Smeg LS19-7 User instructions, Washing programs, Before starting a washing program make sure that

Page 13

3.3 Washing programs

User instructions

3.3 Washing programs

The dishwasher is equipped with a control panel and an INFORMATION DISPLAY (8), described in chapter "1. Description of the controls", from which it is possible to carry out all the power switch-on, switch-off and programming operations.

Before starting a washing program make sure that:

•The water supply tap is open.

•The correct amount of detergent has been added to the dispenser.

•The baskets have been correctly loaded.

•The spray arms are able to rotate freely and without obstruction.

•The dishwasher door is securely closed.

CANCELLING THE CURRENT PROGRAM

To annul the current program, press the START/PAUSE button (3) for a few seconds, until the beep of confirmation is heard.

At this point, to end the program, press the HALF LOAD (5) and START/PAUSE (3) buttons simultaneously.

"P0" appears on the INFORMATION DISPLAY (8) and the dishwasher will automatically switch to the end of the cycle, displaying the word "End" when done.

CHANGING THE PROGRAM

To change the program, press and hold down the START/PAUSE button

(3)for a few seconds, then select the new program as described previously in the instructions; press the START/PAUSE button (3) again, holding it down for a few seconds.

12

Image 13

Contents Page Contents 1. Safety and operating instructions Safety instructionsTHIS DISHWASHER MUST BE USED BY ADULTS Safety instructionsAQUASTOP MODELS Safety instructions2. Installation and hook-up Installation instructionsFor free-standingmodels only CONNECTING TO THE WATER SUPPLY Installation instructions2.1 Water supply connection DRAIN CONNECTION2.2 Electrical connection and precautions Installation instructionsL = brown N = blue = yellow-green Fuse replacement Installation instructionsFOR GREAT BRITAIN ONLY 3. Description of the controls User instructionsSWITCHING ON 3.1 Front panelUser instructions SETTING THE WASHING PROGRAMNot present User instructions User instructions CANCELLING THE CURRENT PROGRAM3.3 Washing programs Before starting a washing program make sure thatUser instructions DELAYING THE PROGRAM available in all programs except the soak program User instructionsTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT User instructionsSTARTING THE DISHWASHER User instructionsEND OF CYCLE REMOVING THE DISHES4.1Using the water softening system 4. Operating instructionsUser instructions Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system User instructionsUser instructions 4.2 Using the rinse aid and detergent dispensersWATER HARDNESS TABLE User instructions ADJUSTING THE RINSE AID DISPENSER SETTINGADDING THE RINSE AID ADDING THE DETERGENT User instructions4.3 General warnings and recommendations User instructions3/1 Products Silverware silver items may stain User instructionsUser instructions 4.4 Using the basketsLOWER BASKET LOADING THE LOWER BASKET User instructionsLoading examples ½ LOAD CUTLERY BASKET User instructionsMovement required to extract the insertsUPPER BASKET User instructionsLOADING THE UPPER BASKET User instructions Depending on the models, the basket may be equipped with some or all of the following accessoriesUser instructions ADJUSTING THE UPPER BASKETVersion B User instructions CLEANING THE WATER INTAKE FILTER 5. Cleaning and maintenanceCLEANING THE SPRAY ARMS User instructionsUser instructions CLEANING THE FILTER UNITPROLONGED DISUSE Fill the rinse aid dispenserUser instructions TROUBLESHOOTING MINOR PROBLEMSIf the program fails to start, check that there is rinse aid inside the special container User instructionsFAULT 6. TroubleshootingUser instructions E1 E2 E3User instructions FAULTE5 E6 DESCRIPTION The dishwasher fails to draw waterdes ressortslateraux avant l’installation mollelaterali primadell’installazioneMontare la porta e regolarelatensione delle einstellen