Aiwa XR-H33MD user service Precautions, Owners record, Installation, Electric Power

Page 2

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Owner's record

For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.

Model No.

Serial No. (Lot No.)

CX-NH33MD

 

SX-NH33

 

 

 

PRECAUTIONS

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.

Installation

1 Water and moisture - Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the like

2 Heat - Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate heat. It also should not be placed in temperatures less than 5ºC (41ºF) or greater than 35 Cº(95ºF).

3 Mounting Surface - Place the unit on a flat, even surface

4 Ventilation - The unit should be situated with adequate space around it so that proper heat ventilation is assured. Allow 10 cm (4 in.) clearance from the rear and then tope of the unit, and 5 cm (2 in.) from each side.

-Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.

-Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

5 Objects and liquid entry - Take care that objects of liquids do not get inside the unit through the ventilation openings.

6 Carts and stands - When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

7 Condensation - Moisture may form on the CD pickup lens when:

-The unit is moved from a cold spot to a warm spot

-The heating system has just been turned on

-The unit is used in a very humid room

-The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few hours, then try to operate again.

8 Wall or ceiling mounting - The unit should not be mounted on a wall or ceiling, unless specified in the Operating Instructions

Electric Power

1 Power sources - Connect this unit only to power sources specified in the Operating Instructions, and as marked on the unit.

2 Polarization - As a safety feature, some units are equipped with polarized AC power plugs which can only be inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to

Page 1 Page 3
Image 2
Page 1 Page 3
Contents XR-H33MD English pgElectric Power PrecautionsInstallation Owners recordTable of Contents Radio Reception Preparations Check your system and accessoriesBefore connecting the AC cord ConnectionsConnect the supplied antennas Connect the AC cord to an AC outletTo use Shift on the remote control Remote ControlWhen to replace batteries To use Function on the remote controlBefore Operation Sound Audio AdjustmentsVolume Super T-BASS SystemManual Tuning Radio ReceptionPresetting Stations To clear a preset station Preset Number TuningSelecting a preset number on the main unit Repeat steps 1Basic Operations To select a reverse mode deck 2 onlyTape Playback Press Button to start playContinuous Play When tapes are loaded in both decksTo start play when the power is off Direct Play Function To set the tape counter toAbout cassette tapes To play all discs in the disc compartment, press Loading DiscsPlaying Discs RANDOM/REPEAT Play Programmed Play Press the RANDOM/REPEAT button repeatedlyTo change the programmed tracks To clear the programTo add tracks to the program To play the programmed tracks repeatedlyPress To check the track title To select a track with the remote controlTo play a disc at double speed To check the disc titlePage Basic Recording Select the reverse modeTape Recording Preparation Use Type I normal tapes onlyInserting Blank Spaces Dubbing a Tape ManuallyDubbing the Whole Tape Insert the tape into deck AI Edit RecordingPress the Sync DUB button to start recording To check the order of the programmed track numbers To stop the recordingTo clear the edit program To add tracks from other discs to the edit programProgrammed Edit Recording Press zTAPE REC/REC Mute button to start recording MD RecordingRecording a Whole CD To stop recordingDisplay information during recording Registering index marks automaticallyTo record on a previously recorded MD Recording only ONE Track of aAuto First Tracks Recording CDS Programmed Recording of CDS Recording Three CDS CONTINUOUSLYzTo add index marks during recording Within 10 seconds, press the Enter button Press zMD RECPress the to start recording Recording levelWithin 10 seconds, press the Enter button Press the Mode buttonRecording from a TAPE, Radio or Connected Equipment To prevent accidental erasure of recorded material Extended Recording MonauralPress the zMD REC button Press Mode three times Optical discs Extended Timer RecordingType of MD Recordable MO*1 discsUltra compact size made possible by ATRAC*2 technology Quick random accessLimitations of MD Track numbers may not be registered properlyRegistering the Disc Title Enter a letter, number or symbolRegistering the Disc Title Track Title Registering the Track Titles Dividing a Track Press MD Edit repeatedly until Divide is displayed Within 10 seconds, press EnterIf the tracks are titled Combining TWO TracksPress MD Edit repeatedly until Combine is displayed Changing the Order Tracks Erasing a Single Track Erasing TracksErasing ALL Tracks on a Disc Within 1 minute, press the Enter button againClock and Timer Setting the ClockIf the clock display flashes Setting the TimerTo switch to the 24-hour standard PreparationSetting the Timer Recording Setting the Sleep Timer VIDEO/AUX Jacks Connecting Optional EquipmentOther Connections CD Digital OUT /MD Digital OUT Optical JacksTo Play Equipment Connected to the VIDEO/AUX Jacks Digital in Optical JackListening to External Sources General Care and MaintenanceTo Play Equipment Connected to the Digital in Jack Care of MDs SpecificationsCare of tapes Main unit CX-NH33MDSpeaker system SX-NH33 Troubleshooting Guide Tuner SectionMD Recorder Section Cassette Deck SectionCD Player Section To reset Parts Index
Top Page Image Contents