U-Line U-2175RCB-00 manual Door Alignment and Adjustment, Door Reversability, Doors Self-Closing

Page 9

6 Doors (Self-Closing)

Door Alignment and Adjustment

Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost may form in the interior.

NOTICE

Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to ensure that it is firmly in contact with the cabinet. Also make sure the door gasket is not pinched on the hinge side of the door.

The door will not be flush with the top of the cabinet. The top edge of the door will be 1/8 in. (3.175 mm) below the cabinet top.

1/8"

(3.175 mm)

To align and adjust the door:

1.Compare the top edge of the door (opposite the hinges) to the top edge of the cabinet and note the type (up or down) of adjustment needed.

1

2 3

1

2 3

2.Remove the top hinge pivot pin with a Phillips screwdriver and lift door off bottom hinge pin. Be careful not to lose the door closer insert sets.

3.Turn the door upside down and inspect the hinge plate mounting holes. The plate has slotted mounting holes. Loosen but do not remove the two hinge plate screws (1).

4.If door edge opposite the hinges needs to move up, move plate toward outside of door (2). If door edge needs to move down, move plate toward inside of door (3). Repeat until top edge of

4

door is parallel with top of cabinet and tighten screws (1) securely.

5.After adjustment is complete, remove the door closers from the bottom hinge, clean thoroughly and apply petroleum jelly to the mating surfaces of the closers. Be sure that pins on closers align with holes in the door and bottom cabinet hinge plates. Mount door and install top hinge pivot pin.

Door Reversability

Location of the unit may make it desirable to mount the door on the opposite side of the cabinet. Many doors are reversible. See table below.

Model

Reverse

Model

Reverse

 

 

 

 

U-2115RB-00

YES

U-2175WCCOL-02

YES

U-2115RS-00

NO

U-2175WCCOL-60

YES

U-2115RS-01

NO

U-2175WCCS-00

YES

U-2115RS-02

NO

U-2175WCCS-02

YES

U-2115RSOD-00

NO

U-2175WCCS-13

YES

U-2115RSOD-01

NO

U-2175WCCS-22

YES

U-2115RW-00

YES

U-CLR2160B-00

YES

U-2115WCOL-00

YES

U-CLR2160B-40

YES

U-2115WCS-00

YES

U-CLR2160S-00

NO

U-2175BEVCOL-00

YES

U-CLR2160S-01

NO

U-2175BEVCOL-02

YES

U-CLR21060S-40

NO

U-2175BEVCOL-60

YES

U-CLR2160S-41

NO

U-2175BEVCS-00

YES

U-CLR2160SOD-00

NO

U-2175BEVCS-02

YES

U-CLR2160SOD-01

NO

U-2175RCB-00

YES

U-CLR2160SOD-40

NO

U-2175RCB-02

YES

U-CLR2160SOD-41

NO

U-2175RCGOL-00

YES

U-CLR2160W-00

YES

U-2175RCGS-00

YES

U-CLR2160W-40

YES

U-2175RCS-00

NO

U-CLRCO2175B-00

YES

U-2175RCS-01

NO

U-CLRCO2175B-40

YES

U-2175RCS-22

NO

U-CLRCO3286S-00

NO

U-2175RCW-00

YES

U-CLRCO2175S-01

NO

U-2175RSOD-00

NO

U-CO2175FS-01

NO

U-2175RSOD-01

NO

U-CO2175FW-00

YES

U-2175WCCOL-00

YES

 

 

 

 

 

 

u-line.com

7

Image 9
Contents Installation Guide Table of Contents Safety Alert Definitions General PrecautionsSafety Precautions Product Registration Models Covered Exterior CleaningTools / Material Required Inspect & PlanCut-Out Dimensions Electrical SpecificationsPrepare Site Series2115R Series 2115WC / 2115WCOL Series 21175RC/RCG/RF Series Product Dimensions2175WCC Series 2175BEVC SeriesSide-By-Side Installation Door Swing DimensionsPower Supply Other Site RequirementsTo align and adjust the door Door Alignment and AdjustmentDoor Reversability Doors Self-ClosingReversing Black or White Doors Reinstall hinge to bottom oppositeRemove Door Remove hole plugsReversing Stainless Steel Glass Doors Pull Frame Away Push Glass Remove existing bottom hinge Staining and final finish application Wood Trim FinishingFinal finish-only application To insert a rack in the cabinetPanel Dimensions Door Panel InstallationDoor Panel Installation Custom 1/4 Thick Door Panel InsertGrille Overlay InstallationWood Grille Overlay PreparationGrille Overlay Dimensions 24 Inch Models Grille Overlay Dimensions 15 Inch Models Frame Preparation Overlay Frame2115WCOL 2175WCCOL & 2175BEVCOL Models Only Thickness of the overlay panel must be 3/4Attaching the Overlay Panel Prepare the New Overlay PanelDoor closers Assembling Door to CabinetInstallation InstallationInstallation Troubleshooting Leveling InformationDESIGNED, Engineered and Assembled in WISCONSIN, USA
Related manuals
Manual 28 pages 41.87 Kb