Mitsubishi Electronics A0567659 specifications Machine Mount

Page 29

Machine Mount

In a machine mounting application of the Slide Gate/Auger unit, there are a few items to review before placement and mounting of the blending system begins.

First, verify the machine flange dimensions match the Slide Gate blender flange (if the optional pre-drilled holes were ordered). The Slide Gate blender can also be equipped with an optional cast throat section with a drain port. This will bolt under the bottom plate of the blender.

Verify that the machine throat is physically capable of supporting the Slide Gate/Auger blending system with a full load of material and vacuum loading equipment installed.

Note: While in operation, the Slide Gate/Auger blender applies horizontal and vertical pressures to the mounting flange. If there is a question as to the mechanical stability of a mounting flange, contact the manufacturer’s engineering department.

Verify all clearances on the top and beside the processing machine. This is to insure that all motors, hoppers, control panels, etc. have adequate room for proper operation and servicing.

Refer to the assembly drawing with the unit for actual height and width dimensions.

Note: Allow at least 36” clearance around blender to provide adequate room for cleaning, servicing, etc.

Using proper lifting equipment, lift the blender, using the lifting lugs attached to the top plate of the blender. These lifting lugs can also be used to fasten horizontal or angled braces to the blender if more stability is needed.

Take care to insure proper orientation with adequate access to operator controls, mix chamber, and metering units.

Note: Never weld on the blender, support stand, machine or mezzanine without first removing the control panel and verifying that the blender is properly grounded.

Gravimetric Batch Blenders w/Mitsubishi Control Chapter 3: Installation

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Write Down Your Serial Numbers Here For Future Reference Shipping Information Credit Returns Warranty ReturnsTable of Contents Troubleshooting Addendum Safety Symbols Used in this Manual SafetyHow to Use This Manual Gravimetric Batch Blender Safety Tags Description Wear Safety Glasses and Work Gloves Follow all Safety CodesGeneral Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityCustomer Service AccessoriesFunctional Description Models Covered in This ManualBoth Blender Styles Typical Features & ComponentsMechanical Features Blender Controller shown with Mitsubishi Touch Screen Controller FeaturesMaterial Supply Hoppers Slide Gate & Auger Blender System Component DescriptionSlide Gate Metering Assemblies Slide Gate Blenders Auger Blenders available with a Choice of Mixers Auger Metering AssembliesTypical Weigh Hopper Weigh HopperMix Chamber Weigh Hopper Discharge ValveOpti-Mixer HC MixerController Pushbutton & Touchscreen Tags Button Function Operator Control PanelTypical Setup Screens Logo Pneumatic Slide Gate Below Mixer OptionsRemote Touch Screen Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-OutsTwist Cap Plug Electric Safety Interlock Switch All ModelsMounting Configuration InstallationUncrating the Equipment Rigging and Placing the UnitMachine Mount Mezzanine Mounted Batch Blender Mezzanine MountTypical Central Blender Layout Floor Mount Central BlenderMechanical Installation Electrical InstallationCustomer-Supplied Components Pneumatic InstallationStroke Limiters for Metering Gates Weigh Hopper Installation Slide Gate Models onlySet-up Load Cell Mechanical Stop Adjustment Load Cell AdjustmentLogo Final ConnectionsRecipe Format Menu Controller SetupRecipe Entry Formats Quickset Mode Most common in injection molding Percentage Mode Most common in extrusion and blow molding Switching Modes Parts Mode Often used in Compounding ApplicationsCurrent Recipe Menu Feeder Metering OrderInventory Shutdown Batch Size MenuWeigh Every Batch Batch Ready ModeAutoStart Feature Every Fourth Batch Every Second BatchEvery Third Batch Printer Features Print Inventory Batch Interval or Timed Interval PrintoutDisplay Time and Date Blender CalibrationPage Why Blender Calibration is Necessary Feeder Calibration Auger Blenders Re-Mix Timer Mix TimerWeigh Hopper Dump Cycle Weigh Hopper Dump Delay TimeWeigh Hopper Dump Time Feeder Alarm Setup & Flags Setting Date & TimeMixer Options Timed Mixing OptionMAX Hopper Weight Exceeded Power Interruption Additional settings that usually do not have to be changed Network Communications Baud Rate & I.D. SettingsShutting Down Blender Initial StartupOperation Quick Start ProcedureStart-up General OperationExisting Recipes Display Description LCD Controller Description & OperationRecipe Page Start Slide Gate & Auger Blender Control System Menu StructureRecipe Book Storage Menus Control FunctionsSave Running Recipe to the Book Display Recipe ContentsLoad a Saved Recipe from the Book Erase Recipe or Entire BookFeeder Clean Out Color Changes Page Standard Run Time Displays Shutting Down the Blender Photocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Corrective Maintenance Preventative MaintenanceElectrical Internal Components of the Control PanelOutput Signals from Programmable Controller Input Signals to Programmable ControllerPneumatic System Maintenance Introduction TroubleshootingProblem Corrective action ±10%. This voltage must remain constant with all the motors Problem Corrective action Warranty will be voided Problem Corrective action Warranty Specifications WarrantyWarranty Restrictions Warranty LiabilitiesAnnex B Information Technical SpecificationsCustomer Responsibilities Auger Blender -E Series Specifications Slide Gate Blender -E Series SpecificationsSpare Parts List Drawings & DiagramsTypical Slide Gate Model Assembly Overview Slide Gate Gravimetric Batch Blending SystemsModel 002 with Opti-Mixer Model 4000Auger Gravimetric Batch Blending Systems Model 012 with Common Feeder Components Model 012 with Opti-MixerModel 012 with Rotary HC mixer Model 060 with Rotary HC Mixer Model 060 with OptimixerModel 060 with Common Feeder Components Typical Mixer Section Front Typical Opti-Mixer Front Assembly DetailTypical Mixer Section Rear Typical Opti-Mixer Rear Assembly DetailTypical Mixer Frame Typical Opti-Mixer Frame AssemblyTypical Slide Gate Diamond Gate Assembly Detail Typical Gate AssemblyTypical Supply Hopper Typical Slide Gate-014 Series Hopper Assembly DetailTypical Weigh Hopper & Load Cell Detail Technical Assistance Blender Identification Serial Number TagProgrammable Settings Service Supervisor InformationFactory Setup Menu Available Selections AddendumFeed Algorithm Options Screen Advanced Weight Options ScreenMechanical Options Screen Feed Calibration Options ScreenCustomer Setup Menu Feeder SetupNetwork Setup UnitsAlarm Log Alarm SetupPasswords Programmable FeaturesUser Password Maintenance Password

A0567659 specifications

Mitsubishi Electronics A0567659 is an advanced display module that embodies the cutting-edge technology and innovation that Mitsubishi is renowned for. Designed primarily for industrial applications, this display module stands out due to its robust performance and exceptional image quality, making it an ideal choice for various sectors including automation, transportation, and manufacturing.

One of the main features of the A0567659 is its high-resolution display capability. With a resolution that provides clear and detailed visuals, users can expect enhanced readability and precision in their data visualization tasks. This is particularly important in industrial environments where the accuracy of information can significantly impact operational efficiency.

The display utilizes advanced LCD technology, ensuring vibrant colors and high contrast ratios that make the content easily viewable under different lighting conditions. The screen's brightness is adjustable, allowing users to customize their visual experience according to the specific needs of their workplace. The durability of the A0567659 is another highlight, as it is built to withstand harsh conditions including extreme temperatures and exposure to dust and moisture. This ruggedness is essential for maintaining long-term performance in demanding environments.

In terms of connectivity, the A0567659 is equipped with multiple interfaces, making it versatile for integration with various systems. Whether it’s connecting to a PLC, computer, or other control devices, users can benefit from seamless communication across their technological ecosystem. This feature underlines Mitsubishi's focus on facilitating smooth integration within existing infrastructures.

Another significant characteristic is its energy efficiency. The A0567659 is designed to consume less power while delivering high performance, aligning with the growing trend of sustainable technology solutions. This aspect not only helps in reducing operational costs but also makes it an environmentally friendly choice for businesses looking to minimize their carbon footprint.

Furthermore, Mitsubishi Electronics places a strong emphasis on user-friendliness. The display module is designed with an intuitive interface that simplifies the operation for users at all skill levels. This ease of use, combined with thorough documentation and support, ensures that users can harness the full potential of the A0567659 without extensive training or technical expertise.

In conclusion, the Mitsubishi Electronics A0567659 is a powerful display module characterized by its high-resolution display, durability, versatile connectivity, and energy efficiency. It represents a robust solution for industries that demand reliable and high-quality visual communication tools.
Top Page Image Contents