Aiwa XR-H33MD user service Troubleshooting Guide, Tuner Section

Page 56

Specifications and external appearance are subject to change without notice.

• US AND FOREIGN PATENTS LICENSED FROM DOLBY LABORATORIES LICENSING CORPORATION.

COPYRIGHT

Please check the laws on copyright relating to recordings from discs, radio or external tape for the country in which the machine is being used.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Modifications or adjustments to this product, which are not expressly approved by the manufacturer, may void the user's right or authority to operate this product.


	GENERAL (cont)	pg.35

TROUBLESHOOTING GUIDE

If the unit fails to perform as described in these Operating Instructions, check the following guide.

GENERAL

There is no sound.

•Is the AC cord connected properly?

•Is there a bad connection? ( → page 3)

•There may be a short circuit in the speaker term inals.

→Disconnect the AC cord, then correct the speaker connections.

• Was an incorrect function button pressed?

Sound is emitted from one speaker only.

• Is the other speaker disconnected?

An erroneous display or a malfunction occurs.

→Reset the unit as stated below.

TUNER SECTION

There is constant, wave-like static.

•Is the antenna connected properly? (- page 4)

•Is the signal weak?

Image 56

Contents XR-H33MD English pgPrecautions InstallationElectric Power Owners recordTable of Contents Radio Reception Check your system and accessories Before connecting the AC cordPreparations ConnectionsConnect the supplied antennas Connect the AC cord to an AC outletRemote Control When to replace batteriesTo use Shift on the remote control To use Function on the remote controlBefore Operation Audio Adjustments VolumeSound Super T-BASS SystemManual Tuning Radio ReceptionPresetting Stations Preset Number Tuning Selecting a preset number on the main unitTo clear a preset station Repeat steps 1To select a reverse mode deck 2 only Tape PlaybackBasic Operations Press Button to start playWhen tapes are loaded in both decks To start play when the power is off Direct Play FunctionContinuous Play To set the tape counter toAbout cassette tapes To play all discs in the disc compartment, press Loading DiscsPlaying Discs RANDOM/REPEAT Play Programmed Play Press the RANDOM/REPEAT button repeatedlyTo clear the program To add tracks to the programTo change the programmed tracks To play the programmed tracks repeatedlyPress To select a track with the remote control To play a disc at double speedTo check the track title To check the disc titlePage Select the reverse mode Tape RecordingBasic Recording Preparation Use Type I normal tapes onlyInserting Blank Spaces Dubbing a Tape ManuallyDubbing the Whole Tape Insert the tape into deck AI Edit RecordingPress the Sync DUB button to start recording To stop the recording To clear the edit programTo check the order of the programmed track numbers To add tracks from other discs to the edit programProgrammed Edit Recording MD Recording Recording a Whole CDPress zTAPE REC/REC Mute button to start recording To stop recordingDisplay information during recording Registering index marks automaticallyTo record on a previously recorded MD Recording only ONE Track of aAuto First Tracks Recording CDS Programmed Recording of CDS Recording Three CDS CONTINUOUSLYzWithin 10 seconds, press the Enter button Press zMD REC Press the to start recordingTo add index marks during recording Recording levelWithin 10 seconds, press the Enter button Press the Mode buttonRecording from a TAPE, Radio or Connected Equipment To prevent accidental erasure of recorded material Extended Recording MonauralPress the zMD REC button Press Mode three times Extended Timer Recording Type of MDOptical discs Recordable MO*1 discsQuick random access Limitations of MDUltra compact size made possible by ATRAC*2 technology Track numbers may not be registered properlyRegistering the Disc Title Enter a letter, number or symbolRegistering the Disc Title Track Title Registering the Track Titles Dividing a Track Press MD Edit repeatedly until Divide is displayed Within 10 seconds, press EnterIf the tracks are titled Combining TWO TracksPress MD Edit repeatedly until Combine is displayed Changing the Order Tracks Erasing Tracks Erasing ALL Tracks on a DiscErasing a Single Track Within 1 minute, press the Enter button againClock and Timer Setting the ClockSetting the Timer To switch to the 24-hour standardIf the clock display flashes PreparationSetting the Timer Recording Setting the Sleep Timer Connecting Optional Equipment Other ConnectionsVIDEO/AUX Jacks CD Digital OUT /MD Digital OUT Optical JacksTo Play Equipment Connected to the VIDEO/AUX Jacks Digital in Optical JackListening to External Sources General Care and MaintenanceTo Play Equipment Connected to the Digital in Jack Specifications Care of tapesCare of MDs Main unit CX-NH33MDSpeaker system SX-NH33 Troubleshooting Guide Tuner SectionMD Recorder Section Cassette Deck SectionCD Player Section To reset Parts Index