Smeg STA6249, STA6248 User instructions, DELAYED START BUTTON on some models only

Page 11

DELAYED START BUTTON (on some models only)

User instructions

DELAYED START BUTTON (on some models only)

8Pressing this button in sequence delays the start of the program by 3, 6 or 9 hours.

DELAYED START LIGHTS (on some models only)

9Illuminate to show that start delayed by 3, 6 or 9 hours has been set.

SETTING THE WASHING PROGRAM AND SWITCHING ON

To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling.

After using the table to identify the most appropriate washing program:

•press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate;

•keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desired program illuminates;

•close the door; after about 2" the program will start. While it is in progress, the relative LIGHT will flash (indicating that the program is being executed).

10

Image 11

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents NEVER BE REMOVED Safety instructions1. Safety and operating instructions USES OTHER THAN THOSE DESCRIBED ABOVETHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELS2.1 Water supply connection Installation instructions2. Installation and hook-up DRAIN CONNECTION CONNECTING TO THE WATER SUPPLYIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsNEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD FOR GREAT BRITAIN ONLY Fuse replacement3.1 Upper panel User instructions3. Description of the controls SELECTED PROGRAM INDICATOR LIGHTSDELAYED START LIGHTS on some models only SETTING THE WASHING PROGRAM AND SWITCHING ONDELAYED START BUTTON on some models only Only run the soak program with half loads The correct amount of detergent has been added to the dispenser 3.2 Washing programsBefore starting a washing program make sure that TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT CANCELLING THE CURRENT PROGRAMCHANGING THE PROGRAM TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES END OF CYCLE4.1 Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTCorrect loading of the dishes helps ensure optimal washing results 4.3 General warnings and recommendations3/1 Products Dishes and objects in copper, tin, zinc or brass these tend to stain LOADING THE LOWER BASKET 4.4 Using the basketsLOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETADJUSTING THE UPPER BASKET Version C with adjustment in three positions on both sides 5.1 General warnings and recommendations 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER CLEANING THE SPRAY ARMSFill the rinse aid dispenser Shut off the water supply tap CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE PROLONGED DISUSEReconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSEIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that E1 E2 E3 E4 E5 E6 6. TroubleshootingFAULT Safety levelWater intake system malfunction E7 E8 E9Turbine flow-regulator malfunction Alternate washing system malfunctionHeight depending on models Capacity Water supply pressure TECHNICAL DATAElectrical characteristics Width