Mitsubishi Electronics A0567659 specifications Color Changes

Page 63

The open weigh hopper dump door will allow the material to drop into the mixer section of the blender. If the dump delay is set, the mixer will start before the weigh hopper dump will open for the selected time.

The blender will sit at rest until the high-level sensor in the mixing chamber is uncovered to start another weigh cycle. (Unless the Re-Mix timer is set to a value other than 0 and times out to restart the mixer to run for another mix cycle.)

The level sensor is located on the back wall of the mixer chamber. If the sensor is covered with material, the indicator light on the back of the sensor will be lit.

Once this sensor is uncovered, the indicator lamp on the back of the level sensor will go out. This level sensor must be uncovered for approximately 1 - 2 seconds to indicate to the controller that there is room in the mixing section to accept a batch of material.

When the controller has determined that the mixer is ready for an additional batch of material, the controller will begin metering material into the weigh hopper assembly.

Color Changes

The color change procedure is meant for use with the basic Slide Gate/Auger Blender. This procedure assumes that the color component of the blend is in an additive ingredient hopper (#2, #4, #5, or #6).

Note: The blender must be stopped to make color changes. The processing machine can operate on virgin material only during this procedure with an optional quick color change bypass tube that can be installed to bypass the blender. Contact the factory for details.

1.Disable and clean any color loading equipment. Please refer to the loading equipment manual for any clean up recommendations.

2.Using the blender “Abort” or “Push to Start or Stop” key, put the blender in stop mode. After the cycle has completed, switch “OFF” the main power switch and unplug the blender power supply.

3.Open the upper mixer access door. This shuts off air to the blender circuit by deactivating the master air valve. Then unplug the quick disconnect from the air supply hose to the blender to further ensure that no air pressure is supplied to the blender.

WARNING! Always unplug the main power cord.

WARNING! Always disconnect the air supply to the blender.

WARNING! ...prior to performing any operations inside any access areas of the blender where there are moving parts.

4.Remove the weigh hopper by unplugging the air line disconnect fitting, holding the dump valve closed, lifting the hopper to clear the load cell brackets, and gently pulling the weigh hopper out of the blender.

Note: To reduce the chance for damage to delicate load cells, use care when lifting the weigh hopper off load cell locating tabs and when reinstalling the weigh hopper on load cell brackets.

Gravimetric Batch Blenders w/Mitsubishi Control Chapter 4: Operation

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Write Down Your Serial Numbers Here For Future Reference Shipping Information Credit Returns Warranty ReturnsTable of Contents Troubleshooting Addendum Safety How to Use This ManualSafety Symbols Used in this Manual Gravimetric Batch Blender Safety Tags Description Wear Safety Glasses and Work Gloves Follow all Safety CodesGeneral Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityModels Covered in This Manual AccessoriesCustomer Service Functional DescriptionTypical Features & Components Mechanical FeaturesBoth Blender Styles Blender Controller shown with Mitsubishi Touch Screen Controller FeaturesMaterial Supply Hoppers Slide Gate & Auger Blender System Component DescriptionSlide Gate Metering Assemblies Slide Gate Blenders Auger Blenders available with a Choice of Mixers Auger Metering AssembliesTypical Weigh Hopper Weigh HopperHC Mixer Weigh Hopper Discharge ValveMix Chamber Opti-MixerController Pushbutton & Touchscreen Tags Button Function Operator Control PanelTypical Setup Screens Logo Options Remote Touch ScreenPneumatic Slide Gate Below Mixer Safety Circuit Standards Safety Devices and InterlocksFail Safe Operation Safety Device Lock-OutsTwist Cap Plug Electric Safety Interlock Switch All ModelsRigging and Placing the Unit InstallationMounting Configuration Uncrating the EquipmentMachine Mount Mezzanine Mounted Batch Blender Mezzanine MountTypical Central Blender Layout Floor Mount Central BlenderMechanical Installation Electrical InstallationCustomer-Supplied Components Pneumatic InstallationWeigh Hopper Installation Slide Gate Models only Set-upStroke Limiters for Metering Gates Load Cell Mechanical Stop Adjustment Load Cell AdjustmentLogo Final ConnectionsController Setup Recipe Entry FormatsRecipe Format Menu Quickset Mode Most common in injection molding Percentage Mode Most common in extrusion and blow molding Feeder Metering Order Parts Mode Often used in Compounding ApplicationsSwitching Modes Current Recipe MenuInventory Shutdown Batch Size MenuBatch Ready Mode AutoStart FeatureWeigh Every Batch Every Second Batch Every Third BatchEvery Fourth Batch Printer Features Blender Calibration Batch Interval or Timed Interval PrintoutPrint Inventory Display Time and DatePage Why Blender Calibration is Necessary Feeder Calibration Auger Blenders Re-Mix Timer Mix TimerWeigh Hopper Dump Delay Time Weigh Hopper Dump TimeWeigh Hopper Dump Cycle Timed Mixing Option Setting Date & TimeFeeder Alarm Setup & Flags Mixer OptionsMAX Hopper Weight Exceeded Power Interruption Additional settings that usually do not have to be changed Network Communications Baud Rate & I.D. SettingsShutting Down Blender Initial StartupGeneral Operation Quick Start ProcedureOperation Start-upExisting Recipes Display Description LCD Controller Description & OperationRecipe Page Start Slide Gate & Auger Blender Control System Menu StructureRecipe Book Storage Menus Control FunctionsErase Recipe or Entire Book Display Recipe ContentsSave Running Recipe to the Book Load a Saved Recipe from the BookFeeder Clean Out Color Changes Page Standard Run Time Displays Shutting Down the Blender Maintenance Preventative Maintenance SchedulePhotocopy this page for your maintenance records Internal Components of the Control Panel Preventative MaintenanceCorrective Maintenance ElectricalOutput Signals from Programmable Controller Input Signals to Programmable ControllerPneumatic System Maintenance Troubleshooting Problem Corrective actionIntroduction ±10%. This voltage must remain constant with all the motors Problem Corrective action Warranty will be voided Problem Corrective action Warranty Liabilities WarrantyWarranty Specifications Warranty RestrictionsTechnical Specifications Customer ResponsibilitiesAnnex B Information Auger Blender -E Series Specifications Slide Gate Blender -E Series SpecificationsSlide Gate Gravimetric Batch Blending Systems Drawings & DiagramsSpare Parts List Typical Slide Gate Model Assembly OverviewModel 4000 Auger Gravimetric Batch Blending SystemsModel 002 with Opti-Mixer Model 012 with Opti-Mixer Model 012 with Rotary HC mixerModel 012 with Common Feeder Components Model 060 with Rotary HC Mixer Model 060 with OptimixerModel 060 with Common Feeder Components Typical Mixer Section Front Typical Opti-Mixer Front Assembly DetailTypical Mixer Section Rear Typical Opti-Mixer Rear Assembly DetailTypical Mixer Frame Typical Opti-Mixer Frame AssemblyTypical Slide Gate Diamond Gate Assembly Detail Typical Gate AssemblyTypical Supply Hopper Typical Slide Gate-014 Series Hopper Assembly DetailTypical Weigh Hopper & Load Cell Detail Technical Assistance Blender Identification Serial Number TagAddendum Service Supervisor InformationProgrammable Settings Factory Setup Menu Available SelectionsFeed Algorithm Options Screen Advanced Weight Options ScreenMechanical Options Screen Feed Calibration Options ScreenUnits Feeder SetupCustomer Setup Menu Network SetupAlarm Log Alarm SetupMaintenance Password Programmable FeaturesPasswords User Password

A0567659 specifications

Mitsubishi Electronics A0567659 is an advanced display module that embodies the cutting-edge technology and innovation that Mitsubishi is renowned for. Designed primarily for industrial applications, this display module stands out due to its robust performance and exceptional image quality, making it an ideal choice for various sectors including automation, transportation, and manufacturing.

One of the main features of the A0567659 is its high-resolution display capability. With a resolution that provides clear and detailed visuals, users can expect enhanced readability and precision in their data visualization tasks. This is particularly important in industrial environments where the accuracy of information can significantly impact operational efficiency.

The display utilizes advanced LCD technology, ensuring vibrant colors and high contrast ratios that make the content easily viewable under different lighting conditions. The screen's brightness is adjustable, allowing users to customize their visual experience according to the specific needs of their workplace. The durability of the A0567659 is another highlight, as it is built to withstand harsh conditions including extreme temperatures and exposure to dust and moisture. This ruggedness is essential for maintaining long-term performance in demanding environments.

In terms of connectivity, the A0567659 is equipped with multiple interfaces, making it versatile for integration with various systems. Whether it’s connecting to a PLC, computer, or other control devices, users can benefit from seamless communication across their technological ecosystem. This feature underlines Mitsubishi's focus on facilitating smooth integration within existing infrastructures.

Another significant characteristic is its energy efficiency. The A0567659 is designed to consume less power while delivering high performance, aligning with the growing trend of sustainable technology solutions. This aspect not only helps in reducing operational costs but also makes it an environmentally friendly choice for businesses looking to minimize their carbon footprint.

Furthermore, Mitsubishi Electronics places a strong emphasis on user-friendliness. The display module is designed with an intuitive interface that simplifies the operation for users at all skill levels. This ease of use, combined with thorough documentation and support, ensures that users can harness the full potential of the A0567659 without extensive training or technical expertise.

In conclusion, the Mitsubishi Electronics A0567659 is a powerful display module characterized by its high-resolution display, durability, versatile connectivity, and energy efficiency. It represents a robust solution for industries that demand reliable and high-quality visual communication tools.
Top Page Image Contents