Master Bilt CMICL-156 manual Level Floor, Caulking

Page 9

Figure #5

If locking arm fails to hook locking pin, turn cam-lock counter-clockwise one completes turn and repeat the procedure like Figure #3

LEVEL FLOOR

It is very important that the existing floor be level If it is not level the insulated floor panels must be leveled by shimming between the existing floor and the floor panels. Assembling a walk-in of any type on an uneven or unleveled floor without some sort of shimming of grouting is not practical, not advisable and will never result in a satisfactory installation.

Leveling of floor type walk-in floor panels should be accomplished by the use of a sand leveling bed or the use of shim stock. Shim stock can be rot resistant wood, strips of galvanized sheet metal, etc. Shims under floor panels must be no further than 18” on center in both length and width so as to property support the floor panels when the walk-in is assembled and the product load is in place. Shimming just the outer edges of just the corners of the floor panels will result in broken panels and/or separation of the metal liners from the foam.

CAULKING

Caulking is recommended in all panel joints as shown in Figure #6, #7, and #8. Caulk should be of high- grade outdoor type odorless compound. Approximately one tube of caulk is repaired for every 60 square feet of panel surface.

It should be noted that on walk-ins subject to external weather conditions, the caulking of roof joints does not seal the roof against water penetration. Therefore, a weather protective roof must be installed atop the insulated roof panels.

 

 

 

 

Wall Panel

 

 

Joining

Caulking

Floor Panel

 

 

seam

 

Caulking

of

 

 

Caulking

 

like

 

 

Roof

 

panels

 

 

panel

 

 

 

 

wall

 

 

 

 

panel

 

 

 

 

Figure # 6

 

Figure # 7

 

Figure # 8

Roof to Wall Caulking Detail

Like Panel To Like Panels Caulking Details

 

Floor to Wall Caulking Detail

9

Image 9
Contents Installation & Operations Manual Page Table of Contents Store Conditions IntroductionGround Required For Safe Operation Installation Instructions PRE-INSTALLATION InstructionsInspection for Shipping Damage General InstructionsPanel Storage ElectricalFigure #3 CAM FastenersCaulking Level FloorFloor Assembly Ceiling and Wall Panel AssemblyDoor and Frame Installation Refrigeration Adjusting Door and Replacing HingesTemperature Controls Door Frame Heater ReplacementSet three 30 minutes per 24 hours Final Check ListMASTER-BILT Part Numbers Sale and DisposalOwner Responsibility Page Page Page Page

CMICL-156 specifications

The Master Bilt CMICL-156 is a powerful commercial refrigeration unit designed to meet the demands of various businesses, such as restaurants, grocery stores, and convenience stores. This model excels in providing reliable temperature control, ensuring that perishable goods are stored in optimal conditions.

One of the standout features of the CMICL-156 is its impressive storage capacity. With ample space, it can accommodate large quantities of food and beverages, making it an ideal choice for high-volume operations. The internal shelving is adjustable, which provides flexibility in organization and storage solutions.

This model is equipped with advanced refrigeration technology, allowing for efficient cooling and energy savings. The state-of-the-art compressor ensures rapid temperature recovery, which is crucial for maintaining product quality in busy environments. Additionally, the unit employs a forced air cooling system, promoting consistent temperature distribution throughout the entire cabinet.

Energy efficiency is another central characteristic of the CMICL-156. With its high-efficiency components, this unit not only reduces operational costs but also minimizes its environmental impact. It adheres to eco-friendly standards, helping businesses to maintain a sustainable operation while benefiting from lower energy bills.

The CMICL-156 is designed with user-friendly controls, including a digital display for easy monitoring and adjustments. Operators can quickly set the desired temperature and keep an eye on the internal conditions without hassle. This feature is particularly beneficial in commercial settings where time is of the essence.

Durability is a key aspect of the Master Bilt CMICL-156. Constructed with robust materials, this unit can withstand the rigors of daily use. The stainless steel exterior is not only easy to clean but also resistant to corrosion, ensuring longevity and a professional appearance.

Additionally, the model comes with an LED lighting system, which enhances visibility inside the refrigerator while consuming minimal electricity. This feature allows staff to easily locate and access products, further increasing efficiency during peak service times.

In conclusion, the Master Bilt CMICL-156 combines advanced refrigeration technology, energy efficiency, and durability, making it a top choice for commercial refrigeration needs. Its various features enhance functionality and ease of use, providing businesses with a reliable solution for preserving food and ensuring customer satisfaction.