U-Line U-2175RCS-22, U-2175RCS-01, U-2175RCS-00 Wood Grille Overlay, Preparation, Installation

Page 16

9 Wood Grille Overlay

Grille Overlay

Your model’s grille is designed to accept a wood grille overlay. An overlay may be used to compliment a door overlay and provides a seamless look for your surrounding decor. Follow the instructions below to prepare and install your grille overlay. Be sure to read over this chapter completely before beginning.

Preparation

!CAUTION

Hook and Loop Fastener Mount

You may also mount your overlay to your grille using hook and loop type fasteners. U-Line recommends using 3M® Dual lock® fasteners. To mount your overlay using a hook and loop fastener follow the instructions below.

1.Read the instructions provided with your hook and loop fastener carefully.

2.Apply hook and loop fastener system to the back of the overlay and front of the grille. Use the shaded areas in the diagram below for application location.

24 Inch Models

Application

The grille overlay MUST have venting as shown in the drawing below. Failure to have proper venting can result in damage to your model.

!CAUTION

The grille overlay may only be installed on indoor units.

1. Prepare your overlay using the dimensions provided in the

figure on page 15 for 24 inch models and page 16 for 15 inch

models. If using a hook and loop style mount, drill hole A will

not be used.

Area

Back

Front

Wood Overlay

Grille

15 Inch Models

2. If desired, stain and finish your grille to match your surrounding

decor. Follow the stain manufacturers instructions to apply stain

to your overlay.

Installation

NOTICE

The wood overlay grille must be installed in such a manner that the grille assembly can still be removed from the unit.

Screw Mount (Recommended)

1.Remove the grille from your unit by removing the two mounting screws. See below.

Remove Screw

Remove Screw

2.Lay the back of your grille overlay onto the front of the grille. Make certain the screw holes and vents are aligned.

3.Slide each of the screws removed in step 1 through the grille overlay and grille.

4.Mount your new overlay onto your unit by screwing the overlay back onto the base of your unit.

Application

 

Area

Wood Overlay

 

Back

Grille

Front

3.Carefully align the wood overlay with the grille and press into position.

14

u-line.com

Image 16
Contents Installation Guide Table of Contents General Precautions Safety Alert DefinitionsSafety Precautions Exterior Cleaning Product Registration Models CoveredTools / Material Required Inspect & PlanElectrical Specifications Cut-Out DimensionsPrepare Site SeriesProduct Dimensions 2115R Series 2115WC / 2115WCOL Series 21175RC/RCG/RF Series2175BEVC Series 2175WCC SeriesDoor Swing Dimensions Side-By-Side InstallationPower Supply Other Site RequirementsDoor Alignment and Adjustment To align and adjust the doorDoor Reversability Doors Self-ClosingReinstall hinge to bottom opposite Reversing Black or White DoorsRemove Door Remove hole plugsReversing Stainless Steel Glass Doors Pull Frame Away Push Glass Remove existing bottom hinge Wood Trim Finishing Staining and final finish applicationFinal finish-only application To insert a rack in the cabinetDoor Panel Installation Panel DimensionsDoor Panel Installation Custom 1/4 Thick Door Panel InsertInstallation Grille OverlayWood Grille Overlay PreparationGrille Overlay Dimensions 24 Inch Models Grille Overlay Dimensions 15 Inch Models Overlay Frame Frame Preparation2115WCOL 2175WCCOL & 2175BEVCOL Models Only Thickness of the overlay panel must be 3/4Prepare the New Overlay Panel Attaching the Overlay PanelAssembling Door to Cabinet Door closersInstallation InstallationInstallation Troubleshooting Leveling InformationDESIGNED, Engineered and Assembled in WISCONSIN, USA
Related manuals
Manual 28 pages 41.87 Kb