Mitsubishi Electronics 882.00273.00 specifications Inventory Info

Page 96

INVENTORY INFO

1 (RW) clear_inventory,M503 (toggle this to clear all inventory, you must also reset this bit after completion)

2(RW) batch_counter,D1336,LONG VALUE (number of batches made)

3(R) hop1_inventory,D1274,LONG VALUE (this is the whole portion of the inventory)

4(R) hop2_inventory,D1276,LONG VALUE (this is the whole portion of the inventory)

5(R) hop3_inventory,D1278,LONG VALUE (this is the whole portion of the inventory)

6(R) hop4_inventory,D1280,LONG VALUE (this is the whole portion of the inventory)

7(R) hop5_inventory,D1282,LONG VALUE (this is the whole portion of the inventory)

8(R) hop6_inventory,D1284,LONG VALUE (this is the whole portion of the inventory)

9(R)batch_inventory,D1344,LONG VALUE (this is the whole portion of the inventory)

10(R) hop1_fractional_inventory,D1306,LONG VALUE (this is the fractional part of the inventory .xxx)

11(R) hop2_fractional_inventory,D1308,LONG VALUE (this is the fractional part of the inventory .xxx)

12(R) hop3_fractional_inventory,D1310,LONG VALUE (this is the fractional part of the inventory .xxx)

13(R) hop4_fractional_inventory,D1312,LONG VALUE (this is the fractional part of the inventory .xxx)

14(R) hop5_fractional_inventory,D1314,LONG VALUE (this is the fractional part of the inventory .xxx)

15(R) hop6_fractional_inventory,D1316,LONG VALUE (this is the fractional part of the inventory .xxx)

16(R) batch_inventory_decimal_part,D1352,LONG VALUE (this is the fractional part of the inventory

.xxx)

BF1-615.3

Chapter 7: 6BAppendix

96 of 101

Image 96

Contents Write Down Your Serial Numbers Here For Future Reference Gravimetric Slide Gate Batch Blender Mitsubishi ControllerPart Number Bulletin Number BF1-615.3 Effective 11/07/07 We are committed to a continuing program of product improvementShipping Info Unpacking and InspectionIn the Event of Shipping Damage If the Shipment is Not CompleteWarranty Returns Credit ReturnsTable of Contents CHAPTER 1 SAFETYCHAPTER 3 INSTALLATION CHAPTER 2 FUNCTIONAL DESCRIPTIONCHAPTER 5 MAINTENANCE CHAPTER 6 TROUBLESHOOTINGCHAPTER 4 OPERATION CHAPTER 7 APPENDIXHopper Additive Feeder Sub-Assembly Optional Chapter 1 Safety 1-1 How to Use This ManualSafety Symbols Used in this Manual Figure 1 Safety Tags and Warning Labels Description1-2 Warnings and Precautions CAUSING BODILY INJURY EXISTS ANY TIME THE POWER IS ONWear SAFETY GLASSES and WORK GLOVES Use care when LOADING, UNLOADING, RIGGING, or MOVING this equipment1-3 Responsibility General ResponsibilityOperator Responsibility REMEMBER Maintenance Responsibility Reporting a Safety DefectAccessories Customer ServiceChapter 2 Functional Description 2-1 Models Covered in This ManualFigure 2 Equipment Specifications Figure 3 Typical Blender AssemblyDimensions and Specifications 25002-3 Typical Features and Components Mechanical FeaturesController Features Figure 4 Typical Mitsubishi Controller Touch Screen DisplayFigure 5 Typical Hopper Assembly System Component DescriptionSupply Hoppers Slide Gates Figure 6 Typical Slide Gate Assembly Weigh HopperFigure 7 Typical Weigh Hopper Assembly Figure 8 Typical Mixer Assembly Mix ChamberOperator Control Panel Display Figure 9 Typical Mitsubishi Controller Touch Screen Display Figure 10 Controller Pushbuttons & Touchscreen TagsButton FunctionFigure 11 Typical Operator Screens 22 ofFigure 12 Typical Setup Screens 23 of24 of Figure 13 Mixer Slide Gate Switch Positions 2-4 Optional ComponentsPneumatic Slide Gate below Mixer PositionFigure 15 Typical R.A.M. Hopper Blender Configuration Figure 16 Typical Additive Feeder ConfigurationRegrind Auger Metering R.A.M. Hopper Additive Feeder Hopper2-5 Safety Features Safety Circuit StandardsSafety Device Lock-Outs Fail Safe OperationFigure 17 Electrical Disconnect Plug Twist Cap Plug Connected to Each Feeder Auger MotorFigure 18 Twist Cap Plug Electric Safety Interlock Switch Figure 19 Electrical Safety Interlock Switch Located on mixer doorChapter 3 Installation 3-2 Mechanical Installation3-1 Uncrating the Equipment Figure 20 Blender Lifting Lugs 1 on each sideMounting Configurations Site RequirementsMachine Mount Note Larger blenders need to be braced as part of the installation Mezzanine MountFigure 21 Typical Mezzanine Mounted Batch Blender GRAVIMETRIC BATCH BLENDER MEZZANINE SUPPLIED BY CUSTOMERFloor Mount Central Blender Figure 22 Typical Floor Mount Central Blender Layout3-3 Electrical Connections 3-4 Pneumatic ConnectionsFigure 23 Customer-Supplied Pneumatic Components 3-5 Initial Set-up Mechanical Set-upStroke Limiters for Metering Gates Figure 24 Stroke LimitersWeigh Hopper Installation Figure 25 Weigh HopperFinal Connections Figure 26 Display Startup ScreenFigure 27 Display Main Recipe Screen Controller Set-upBlender Controller Menu Structure Blender Calibration Figure 28 Display Calibration Menu Screen Figure 29 Display Calibration ScreenEnter in the Calibration Weight Press here to perform the calibration Current Loadcell Bits Follow InstructionsAlarm Setup Figure 30 Display Alarm Flags & Feeder Setup ScreenFeeder Calibration Auger Blenders Select a Feeder to Configure Change the Alarm Silence DelayNetwork Setup Figure 31 Ethernet Setup ScreenSetting Date and Time Figure 32 PanelView Configuration ScreenAdditional Setup Parameters 3-6 Initial Startup Quick Start Procedure Chapter 4 Operation4-1 Start-up General Operation4-2 Operation Procedures Existing RecipesNote Press “Push to Start or Stop” button to start blender Operator Displays Figure 33 Typical Recipe Entry Operator ScreenFigure 34 Typical Manual Control Operator Screen Figure 35 Typical Inventory Display Operator Screen Recipe Entry FormatsRecipe Format Menu “Quickset” Mode Most common in injection molding Page Switching Modes Recipe Setup“Percentage” Mode Most common in extrusion and blow molding Figure 37 Example Calculations of a 4-component blend in “Parts” modeFigure 38 Typical Batch Sizes BlenderBatch Size lbs Inventory ShutdownAuto Start Feature Mixer and Dump SetupMix Timer Figure 40 Typical Mixer and Dump Setup Operator ScreenRe-Mix Timer Weigh Hopper Dump TimeWeigh Hopper Dump Delay Time Alarm Flags Figure 41 Typical “Out of Material” Alarm ScreenWeigh Hopper Dump Cycle Mixer Dump TimeFigure 42 Typical “Maximum Hopper Weight” Alarm Screen MAX HOPPER WEIGHT EXCEEDED check batch sizeFigure 43 Typical “Calibration Error” Alarm Screen Figure 44 Typical “Power Interruption” Alarm ScreenFigure 45 Typical “PLC Battery Low” Alarm Screen PLC BATTERY LOWFigure 46 Typical “E-Stop Activated” Alarm Screen Feeder Clean Out Figure 47 Typical Manual Control Operator ScreenRecipe Book Tree Diagram in section 3-5 of this manualDisplay Recipe Contents Figure 48 Typical Recipe Book Operator ScreenSave Running Recipe to the Book Load a Saved Recipe from the BookErase Recipe or Entire Book Color Changes4-3 Shut-down Figure 49 Typical Inventory Shutdown Operator ScreenChapter 5 Maintenance 5-1 Preventative Maintenance ScheduleFigure 50 Sample Preventative Maintenance Schedule System model #5-2 Preventative Maintenance 5-3 Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerNote The alarm contact has a maximum load of 3 amps Chapter 6 Troubleshooting Problem6-1 Introduction Corrective actionProblem Corrective actionProblem warranty will be voided Service Department 7-1 Technical Specifications Equipment SpecificationsFigure 52 Equipment Specifications Chapter 7 AppendixAnnex B Information 7-2 Drawings and Diagrams Final AssemblyFigure 53 Typical Final Assembly Parts List Mixer Sub-Assembly 75 ofFigure 54 Typical Mixer Assembly Parts List A0770319Hopper Sub-assembly Figure 55 Typical Hopper Assembly Parts ListHopper R.A.M. Regrind Auger Metering Sub-Assembly Optional Figure 56 Typical R.A.M. Hopper Assembly Parts ListHopper Additive Feeder Sub-Assembly Optional Figure 57 Typical Additive Feeder Hopper Assembly Parts ListWeigh Hopper Sub-assembly Figure 58 Typical Weigh Hopper Assembly Parts ListSlide Gate Sub-assembly Figure 59 Typical Slidegate Assembly Parts ListKnife Gate Sub-assembly HD Optional Figure 60 Typical Knife Gate below mixer Assembly Parts ListKnife Gate Sub-assembly RD Optional Figure 61 Typical Knife Gate floor stand Assembly Parts ListFigure 62 Typical Mitsubishi Controller Main Parts List Figure 63 Typical Mitsubishi Display Main Parts ListControl Panel Layout Figure 64 Blender Spare Parts Listing Spare Parts Kits7-4 Addendum Service Supervisor Information PasswordsProgrammable Settings Figure 65 Typical Operator Setup ScreenFigure 66 Typical Engineering Only Setup Screen Factory Setup MenuAdvanced Weight Options Screen Metering Test ScreenFigure 68 Typical Advanced Weight Options Screen Feed Algorithm Options ScreenFigure 69 Typical Feed Algorithm Options Screen Feed Calibration Options ScreenFeeder Setup Figure 72 Typical Feeder Setup ScreenMechanical Options Screen Figure 71 Typical Mechanical Options ScreenCustomer Setup Menu Figure 74 Typical Ethernet Setup ScreenUnits Figure 73 Typical Units ScreenFigure 75 Typical Alarm Flags & Feeder Setup Screen Alarm LogFigure 76 Typical Alarm Log Screen Factory Default Setup Parameters BF1-615.3Chapter 7 6BAppendix 92 of93 of VIRGIN7-5 Mitsubishi Communications Manual Note ITEMS MARKED R ARE READ ONLY AND ITEMS MARKED RW ARE READ/WRITEGENERAL BLENDER INFO BLENDER STARTING AND STOPPINGBLENDER ALARMS INVENTORY INFO RECIPE INFO THIS IS WHERE YOU RIGHT THE NEW RECIPE TO CURRENT RECIPE INFO THIS IS THE RECIPE THAT IS CURRENTLY BEING MADETARGETS VS. ACTUAL WEIGHT INFO RECIPE BOOK MANIPULATIONAlarm Number Explanation FIXED DECIMAL EXPLANATIONWRITING RECIPE EXPLANATION RECORDING THE TARGETS VS. ACTUALS FOR EACH BATCHUNTIL THE HOPPER FEEDS MATERIAL INTO THE NEW BATCH Service Department 7-6 Technical AssistanceParts Department Sales Department