Whirlpool Slide-In Electric Ranges Installation Requirements, Tools and Parts

Page 4

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

Tools needed

■Tape measure

■Flat-blade screwdriver

■Phillips screwdriver

■Level

■Hand or electric drill

■Hammer

■Wrench or pliers

■Pipe wrench

■¹⁵⁄₁₆" combination wrench

■³⁄₈" drive ratchet

■³⁄₈" nut driver

■¹⁄₈" (3.2 mm) drill bit (for wood floors)

■Marker or pencil

■Masking tape

■Pipe-joint compound resistant to LP gas

■³⁄₁₆" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

■Noncorrosive leak-detection solution

For LP/Natural Gas

Conversions

■½" combination wrench

■7 mm combination wrench

■7 mm nut driver

■Size T20 TORX®† screwdriver

clearances specified on the model/serial rating plate. The

model/serial rating plate is located on the oven frame behind

the storage drawer panel.

■ The range should be located for convenient use in the

kitchen.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

■ All openings in the wall or floor where range is to be installed

must be sealed.

■ Do not seal the range to the side cabinets.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The floor anti-tip bracket must be installed. To install the anti-

Parts supplied

Check that all parts are included.

A

B

C

D

A.Anti-tip bracket

B.Plastic anchors (2)

C.#10 x ¹⁄₂" screws (2)

D.Rear vent (for slide-in models)

■Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

tip bracket shipped with the range, see “Install Anti-Tip

Bracket” section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or ¼" (0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194° (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the current standards CAN/CSA-A240-latest edition, or with local codes.

Mobile home installations require:

■When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

†®TORX is a registered trademark of Textron Innovations Inc.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation Instructions 30 76.2 CM Freestanding and SLIDE-IN GAS RangesRange Safety Table of ContentsWhat to do if YOU Smell GAS Tools and Parts Installation RequirementsLocation Requirements Product Dimensions Freestanding Range Installation ClearancesSlide-in Range Freestanding and Slide-in RangesElectrical Requirements Type of GasNatural gas LP gas conversionGas Supply Pressure Testing Countertop PreparationGas Supply Line Gas Pressure RegulatorInstall Anti-Tip Bracket Unpack RangeInstall Rear Vent Level RangeVerify Anti-Tip Bracket Location Make Gas ConnectionTypical flexible connection Check OperationComplete Connection Adjust Flame Height Adjust Oven Bake Burner Flame if neededCheck Operation of Cooktop Burners Standard Surface Burners Three Flame BurnerComplete Installation Adjust Oven Broil Burner Flame if neededReplace Oven Racks & Storage or Warming Drawer Check Operation of Oven Broil BurnerGAS Conversions LP Gas ConversionTo Convert Gas Pressure Regulator Gas pressure regulatorTo Convert Standard Surface Burners To Convert Three Flame Burner on some modelsTo Convert Oven Bake Burner Natural Gas ConversionTo Convert Oven Broil Burner Stamped number Plate External gas orifice spud Internal gas orifice spud Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importanteExigences demplacement Exigences D’INSTALLATIONOutillage et pièces Cuisinière coulissante Dimensions du produit Cuisinière autoportanteDégagements de séparation à respecter Spécifications électriques Cuisinière autoportante et coulissanteType de gaz Spécifications de l’alimentation en gazCanalisation de gaz Préparation du plan de travail Instructions D’INSTALLATIONDéballage de la cuisinière Installation de la bride antibasculement Installation du raccord du conduit ’évacuation à l’arrière Vérification de lemplacement de la bride AntibasculementRaccordement à la canalisation de gaz Mise à niveau de la cuisinièreRaccordement typique par raccord flexible Compléter le raccordementContrôle du fonctionnement Brûleur à triple réglageRéglage de la taille des flammes Contrôle du fonctionnement du brûleur du fourContrôle du fonctionnement du brûleur du gril Achever l’installationSil est nécessaire de régler la taille des flammes Conversions Pour Changement DE GAZ Conversion pour lalimentation au propaneConversion du détendeur Si la cuisinière ne fonctionne pas, contrôler ce qui suitConversion des brûleurs standard de la table de cuisson DétendeurConversion du brûleur du four Conversion du brûleur du grilConversion pour lalimentation au gaz Naturel Chiffre gravé Conversion du brûleur du four Holes in bracket Trous dans la bride 9761413B

Slide-In Electric Ranges specifications

Whirlpool slide-in electric ranges are designed to bring convenience, style, and efficiency to the modern kitchen. These innovative appliances stand out not just for their aesthetics but also for their advanced features and technology that cater to a range of cooking needs.

One of the main characteristics of Whirlpool slide-in electric ranges is their seamless design. Unlike traditional freestanding models, slide-in ranges have a built-in appearance, fitting snugly between cabinets for a sophisticated look. This design eliminates the gap between the range and the countertop, preventing spills and crumbs from accumulating. Additionally, the front-control design places the controls at the front of the unit, allowing easy access and eliminating the need to reach over hot pots and pans.

Whirlpool electric ranges are equipped with powerful and precise cooking technologies. Many models feature advanced induction cooking options that provide rapid heating and consistent temperature control. Induction cooking utilizes electromagnetic energy to directly heat pots and pans, making it faster and more energy-efficient compared to traditional electric coils or radiant burners. For those who prefer traditional cooking, the ranges often come with smooth-top radiant elements, which provide a modern surface that is easy to clean.

In terms of oven features, Whirlpool slide-in electric ranges include convection cooking options, which circulate hot air throughout the oven for even baking and roasting. This technology ensures that food cooks consistently and eliminates the need for manual rotation. Additionally, many models offer self-cleaning options, making maintenance easier and freeing up time for users.

Another noteworthy feature is the FlexHeat Dual Radiant Element, offering flexibility in cooking. This element is equipped with both 6-inch and 9-inch zones, allowing cooks to match the size of their cookware with the burner size, optimizing energy use.

Connectivity is also a significant aspect of modern Whirlpool electric ranges. Many of their models are Wi-Fi-enabled, allowing users to control their ovens remotely using a smartphone. This means preheating the oven, adjusting cooking temperatures, and even setting timers can all be accomplished from anywhere in the home.

Whirlpool slide-in electric ranges combine functionality with stylish design, bringing energy-efficient cooking and advanced technology to kitchens. With features such as versatile cooking surfaces, advanced oven technology, and smart capabilities, these ranges are ideal for both seasoned chefs and home cooks alike. Whether you’re baking, broiling, or simmering, a Whirlpool slide-in electric range is designed to enhance culinary experiences while complementing any kitchen décor.
Top Page Image Contents