DCS BGB36-BQAR manual Leak Testing, General, Before Testing, To Test

Page 13

LEAK TESTING

GENERAL:

Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

Before Testing:

Do not smoke while leak testing. Extinguish all open flames. Never leak test with an open flame. Make a soap solution of one part liquid detergent and one part water. You will need a spray bottle, brush, or rag to apply the solution to the fittings. For LP units, check with a full cylinder. The valve panel must be removed to check the valves and fittings. Remove the knobs and the safety valve knob, then remove the 2 screws which fasten the valve panel to the unit (you will need a Philips head for this). Pull the valve panel outward and unplug the wires from the ignition module and the back of the ignition button. Remove the screws which hold the service panel in place. Remove the service panel.

To Test:

Make sure all control valves are in the “OFF” position. Turn the gas supply “ON”. Check all connections from the supply line, or LP cylinder up to and including the manifold pipe assembly. Apply the soap solution around the connection, valve, tubing and end of the manifold. Soap bubbles will appear where a leak is present. If a leak is present, immediately turn off gas supply, tighten any leaking connections, turn gas on, and recheck. Check all the gas connections at the base of the control valves where they screw into the manifold pipe.

To check rotis burner and safety valve the burner must be lit, then leak test the connections located behind the service panel. If you cannot stop a gas leak turn off the gas supply and call your local gas utility, or the dealer you purchased the appliance from. Only those parts recommended by the manufacturer should be used on the Grill. Substitution can void the warranty.

Do not use the grill until all connections have been checked and do not leak.

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy water near the shut-off valve of the gas supply valve. Spray all the fittings. Bubbles indicate leaks. (Fig. 05 & 06)

Bottom of unit

LEAK TEST POINTS

CHECK HOSE FOR

SIGNS OF ABRASIONS,

CRACKS, OR LEAKS

LP TANK

Bottom of unit

LEAK TEST POINTS

FIG.05 LP Gas

FIG.06 Nat. Gas

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Professional 36/48 BGB Grill Please Retain this Manual for Future Reference Message to OUR CustomersTable of Contents Important Safety Notice Safety Practices & PrecautionsGrill Placement Safety Practices & Precautions Grill Models Total GAS Consumption of the Grill with ALL Burners on HI GAS RequirementsNatural GAS Hook UP To HOOK-UP the Fittings Supplied with the GrillLP Tank Requirements LP GAS Hook UP Type 1 or QCC1 RegulatorInsulated Jacket Locating GRILL/BUILT-IN ClearancesLocation Clearances to Combustible ConstructionGeneral Standard layout for non-combustible enclosure BUILT-IN Construction DetailsBefore Testing Leak TestingGeneral To TestInstaller Final Checklist Installer CHECKLIST/BURNER AdjustmentsGrill Burner Flame Height Side Burner Flame HeightGrill Burner Air Adjustment Burner AdjustmentsTo Adjust LOW Setting AdjustmentsRadiant Asssembly Installation Using the GrillGrill Important Using the Grill Replacement of Regulators and HoseGrilling Hints To Light the Grill Burner Using the GRILL/LIGHTING InstructionsMatch Lighting To Light Dual Side Burners 48BQR Models only Lighting InstructionsSide Burners Lighting Instructions Side Burners Match LightingTo Light the Smoker Burner Using the Smoker SystemWood Chips ROD Light Motor Preparation Using the RotisserieRecommended Working AreaCooking on Rotisserie Manual Lighting To Light the Rotisserie BurnerCare and Cleaning Grill burner cleaning Burner Removal and CleaningSide Burners IgnitersSmoker Burner Orifice CleaningBefore Calling for Service TroubleshootingGrill won’t light when the ignition button is pushed Low heat with knob in HI positionDescription BGB36/48-BQAR Grill Body Parts ListBGB48-BQR Grill Body Parts List BGB48-BQR Grill Body Parts List BGB36-BQAR, BGB48-BQR Handle, Rotisserie Rod 18040 Screw Rotisserie AssemblySmoker Burner Assembly Grill Cart Parts List 33032-01 Wiring Diagram BGB36-BQAR Models Wiring Diagram BGB48-BQR Models Smoker Burner Electrode Wiring Diagram BGB48-BQAR ModelsHOW to Obtain Service ServiceLength of Warranty WarrantyDCS Will Pay For DCS Will Not Pay ForLitho in USA 09/2001

BGB36-BQAR specifications

The DCS BGB36-BQAR is a premium built-in gas barbecue grill that flawlessly combines functionality with sophisticated design, offering grilling enthusiasts an unparalleled cooking experience. This grill is tailored for those who are serious about outdoor cooking, providing innovative features that elevate the grilling process to a new level.

One of the standout characteristics of the DCS BGB36-BQAR is its powerful heating capabilities. Equipped with four high-performance burners that produce an impressive total of 60,000 BTUs, this grill ensures quick heat-up times and optimal temperature control. Each burner is designed to deliver consistent flame distribution, allowing for precise cooking temperatures across the grilling surface.

The grill boasts a spacious cooking area of 726 square inches, making it ideal for entertaining and preparing meals for large gatherings. The cooking surface comprises heavy-duty stainless steel grates that provide excellent heat retention and easy cleaning properties. These grates are designed to leave beautiful sear marks on meats, enhancing presentation and flavor profiles.

In addition to the main grilling surface, the DCS BGB36-BQAR features a convenient infrared rotisserie burner, perfect for slow-roasting meats to perfection. This technology ensures even heat distribution, producing juicy, flavorful dishes every time. The built-in rotisserie kit allows cooks to easily prepare whole chickens or roasts with minimal effort.

Another prominent technology incorporated in this grill is the ceramic ignition system, which ensures reliable start-up every time. This feature eliminates the frustration of dealing with traditional ignition systems and provides peace of mind while grilling. Combined with the grill's robust construction, which includes a double-lined hood for heat retention and longevity, the DCS BGB36-BQAR is built to last.

User convenience is further enhanced by the integrated grease management system, which collects drippings and minimizes flare-ups. It also features built-in LED lights that illuminate the cooking surface, allowing users to grill comfortably even in low-light conditions.

In summary, the DCS BGB36-BQAR is an exceptional grill that marries cutting-edge technology with thoughtful design elements. With its high BTU output, generous cooking space, advanced ignition system, and thoughtful features like the rotisserie burner and grease management, it caters to both novice and experienced grilling aficionados, making outdoor cooking a truly enjoyable experience.
Top Page Image Contents