Smeg STA6248, STA6249 User instructions, Before Starting The Dishwasher After Prolonged Disuse

Page 30

BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE:

User instructions

BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE:

•Check that there are no deposits of sludge or rust inside the water pipe: if there are, allow the water to run from the water supply tap for a few minutes.

•Plug the power cord back into the socket.

•Reconnect the water intake hose and open the tap again.

TROUBLESHOOTING MINOR PROBLEMS

In some cases it is possible to remedy minor problems by referring to the following instructions:

If the program fails to start, check that:

•the dishwasher is connected to the electrical power supply;

•there is no power failure;

•the water tap is open;

•the dishwasher door is properly closed.

If water remains inside the dishwasher, check that:

•the drain hose is not kinked;

•the drain siphon is not obstructed;

•the dishwasher filters are not clogged.

If the dishes are not being cleaned properly, check that:

•the correct amount of detergent has been added;

•there is regenerating salt inside the special container;

•the dishes are being loaded correctly;

•the selected program is suitable for the dish types and their degree of soiling;

•all the filters are clean and positioned correctly;

•the spray arm nozzles are not obstructed;

•there is no object obstructing the rotation of the spray arms.

29

Image 30

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCEInstallation instructions 2. Installation and hook-up2.1 Water supply connection CONNECTING TO THE WATER SUPPLY DRAIN CONNECTION2.2 Electrical connection and precautions NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD Fuse replacement FOR GREAT BRITAIN ONLYSELECTED PROGRAM INDICATOR LIGHTS User instructions3. Description of the controls 3.1 Upper panelSETTING THE WASHING PROGRAM AND SWITCHING ON DELAYED START BUTTON on some models onlyDELAYED START LIGHTS on some models only Only run the soak program with half loads 3.2 Washing programs Before starting a washing program make sure thatThe correct amount of detergent has been added to the dispenser TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT CANCELLING THE CURRENT PROGRAMCHANGING THE PROGRAM TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTEND OF CYCLE REMOVING THE DISHES4. Operating instructions 4.1 Using the water softening systemADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT During the washing cycle, the dispenser will be opened automatically4.3 General warnings and recommendations 3/1 ProductsCorrect loading of the dishes helps ensure optimal washing results Dishes and objects in copper, tin, zinc or brass these tend to stain 4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET UPPER BASKET LOADING THE UPPER BASKETADJUSTING THE UPPER BASKET Version C with adjustment in three positions on both sides CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1 General warnings and recommendationsPROLONGED DISUSE CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE Fill the rinse aid dispenser Shut off the water supply tapBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that Reconnect the water intake hose and open the tap againIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank Safety level 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6Alternate washing system malfunction E7 E8 E9Turbine flow-regulator malfunction Water intake system malfunctionWidth TECHNICAL DATAElectrical characteristics Height depending on models Capacity Water supply pressure