Smeg STA6248, STA6249 Installation instructions, Electrical connection and precautions

Page 8

2.2 Electrical connection and precautions

Installation instructions

2.2 Electrical connection and precautions

CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON THE INNER EDGE OF THE DOOR.

THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE REGULATIONS IN FORCE.

THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION.

NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD.

IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL SERVICE CENTRE.

DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID THE POSSIBILITY OF OVERHEATING OR BURNING.

IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD:

IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL-POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTACTS OF AT LEAST 3.5MM. AFTER INSTALLATION THE DISCONNECTION DEVICE HAS TO BE EASY TO REACH.

THE CONNECTION TO THE MAINS MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME SHOWN BELOW AND THE REGULATIONS IN FORCE.

L = brown N = blue

= yellow-green

In the event of damage to the supply cord, have it replaced by the manufacturer or an Authorized Technical Service Centre in order to avoid any risk.

7

Image 8

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents Safety instructions 1. Safety and operating instructionsUSES OTHER THAN THOSE DESCRIBED ABOVE NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCE2.1 Water supply connection Installation instructions2. Installation and hook-up CONNECTING TO THE WATER SUPPLY DRAIN CONNECTIONIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD 2.2 Electrical connection and precautionsNEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD Fuse replacement FOR GREAT BRITAIN ONLYUser instructions 3. Description of the controlsSELECTED PROGRAM INDICATOR LIGHTS 3.1 Upper panelDELAYED START LIGHTS on some models only SETTING THE WASHING PROGRAM AND SWITCHING ONDELAYED START BUTTON on some models only Only run the soak program with half loads The correct amount of detergent has been added to the dispenser 3.2 Washing programsBefore starting a washing program make sure that CANCELLING THE CURRENT PROGRAM CHANGING THE PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTEND OF CYCLE REMOVING THE DISHES4. Operating instructions 4.1 Using the water softening systemADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT During the washing cycle, the dispenser will be opened automaticallyCorrect loading of the dishes helps ensure optimal washing results 4.3 General warnings and recommendations3/1 Products Dishes and objects in copper, tin, zinc or brass these tend to stain LOADING THE LOWER BASKET 4.4 Using the basketsLOWER BASKET CUTLERY BASKET UPPER BASKET LOADING THE UPPER BASKETADJUSTING THE UPPER BASKET Version C with adjustment in three positions on both sides 5. Cleaning and maintenance CLEANING THE WATER INTAKE FILTERCLEANING THE SPRAY ARMS 5.1 General warnings and recommendationsCLEANING THE FILTER UNIT GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCEPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tapTROUBLESHOOTING MINOR PROBLEMS If the dishes are not being cleaned properly, check thatBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap againIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that 6. Troubleshooting FAULTSafety level E1 E2 E3 E4 E5 E6E7 E8 E9 Turbine flow-regulator malfunctionAlternate washing system malfunction Water intake system malfunctionTECHNICAL DATA Electrical characteristicsWidth Height depending on models Capacity Water supply pressure