Mitsubishi Electronics 882.00273.00 Feeder Clean Out, Typical Manual Control Operator Screen

Page 59
Feeder Clean Out

Feeder Clean Out

Any feeder in the Slide Gate/Auger blending system can be emptied and refilled with a different material. To do a feeder clean out, the operator has to press the “Clean Out” icon key from the recipe screen (the first screen that appears on power up).

This screen will allow you to Open or Close the Feeder, Weigh Hopper, Mixer Knife Gate, Empty the Entire Blender, Start or Stop the Mixer Motor, Test the Alarm Output, Find out the Mixer Proximity Status and monitor the Current Hopper Weight.

Figure 47: Typical Manual Control Operator Screen

Open or Close

Feeder

Open or Close

Weigh Hopper

Start or Stop Mixer Motor

Open or Close Mixer Knife Gate

Test Alarm

Output

Low Level Prox Status

Empty Entire

Blender

Warning Message

Current Hopper Weight

Go back to Setup Directory

The dump valve opens as soon as the “Press to Open Feeder” key is pressed. This easy feeder clean out option also serves as a means for emptying a batch that is held in the weigh hopper if the “Press to Open Weigh Hopper” key is pressed when the blender is stopped. To open/close feeder numbers 2, 3, 4, 5 & 6 press the number next to “Press to Open Feeder” to select the feeder you desire to empty and the “Press to Close Feeder” key to close the dump valve. Touch the “Done” key to return to the recipe menu. After entering a recipe, the operator will restart the blending system, putting it back in normal operation.

Note: Before starting Slide Gate/Auger blending systems, each ingredient hopper in the current recipe must contain material! Virgin material must be loaded in hopper #1 and hopper #3 should only be used for regrind!!

Once the operator initiates the run mode of operation, the blending system controller will begin monitoring the mixer high-level switch. Nothing will happen until the mixer high-level switch is uncovered. This tells the controller that the mixing chamber is capable of holding another batch of material.

Once the mixer high-level switch is uncovered, and the weigh hopper has dumped, the system will meter the ingredients from the supply hoppers, through the metering units, into the weigh hopper. Each component will be metered individually to allow accurate weighing of the material.

Each component is metered in the order specified by the “Metering Order” setup. See the Installation & Setup chapter for further details.

Once the final ingredient specified in the recipe has been metered into the weigh hopper, the controller will take a final weight reading of the weigh hopper. This will start the “Dump

BF1-615.3

Chapter 4: 3BOperation

59 of 101

Page 58 Page 60
Image 59
Page 58 Page 60
Contents We are committed to a continuing program of product improvement Write Down Your Serial Numbers Here For Future ReferenceGravimetric Slide Gate Batch Blender Mitsubishi Controller Part Number Bulletin Number BF1-615.3 Effective 11/07/07If the Shipment is Not Complete Shipping InfoUnpacking and Inspection In the Event of Shipping DamageCredit Returns Warranty ReturnsCHAPTER 2 FUNCTIONAL DESCRIPTION Table of ContentsCHAPTER 1 SAFETY CHAPTER 3 INSTALLATIONCHAPTER 7 APPENDIX CHAPTER 5 MAINTENANCECHAPTER 6 TROUBLESHOOTING CHAPTER 4 OPERATIONHopper Additive Feeder Sub-Assembly Optional Safety Symbols Used in this Manual Chapter 1 Safety1-1 How to Use This Manual Description Figure 1 Safety Tags and Warning LabelsUse care when LOADING, UNLOADING, RIGGING, or MOVING this equipment 1-2 Warnings and PrecautionsCAUSING BODILY INJURY EXISTS ANY TIME THE POWER IS ON Wear SAFETY GLASSES and WORK GLOVESOperator Responsibility 1-3 ResponsibilityGeneral Responsibility REMEMBER Reporting a Safety Defect Maintenance Responsibility2-1 Models Covered in This Manual AccessoriesCustomer Service Chapter 2 Functional Description2500 Figure 2 Equipment SpecificationsFigure 3 Typical Blender Assembly Dimensions and SpecificationsFigure 4 Typical Mitsubishi Controller Touch Screen Display 2-3 Typical Features and ComponentsMechanical Features Controller FeaturesSupply Hoppers Figure 5 Typical Hopper AssemblySystem Component Description Slide Gates Weigh Hopper Figure 6 Typical Slide Gate AssemblyFigure 7 Typical Weigh Hopper Assembly Operator Control Panel Display Figure 8 Typical Mixer AssemblyMix Chamber Function Figure 9 Typical Mitsubishi Controller Touch Screen DisplayFigure 10 Controller Pushbuttons & Touchscreen Tags Button22 of Figure 11 Typical Operator Screens23 of Figure 12 Typical Setup Screens24 of Position Figure 13 Mixer Slide Gate Switch Positions2-4 Optional Components Pneumatic Slide Gate below MixerAdditive Feeder Hopper Figure 15 Typical R.A.M. Hopper Blender ConfigurationFigure 16 Typical Additive Feeder Configuration Regrind Auger Metering R.A.M. HopperFail Safe Operation 2-5 Safety FeaturesSafety Circuit Standards Safety Device Lock-OutsFigure 18 Twist Cap Plug Figure 17 Electrical Disconnect PlugTwist Cap Plug Connected to Each Feeder Auger Motor Figure 19 Electrical Safety Interlock Switch Located on mixer door Electric Safety Interlock SwitchFigure 20 Blender Lifting Lugs 1 on each side Chapter 3 Installation3-2 Mechanical Installation 3-1 Uncrating the EquipmentMachine Mount Mounting ConfigurationsSite Requirements GRAVIMETRIC BATCH BLENDER MEZZANINE SUPPLIED BY CUSTOMER Note Larger blenders need to be braced as part of the installationMezzanine Mount Figure 21 Typical Mezzanine Mounted Batch BlenderFigure 22 Typical Floor Mount Central Blender Layout Floor Mount Central BlenderFigure 23 Customer-Supplied Pneumatic Components 3-3 Electrical Connections3-4 Pneumatic Connections Figure 24 Stroke Limiters 3-5 Initial Set-upMechanical Set-up Stroke Limiters for Metering GatesFigure 26 Display Startup Screen Weigh Hopper InstallationFigure 25 Weigh Hopper Final ConnectionsController Set-up Figure 27 Display Main Recipe ScreenBlender Controller Menu Structure Blender Calibration Current Loadcell Bits Follow Instructions Figure 28 Display Calibration Menu ScreenFigure 29 Display Calibration Screen Enter in the Calibration Weight Press here to perform the calibrationSelect a Feeder to Configure Change the Alarm Silence Delay Alarm SetupFigure 30 Display Alarm Flags & Feeder Setup Screen Feeder Calibration Auger BlendersFigure 32 PanelView Configuration Screen Network SetupFigure 31 Ethernet Setup Screen Setting Date and TimeAdditional Setup Parameters 3-6 Initial Startup General Operation Quick Start ProcedureChapter 4 Operation 4-1 Start-upNote Press “Push to Start or Stop” button to start blender 4-2 Operation ProceduresExisting Recipes Figure 34 Typical Manual Control Operator Screen Operator DisplaysFigure 33 Typical Recipe Entry Operator Screen Recipe Entry Formats Figure 35 Typical Inventory Display Operator ScreenRecipe Format Menu “Quickset” Mode Most common in injection molding Page Figure 37 Example Calculations of a 4-component blend in “Parts” mode Switching ModesRecipe Setup “Percentage” Mode Most common in extrusion and blow moldingInventory Shutdown Figure 38 Typical Batch SizesBlender Batch Size lbsFigure 40 Typical Mixer and Dump Setup Operator Screen Auto Start FeatureMixer and Dump Setup Mix TimerWeigh Hopper Dump Delay Time Re-Mix TimerWeigh Hopper Dump Time Mixer Dump Time Alarm FlagsFigure 41 Typical “Out of Material” Alarm Screen Weigh Hopper Dump CycleFigure 44 Typical “Power Interruption” Alarm Screen Figure 42 Typical “Maximum Hopper Weight” Alarm ScreenMAX HOPPER WEIGHT EXCEEDED check batch size Figure 43 Typical “Calibration Error” Alarm ScreenFigure 46 Typical “E-Stop Activated” Alarm Screen Figure 45 Typical “PLC Battery Low” Alarm ScreenPLC BATTERY LOW Figure 47 Typical Manual Control Operator Screen Feeder Clean OutTree Diagram in section 3-5 of this manual Recipe BookLoad a Saved Recipe from the Book Display Recipe ContentsFigure 48 Typical Recipe Book Operator Screen Save Running Recipe to the BookColor Changes Erase Recipe or Entire BookFigure 49 Typical Inventory Shutdown Operator Screen 4-3 Shut-downSystem model # Chapter 5 Maintenance5-1 Preventative Maintenance Schedule Figure 50 Sample Preventative Maintenance ScheduleInternal Components of the Control Panel 5-2 Preventative Maintenance5-3 Corrective Maintenance ElectricalNote The alarm contact has a maximum load of 3 amps Input Signals to Programmable ControllerOutput Signals from Programmable Controller Corrective action Chapter 6 TroubleshootingProblem 6-1 IntroductionCorrective action ProblemCorrective action warranty will be voided Service Department Chapter 7 Appendix 7-1 Technical SpecificationsEquipment Specifications Figure 52 Equipment SpecificationsAnnex B Information Figure 53 Typical Final Assembly Parts List 7-2 Drawings and DiagramsFinal Assembly 75 of Mixer Sub-AssemblyA0770319 Figure 54 Typical Mixer Assembly Parts ListFigure 55 Typical Hopper Assembly Parts List Hopper Sub-assemblyFigure 56 Typical R.A.M. Hopper Assembly Parts List Hopper R.A.M. Regrind Auger Metering Sub-Assembly OptionalFigure 57 Typical Additive Feeder Hopper Assembly Parts List Hopper Additive Feeder Sub-Assembly OptionalFigure 58 Typical Weigh Hopper Assembly Parts List Weigh Hopper Sub-assemblyFigure 59 Typical Slidegate Assembly Parts List Slide Gate Sub-assemblyFigure 60 Typical Knife Gate below mixer Assembly Parts List Knife Gate Sub-assembly HD OptionalFigure 61 Typical Knife Gate floor stand Assembly Parts List Knife Gate Sub-assembly RD OptionalControl Panel Layout Figure 62 Typical Mitsubishi Controller Main Parts ListFigure 63 Typical Mitsubishi Display Main Parts List Spare Parts Kits Figure 64 Blender Spare Parts ListingFigure 65 Typical Operator Setup Screen 7-4 Addendum Service Supervisor InformationPasswords Programmable SettingsMetering Test Screen Figure 66 Typical Engineering Only Setup ScreenFactory Setup Menu Advanced Weight Options ScreenFeed Calibration Options Screen Figure 68 Typical Advanced Weight Options ScreenFeed Algorithm Options Screen Figure 69 Typical Feed Algorithm Options ScreenFigure 71 Typical Mechanical Options Screen Feeder SetupFigure 72 Typical Feeder Setup Screen Mechanical Options ScreenFigure 73 Typical Units Screen Customer Setup MenuFigure 74 Typical Ethernet Setup Screen UnitsFigure 76 Typical Alarm Log Screen Figure 75 Typical Alarm Flags & Feeder Setup ScreenAlarm Log 92 of Factory Default Setup ParametersBF1-615.3 Chapter 7 6BAppendixVIRGIN 93 ofBLENDER STARTING AND STOPPING 7-5 Mitsubishi Communications ManualNote ITEMS MARKED R ARE READ ONLY AND ITEMS MARKED RW ARE READ/WRITE GENERAL BLENDER INFOBLENDER ALARMS INVENTORY INFO CURRENT RECIPE INFO THIS IS THE RECIPE THAT IS CURRENTLY BEING MADE RECIPE INFO THIS IS WHERE YOU RIGHT THE NEW RECIPE TORECIPE BOOK MANIPULATION TARGETS VS. ACTUAL WEIGHT INFOFIXED DECIMAL EXPLANATION Alarm Number ExplanationUNTIL THE HOPPER FEEDS MATERIAL INTO THE NEW BATCH WRITING RECIPE EXPLANATIONRECORDING THE TARGETS VS. ACTUALS FOR EACH BATCH Sales Department Service Department7-6 Technical Assistance Parts Department
Top Page Image Contents