True Manufacturing Company TDD-4, TD-50-18-S-LT Startup, Install Draft ARM, Light Switch Location

Page 11

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

BEER DISPENSERS CONTINUED...

INSTALL DRAFT ARM continued...

Insert air hose (one inch plastic tube) in draft arm, being careful not to disturb insulation. Remove top cover of draft arm and attach air hose clip to the insulating sleeve at the top of the draft arm. Replace top cover. The air hose clip will assure that the hose remains in proper place at all times, keeping the beer faucet cold. (See image 7-9)

7

8

9

STARTUP

Step 5

A.The compressor is ready to operate. Plug in the cooler.

B.Temperature control set at No. 4 position gives refrigerators an approximate temperature of 35°F and glass chiller frosters have an approximate temperature of 0°F. Allow unit to function several hours, completely cooling cabinet before changing the control setting.

C.Excessive tampering with the control could lead to service difficulties. Should it ever become necessary to replace temperature control, be sure it is ordered from your True dealer or recommended service agent.

D.Good air flow in your True unit is critical. Be careful to load product so that it neither presses against the back wall, nor comes within four inches of the evaporator housing. Refrigerated air off the coil must circulate down the back wall.

LIGHT SWITCH LOCATION:

The switch is located on the front of the evaporator housing toward the front of the cabinet. Open the front doors and the switch will be visible close to the ceiling the cabinet.

NOTE

If the unit is disconnected or shut off, wait five minutes before starting again.

RECOMMENDATION

Before loading product we recommend you run your True unit empty for two to three days. This allows you to be sure electrical wiring and installation are correct and no shipping damage has occurred. Remember, our factory warranty does not cover product loss!

REPLACEMENT PARTS

TRUE maintains a record of the cabinet serial number for your cooler. If at any time during the life of your cooler, a part is needed, you may obtain this part by furnishing the model number and serial number to the company from whom you purchased the cooler. Call Toll-Free: (800)-424-TRUE (Direct to Parts Department). (800)-325-6152 (U.S.A. & Canada only) or call: (636)- 240-2400.

9

www.truemfg.com

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents BAR Equipment Glass Chillers True Food Service Equipment, Inc Safety Precautions Refrigerant Disposal Proper Disposal of the RefrigeratorUSE of Extension Cords Before You Throw Away Your Old Refrigerator or FreezerNorth America Use Only HOW to Connect ElectricityStep Installation / Operation Instructions OwnershipRequired Tools UncratingTools Required LocatingLeveling Conductors and Circuits NSF Approved Sealants Sealing Cabinet to FloorPosition Cabinet Step Level CabinetNext Install Draft ARMElectrical Instructions Beer DispensersStartup Install Draft ARMLight Switch Location Replacement PartsStorage and Handling Shelf InstallationHorizontal Bottle Cooler BIN Divider Installation OperationTDD-1 CO2 KNOCK-OUT TemperaturePressure TappingBad Taste Draft Beer ProblemsDanfoss Temperature Control High Altitude Adjustment Only Temperature Control Adjustment for High Altitude onlyDont lay CO2 cylinders flat Dont drop CO2 cylinders Pressure Adjustment on CO2 RegulatorChanging CO2 GAS Cylinder Decreasing PressureCleaning Cleaning BAR SystemCleaning kit purchased from True follow these instructions Prepare SolutionStep MAINTENANCE, Care & Cleaning Cleaning the Condenser CoilSaturday 745 a.m. to 1145 a.m. CST Disconnect the electrical power to the unitRemove the louvered grill Stainless Steel Equipment Care and Cleaning Stainless Steel Equipment Care and Cleaning Light Bulb Replacement IDL Integrated Door Lighting Warranty Information U.S.A. and Canada only
Top Page Image Contents