4” sheet metal screws in the pre-drilled holes.

ESS

REFRIGERATED

Inside Wedge: Line up taper pins with holes on adjoining case.Turn camlock to lock in.Two camlocks are located at the rear of the case behind the air discharge and behind the lower electrical raceway panel. Bolt the front of the wedge into the adjoining case. In refrigerated cases, the bolt is located under the pans in the front. In the hot case, the cases are bolted together by means of a bracket lo- cated behind the front panel. Remove the front panel by lifting up and then sliding out.

Outside wedge:Taper pin and camlock locations are the same as a standard case.

DRY

Inside Wedge: Bolt the wedge into the sides of the adjoin- ing case. Use bolts provided.

Inside Pedestal Wedge: Set wedge on the adjoining case’s mounting brackets located at the base of the unit, and bolt down. Drive screws provided through the sides of the wedge (4 screws per side),accessible through the back of the wedge.

COMMON END BETWEEN UNLIKE CASES AND HOT CASES

Bolt end onto case using bolts provided in pre-drilled holes behind front panel through brakcet provided and in the rear behind the rear access panel on the bottom. Hot cases are onlu bolted in two places. Common ends be- tween refrigerated cases are bolted together the air dis- charge panel. Remove air discharge panel by lifting up and out.

Nex connect applicable electrical, refrigeration, water, and drain lines.

JOINT TRIM

After cases have been leveled and joined, and refrigera- tion, electrical, and wasted piping work completed, install the splashguards. Fasten along the top edge, or center, with #10 X 3/3" sheet metal screws.

Anchor woth bolts through bracket hjoles on legs of cases.

Install rear stianless steel plate with shelf standards to backDO NOT SEAL JOINT TRIM TO FLOOR! edge of ends with screws. Install brackest and shelves.

Next,connect applicable electrical,refrigeration,water,and drain lines throug the access panels in the side of the stand. After the cases have been leveled and joined, and refrig- eration, electrical, and waste paping work completed, in- stall the splashguards. (See instructions in the “Finishing

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Esss / ESS Shipping Damage This Booklet Contains Information onApparent Loss or Damage Concealed Loss or DamageEsss Cut & Plan ViewsLeveling and Placement Setting and JoiningUncrating the Stand Exterior LoadingESS Refrigerated Corner WedgesDRY Common END Between Unlike Cases and HOT CasesWaste Outlet and P-TRAP Installing Condensate DrainPlumbing Access to TX Valves & Drain Lines Control SettingsExpansion Valve Adjustment Refrigerant TypeField Wiring & Serial Plate Amperage Wiring Color CodeElectrical Electrical Circuit IdentificationEsss Only Joint TrimUser Information StockingCleaning Glass & Mirrors Case CleaningCleaning Precautions When Cleaning Plexiglass & Acrylic Care CleaningAntistatic Coatings Parts ListPlexiglass Repair InstructionsTips & Troubleshooting ReplacementFor Prompt Service Replacing Fluorescent LampsModel Specifications2CaselayoutwithT8Lights Electrical Schematics0100-04-125 PigtailcaseSingle 0101-04-125 Solenoid Gfci ASC 12CasewithT8Lights Type of Refrigerator Typical Entering Air Temperature Appendix A. Temperature GuidlinesAppendices Appendix B. Application RecommendationsAppendix D. Recommendations to user Are the refrigerant controls incorrectly adjusted?IGSS-ESS/ESSS-0303 Limited Warranty Model Serial Number

IGSS-ESS, ESSS-0303 specifications

The Hussman ESSS-0303 and IGSS-ESS are revolutionary products in the world of commercial refrigeration, known for their ability to deliver energy-efficient performance while ensuring optimal food preservation. These systems feature cutting-edge technology that caters to the needs of supermarkets, convenience stores, and other retail environments where refrigeration is crucial.

One of the primary features of the Hussman ESSS-0303 is its advanced energy management capabilities. The system is equipped with intelligent controls that analyze energy consumption patterns, optimizing performance in real time. This not only helps to reduce operational costs but also contributes to sustainability efforts by minimizing energy waste.

Another significant aspect of the ESSS-0303 is its ability to maintain precise temperature control. This is achieved through a combination of high-quality insulation and advanced refrigeration technology, which ensures that products remain fresh for longer periods. The unit offers temperature ranges specifically designed for various applications, whether it be for dairy products, frozen foods, or fresh produce.

The Hussman IGSS-ESS, on the other hand, is designed to integrate seamlessly with existing refrigeration setups, allowing for a smooth transition to newer technologies. Its modular design allows businesses to easily expand their refrigeration capabilities without the need for extensive renovations. In addition, the IGSS-ESS features remote monitoring capabilities, which enables store managers to track performance and diagnose potential issues from a distance, ensuring minimal downtime.

These systems are also built with user-friendliness in mind. The intuitive control interface allows for easy programming and adjustments, empowering staff to efficiently manage the refrigeration environment. Furthermore, Hussman has made durability a priority; both the ESSS-0303 and IGSS-ESS are constructed from robust materials, ensuring longevity even in high-demand retail settings.

In summary, the Hussman ESSS-0303 and IGSS-ESS offer enhanced energy efficiency, precise temperature control, integration capabilities, remote monitoring, and user-friendly interfaces. These characteristics make them ideal choices for retailers seeking to optimize their refrigeration solutions while maintaining product quality and reducing energy costs. As businesses continue to prioritize sustainability and efficiency, the Hussman range stands out as a reliable partner in commercial refrigeration technology.
Top Page Image Contents