Master Bilt CMICL-156 manual Door Frame Heater Replacement, Temperature Controls

Page 12

DOOR FRAME HEATER REPLACEMENT

CAUTION: Disconnect main power supply to door of walk-in before beginning the following procedure to avoid electrical shock.

1.Remove stainless steel raceway from around door opening. Possition raceways away from walk-in to allow them to warm to room temperature. This will aid in tape adhesion described below. For freezers, the door power cord must be removed from the light base located on the interior hinge side of the door frame.

2.Disconnect the heater cable lead wires from the power supply inside the light switch J-box and discard heater cable.

3.Feed new heater cable lead wires through the opening in the inner frame and secure grommet in the openning in the back of the ligth switch J-box. Do not connect heater to power supply at this time.

4.Rout heater cable along inside corner of raceway and secure with foil tape. Fasten raceways to door frame as heater cable is secured in place.

5.Route heater cable along inside bed of sill plate as shown. Note diffeence in routing of cooler and freezer heater through sill plate. Again, secure heater cable sith foil tape as if is routed. Special care should be taken not to “kink” heater cable, resulting in improper operation and shortened life of heater. After routing cable through sill plate, position and fasten threshold plate into place.

6.Fasten heater cable lead wires to power supply in light switch J-box and connect main power supply to door frame.

TEMPERATURE CONTROLS

On the CM models, the Temperature Control is on the end penel of the blower housing. These controls have an “off” position ( at full counter-clockwise position) and should be turned clockwise for “colder”.

On the CL models have an Temperture Control mounted on the front of the Blower housing. The left control is the Temperature Control and should be turned clockwise for colder. This control does not hae an “off “ position. There is also another control mounted to the right of the Temperature Control. This control is the “ Defrost Termination-Fan Delay Control “ and shuold be preset to the “ 11:00” position. Counter-clockwise rotation will lengthen defost time; clockwise rotation will decrease defrost time. Turning the knob varies the defrost termination temperature only and has no effect on the (non-adjustable) fan delay.

INSTALLING AND OPERATING DIRECTIONS:

Place start pins in outer (24 hours) dial at the time of day that wsitch countacts are to be reverse from shown when dail pins are opposite time pointer. CAUTION: (Leave at least 1 hole between each adjacent pin).

To set back-up defrost termination: Push down and rotate pointer on inside (2 hours) dial until it is opposite desired time.

To set time of the day: Grasp knob in the outer of the inner (2 hours) dial and rotate it in a counter-clockwise direction. This will revolve the outer dial. Line up the correct time of day on the outer dial with the time pointer. Do not try to set the time control by grasping the outer dial. Rotate the inner dial only.

Fro Replacement: of this control contact Refrigerator manufacture. Master_Bilt (800) 684-8988

12

Image 12
Contents Installation & Operations Manual Page Table of Contents Introduction Store ConditionsGround Required For Safe Operation PRE-INSTALLATION Instructions Installation InstructionsInspection for Shipping Damage General InstructionsElectrical Panel StorageCAM Fasteners Figure #3Level Floor CaulkingFloor Assembly Ceiling and Wall Panel AssemblyDoor and Frame Installation Adjusting Door and Replacing Hinges RefrigerationDoor Frame Heater Replacement Temperature ControlsFinal Check List Set three 30 minutes per 24 hoursMASTER-BILT Part Numbers Sale and DisposalOwner Responsibility Page Page Page Page

CMICL-156 specifications

The Master Bilt CMICL-156 is a powerful commercial refrigeration unit designed to meet the demands of various businesses, such as restaurants, grocery stores, and convenience stores. This model excels in providing reliable temperature control, ensuring that perishable goods are stored in optimal conditions.

One of the standout features of the CMICL-156 is its impressive storage capacity. With ample space, it can accommodate large quantities of food and beverages, making it an ideal choice for high-volume operations. The internal shelving is adjustable, which provides flexibility in organization and storage solutions.

This model is equipped with advanced refrigeration technology, allowing for efficient cooling and energy savings. The state-of-the-art compressor ensures rapid temperature recovery, which is crucial for maintaining product quality in busy environments. Additionally, the unit employs a forced air cooling system, promoting consistent temperature distribution throughout the entire cabinet.

Energy efficiency is another central characteristic of the CMICL-156. With its high-efficiency components, this unit not only reduces operational costs but also minimizes its environmental impact. It adheres to eco-friendly standards, helping businesses to maintain a sustainable operation while benefiting from lower energy bills.

The CMICL-156 is designed with user-friendly controls, including a digital display for easy monitoring and adjustments. Operators can quickly set the desired temperature and keep an eye on the internal conditions without hassle. This feature is particularly beneficial in commercial settings where time is of the essence.

Durability is a key aspect of the Master Bilt CMICL-156. Constructed with robust materials, this unit can withstand the rigors of daily use. The stainless steel exterior is not only easy to clean but also resistant to corrosion, ensuring longevity and a professional appearance.

Additionally, the model comes with an LED lighting system, which enhances visibility inside the refrigerator while consuming minimal electricity. This feature allows staff to easily locate and access products, further increasing efficiency during peak service times.

In conclusion, the Master Bilt CMICL-156 combines advanced refrigeration technology, energy efficiency, and durability, making it a top choice for commercial refrigeration needs. Its various features enhance functionality and ease of use, providing businesses with a reliable solution for preserving food and ensuring customer satisfaction.