Whirlpool Slide-In Electric Ranges Level Range, Install Rear Vent, Make Gas Connection

Page 9

10.If installing the range in a mobile home, you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the “Location Requirements” section.

11.Continue installing your range using the following installation instructions.

Level Range

1.Place rack in oven.

2.Place level on rack and check levelness of the range, first side to side; then front to back.

Install Rear Vent

If you have a slide-in range, the rear vent must be installed.

Remove the outside screws from the rear trim on range. Use screws to attach rear vent to range.

Verify Anti-Tip Bracket Location

1.On models with a storage drawer, pull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remove drawer and set it aside on a covered surface.

On models with a warming drawer, the rear leg cannot be seen by removing the warming drawer. It will be necesary to view the rear foot from outside the range.

2.Making sure the anti-tip bracket is installed:

Look for the anti-tip bracket securely attached to floor.

Slide range back so rear range foot is under anti-tip bracket.

3.If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket.

On Ranges Equipped with Storage Drawers:

Use a wrench and pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

On Ranges Equipped with Warming Drawers:

Use pliers to adjust leveling legs up or down until the range is level. Push range back into position. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range to the existing gas line. Your connections may be different, according to the supply line type, size and location.

1.Apply pipe-joint compound made for use with LP gas to all pipe thread connections.

9

Image 9
Contents 30 76.2 CM Freestanding and SLIDE-IN GAS Ranges Installation InstructionsTable of Contents Range SafetyWhat to do if YOU Smell GAS Installation Requirements Tools and PartsLocation Requirements Installation Clearances Product Dimensions Freestanding RangeSlide-in Range Freestanding and Slide-in RangesType of Gas Electrical RequirementsNatural gas LP gas conversionCountertop Preparation Gas Supply Pressure TestingGas Supply Line Gas Pressure RegulatorUnpack Range Install Anti-Tip BracketLevel Range Install Rear VentVerify Anti-Tip Bracket Location Make Gas ConnectionCheck Operation Typical flexible connectionComplete Connection Adjust Oven Bake Burner Flame if needed Adjust Flame HeightCheck Operation of Cooktop Burners Standard Surface Burners Three Flame BurnerAdjust Oven Broil Burner Flame if needed Complete InstallationReplace Oven Racks & Storage or Warming Drawer Check Operation of Oven Broil BurnerLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator Gas pressure regulatorTo Convert Three Flame Burner on some models To Convert Standard Surface BurnersNatural Gas Conversion To Convert Oven Bake BurnerTo Convert Oven Broil Burner Stamped number Plate External gas orifice spud Internal gas orifice spud Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreExigences D’INSTALLATION Exigences demplacementOutillage et pièces Dimensions du produit Cuisinière autoportante Cuisinière coulissanteDégagements de séparation à respecter Cuisinière autoportante et coulissante Spécifications électriquesSpécifications de l’alimentation en gaz Type de gazCanalisation de gaz Instructions D’INSTALLATION Préparation du plan de travailDéballage de la cuisinière Installation de la bride antibasculement Vérification de lemplacement de la bride Antibasculement Installation du raccord du conduit ’évacuation à l’arrièreRaccordement à la canalisation de gaz Mise à niveau de la cuisinièreCompléter le raccordement Raccordement typique par raccord flexibleBrûleur à triple réglage Contrôle du fonctionnementRéglage de la taille des flammes Contrôle du fonctionnement du brûleur du fourAchever l’installation Contrôle du fonctionnement du brûleur du grilSil est nécessaire de régler la taille des flammes Conversion pour lalimentation au propane Conversions Pour Changement DE GAZConversion du détendeur Si la cuisinière ne fonctionne pas, contrôler ce qui suitDétendeur Conversion des brûleurs standard de la table de cuissonConversion du brûleur du gril Conversion du brûleur du fourConversion pour lalimentation au gaz Naturel Chiffre gravé Conversion du brûleur du four Holes in bracket Trous dans la bride 9761413B

Slide-In Electric Ranges specifications

Whirlpool slide-in electric ranges are designed to bring convenience, style, and efficiency to the modern kitchen. These innovative appliances stand out not just for their aesthetics but also for their advanced features and technology that cater to a range of cooking needs.

One of the main characteristics of Whirlpool slide-in electric ranges is their seamless design. Unlike traditional freestanding models, slide-in ranges have a built-in appearance, fitting snugly between cabinets for a sophisticated look. This design eliminates the gap between the range and the countertop, preventing spills and crumbs from accumulating. Additionally, the front-control design places the controls at the front of the unit, allowing easy access and eliminating the need to reach over hot pots and pans.

Whirlpool electric ranges are equipped with powerful and precise cooking technologies. Many models feature advanced induction cooking options that provide rapid heating and consistent temperature control. Induction cooking utilizes electromagnetic energy to directly heat pots and pans, making it faster and more energy-efficient compared to traditional electric coils or radiant burners. For those who prefer traditional cooking, the ranges often come with smooth-top radiant elements, which provide a modern surface that is easy to clean.

In terms of oven features, Whirlpool slide-in electric ranges include convection cooking options, which circulate hot air throughout the oven for even baking and roasting. This technology ensures that food cooks consistently and eliminates the need for manual rotation. Additionally, many models offer self-cleaning options, making maintenance easier and freeing up time for users.

Another noteworthy feature is the FlexHeat Dual Radiant Element, offering flexibility in cooking. This element is equipped with both 6-inch and 9-inch zones, allowing cooks to match the size of their cookware with the burner size, optimizing energy use.

Connectivity is also a significant aspect of modern Whirlpool electric ranges. Many of their models are Wi-Fi-enabled, allowing users to control their ovens remotely using a smartphone. This means preheating the oven, adjusting cooking temperatures, and even setting timers can all be accomplished from anywhere in the home.

Whirlpool slide-in electric ranges combine functionality with stylish design, bringing energy-efficient cooking and advanced technology to kitchens. With features such as versatile cooking surfaces, advanced oven technology, and smart capabilities, these ranges are ideal for both seasoned chefs and home cooks alike. Whether you’re baking, broiling, or simmering, a Whirlpool slide-in electric range is designed to enhance culinary experiences while complementing any kitchen décor.