Smeg STA6249, STA6248 instruction manual User instructions, End Of Cycle, Removing The Dishes

Page 15

END OF CYCLE

User instructions

If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program.

END OF CYCLE

At the end of the washing cycle the dishwasher gives a short acustic signal and the program indicators nr 4 and 5 start blinking (the word "end" is displayed on the window).

To switch off the dishwasher, open the door and press the ON/OFF button (1).

REMOVING THE DISHES

At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket.

14

Image 15

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents NEVER BE REMOVED Safety instructions1. Safety and operating instructions USES OTHER THAN THOSE DESCRIBED ABOVETHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELSInstallation instructions 2. Installation and hook-up2.1 Water supply connection DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY2.2 Electrical connection and precautions NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD FOR GREAT BRITAIN ONLY Fuse replacement3.1 Upper panel User instructions3. Description of the controls SELECTED PROGRAM INDICATOR LIGHTSSETTING THE WASHING PROGRAM AND SWITCHING ON DELAYED START BUTTON on some models onlyDELAYED START LIGHTS on some models only Only run the soak program with half loads 3.2 Washing programs Before starting a washing program make sure thatThe correct amount of detergent has been added to the dispenser TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT CANCELLING THE CURRENT PROGRAMCHANGING THE PROGRAM TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES END OF CYCLE4.1 Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENT4.3 General warnings and recommendations 3/1 ProductsCorrect loading of the dishes helps ensure optimal washing results Dishes and objects in copper, tin, zinc or brass these tend to stain 4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETADJUSTING THE UPPER BASKET Version C with adjustment in three positions on both sides 5.1 General warnings and recommendations 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER CLEANING THE SPRAY ARMSFill the rinse aid dispenser Shut off the water supply tap CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE PROLONGED DISUSEReconnect the water intake hose and open the tap again TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSEIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank E1 E2 E3 E4 E5 E6 6. TroubleshootingFAULT Safety levelWater intake system malfunction E7 E8 E9Turbine flow-regulator malfunction Alternate washing system malfunctionHeight depending on models Capacity Water supply pressure TECHNICAL DATAElectrical characteristics Width