Mitsubishi Electronics A0567659 specifications Electrical Installation, Mechanical Installation

Page 32

Mechanical Installation

The installation procedure should be used as a general guideline for the proper installation steps required to install the Slide Gate/Auger blending system.

1.Lift blender and position over machine throat or floor stand.

2.Set in position and secure by tightening four bolts.

3.Remove lifting strap.

4.Mount the material conveying system receivers on the top of the blender supply hoppers.

5.Align the weigh hopper on the load cell brackets. Carefully adjust the load cell brackets to ensure that the weigh hopper is centered on the brackets without rocking. If for some reason the locating tabs do not align with the weigh hopper, they can easily be loosened and adjusted.

Note: Use extreme care when tightening bolts on top of the load cells so you do not spring the load cells. The load cells are extremely delicate and should be treated with care!

6.Check the slide gate metering assemblies to ensure they are not damaged, and will slide back and forth freely. These are the most important items on the blender, besides the load cell and weigh hopper assemblies.

3-3 Electrical Installation

The standard Slide Gate/Auger blending system is designed to operate on 120/1/60 supply voltage (220/1/50 CE models are also available). The current requirements vary with the blender’s size and throughput rating. For exact current requirements, check the blender serial number tag, located on the rear plate of the mixer section.

If a step down transformer was provided, it should never be used to power anything other than the blender. Loading equipment, etc. must be powered by another power source. As well as possibly overloading the transformer, the additional equipment may induce power line noise that may affect the operation of the blending system.

The transformer will be mounted and wired by the customer or your installer. If company or local codes require fusing or disconnects, these items must be supplied, wired, and mounted by the customer.

Note: Each blending system MUST be connected to a separate source of power. Do not connect other electrical equipment, especially self-contained hopper loaders, on the same line as the blending system.

Ensure that the power entrance location on the blender panel remains unchanged. Make sure that the proper size wire and proper wire routing techniques are used when installing the supply wiring to the control panel. Care must be taken to ensure that the supply wiring does not interfere with the low voltage DC wiring.

The blender is equipped with a plug that functions as the disconnect device (See Figure 11 on Page 25 for an example). The mating receptacle must be installed no higher than 5’ feet

(1.6 m) above the floor. Make sure your installation conforms to your regional electrical standards.

Gravimetric Batch Blenders w/Mitsubishi Control

Chapter 3: Installation

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Write Down Your Serial Numbers Here For Future Reference Shipping Information Warranty Returns Credit ReturnsTable of Contents Troubleshooting Addendum Safety Symbols Used in this Manual SafetyHow to Use This Manual Gravimetric Batch Blender Safety Tags Description Follow all Safety Codes Wear Safety Glasses and Work GlovesResponsibility General ResponsibilityOperator Responsibility RememberMaintenance Responsibility Reporting a Safety DefectAccessories Customer ServiceFunctional Description Models Covered in This ManualBoth Blender Styles Typical Features & ComponentsMechanical Features Controller Features Blender Controller shown with Mitsubishi Touch ScreenSlide Gate & Auger Blender System Component Description Material Supply HoppersSlide Gate Metering Assemblies Slide Gate Blenders Auger Metering Assemblies Auger Blenders available with a Choice of MixersWeigh Hopper Typical Weigh HopperWeigh Hopper Discharge Valve Mix ChamberOpti-Mixer HC MixerOperator Control Panel Controller Pushbutton & Touchscreen Tags Button FunctionTypical Setup Screens Logo Pneumatic Slide Gate Below Mixer OptionsRemote Touch Screen Safety Devices and Interlocks Safety Circuit StandardsSafety Device Lock-Outs Fail Safe OperationElectric Safety Interlock Switch All Models Twist Cap PlugInstallation Mounting ConfigurationUncrating the Equipment Rigging and Placing the UnitMachine Mount Mezzanine Mount Mezzanine Mounted Batch BlenderFloor Mount Central Blender Typical Central Blender LayoutElectrical Installation Mechanical InstallationPneumatic Installation Customer-Supplied ComponentsStroke Limiters for Metering Gates Weigh Hopper Installation Slide Gate Models onlySet-up Load Cell Adjustment Load Cell Mechanical Stop AdjustmentFinal Connections LogoRecipe Format Menu Controller SetupRecipe Entry Formats Quickset Mode Most common in injection molding Percentage Mode Most common in extrusion and blow molding Parts Mode Often used in Compounding Applications Switching ModesCurrent Recipe Menu Feeder Metering OrderBatch Size Menu Inventory ShutdownWeigh Every Batch Batch Ready ModeAutoStart Feature Every Fourth Batch Every Second BatchEvery Third Batch Printer Features Batch Interval or Timed Interval Printout Print InventoryDisplay Time and Date Blender CalibrationPage Why Blender Calibration is Necessary Feeder Calibration Auger Blenders Mix Timer Re-Mix TimerWeigh Hopper Dump Cycle Weigh Hopper Dump Delay TimeWeigh Hopper Dump Time Setting Date & Time Feeder Alarm Setup & FlagsMixer Options Timed Mixing OptionMAX Hopper Weight Exceeded Power Interruption Network Communications Baud Rate & I.D. Settings Additional settings that usually do not have to be changedInitial Startup Shutting Down BlenderQuick Start Procedure OperationStart-up General OperationExisting Recipes Controller Description & Operation Display Description LCDSlide Gate & Auger Blender Control System Menu Structure Recipe Page StartControl Functions Recipe Book Storage MenusDisplay Recipe Contents Save Running Recipe to the BookLoad a Saved Recipe from the Book Erase Recipe or Entire BookFeeder Clean Out Color Changes Page Standard Run Time Displays Shutting Down the Blender Photocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Preventative Maintenance Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerPneumatic System Maintenance Introduction TroubleshootingProblem Corrective action ±10%. This voltage must remain constant with all the motors Problem Corrective action Warranty will be voided Problem Corrective action Warranty Warranty SpecificationsWarranty Restrictions Warranty LiabilitiesAnnex B Information Technical SpecificationsCustomer Responsibilities Slide Gate Blender -E Series Specifications Auger Blender -E Series SpecificationsDrawings & Diagrams Spare Parts ListTypical Slide Gate Model Assembly Overview Slide Gate Gravimetric Batch Blending SystemsModel 002 with Opti-Mixer Model 4000Auger Gravimetric Batch Blending Systems Model 012 with Common Feeder Components Model 012 with Opti-MixerModel 012 with Rotary HC mixer Model 060 with Optimixer Model 060 with Rotary HC MixerModel 060 with Common Feeder Components Typical Opti-Mixer Front Assembly Detail Typical Mixer Section FrontTypical Opti-Mixer Rear Assembly Detail Typical Mixer Section RearTypical Opti-Mixer Frame Assembly Typical Mixer FrameTypical Gate Assembly Typical Slide Gate Diamond Gate Assembly DetailTypical Slide Gate-014 Series Hopper Assembly Detail Typical Supply HopperTypical Weigh Hopper & Load Cell Detail Blender Identification Serial Number Tag Technical AssistanceService Supervisor Information Programmable SettingsFactory Setup Menu Available Selections AddendumAdvanced Weight Options Screen Feed Algorithm Options ScreenFeed Calibration Options Screen Mechanical Options ScreenFeeder Setup Customer Setup MenuNetwork Setup UnitsAlarm Setup Alarm LogProgrammable Features PasswordsUser Password Maintenance Password

A0567659 specifications

Mitsubishi Electronics A0567659 is an advanced display module that embodies the cutting-edge technology and innovation that Mitsubishi is renowned for. Designed primarily for industrial applications, this display module stands out due to its robust performance and exceptional image quality, making it an ideal choice for various sectors including automation, transportation, and manufacturing.

One of the main features of the A0567659 is its high-resolution display capability. With a resolution that provides clear and detailed visuals, users can expect enhanced readability and precision in their data visualization tasks. This is particularly important in industrial environments where the accuracy of information can significantly impact operational efficiency.

The display utilizes advanced LCD technology, ensuring vibrant colors and high contrast ratios that make the content easily viewable under different lighting conditions. The screen's brightness is adjustable, allowing users to customize their visual experience according to the specific needs of their workplace. The durability of the A0567659 is another highlight, as it is built to withstand harsh conditions including extreme temperatures and exposure to dust and moisture. This ruggedness is essential for maintaining long-term performance in demanding environments.

In terms of connectivity, the A0567659 is equipped with multiple interfaces, making it versatile for integration with various systems. Whether it’s connecting to a PLC, computer, or other control devices, users can benefit from seamless communication across their technological ecosystem. This feature underlines Mitsubishi's focus on facilitating smooth integration within existing infrastructures.

Another significant characteristic is its energy efficiency. The A0567659 is designed to consume less power while delivering high performance, aligning with the growing trend of sustainable technology solutions. This aspect not only helps in reducing operational costs but also makes it an environmentally friendly choice for businesses looking to minimize their carbon footprint.

Furthermore, Mitsubishi Electronics places a strong emphasis on user-friendliness. The display module is designed with an intuitive interface that simplifies the operation for users at all skill levels. This ease of use, combined with thorough documentation and support, ensures that users can harness the full potential of the A0567659 without extensive training or technical expertise.

In conclusion, the Mitsubishi Electronics A0567659 is a powerful display module characterized by its high-resolution display, durability, versatile connectivity, and energy efficiency. It represents a robust solution for industries that demand reliable and high-quality visual communication tools.
Top Page Image Contents