Whirlpool GI15NDXZQ, GI15NDXZS, GI15NDXZB manual Interior Components

Page 15

4.Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

A

A. Condenser fins

5.Replace the lower access panel using the 4 screws.

6.Plug in ice maker or reconnect power.

Interior Components

1.Unplug ice maker or disconnect power.

2.Open the storage bin door and remove any ice that is in the bin.

3.Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4.Pull out on the bottom of the cutter grid cover until the snaps release to remove.

5.Unplug the wiring harness from the left side of the cutter grid.

A

A. Cutter grid cover

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7.Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

 

D

A

 

B

E

C

F

 

A. Cutter grid harness

D. Ice level sensor harness

B. Screw

E. Plastic spacer

C. Cutter grid

F. Screw

8.Remove the mounting screw that holds the water pan in place. Pull out on the front of the water pan.

9.Disconnect the pump bracket from the water pan and unplug the water pan drain pump.

A

 

B

D

C

 

A. Water pan

C. Drain cap

B. Water pan screw

D. Drain pump cover

10.Remove, clean and replace the ice scoop and ice scoop holder.

NOTE: On some models, the ice scoop holder is located in the upper left of the unit, and on other models, the ice scoop holder is located in the lower left of the unit.

■After removing the ice scoop, remove the holder by removing the 2 screws.

■Wash the ice scoop holder along with the other interior components using the following instructions.

■Replace the ice scoop holder by replacing the screws.

A

B

A.Screws

B.Ice scoop holder

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents W10518926B ICE MakerTable of Contents ÍndiceTable DES Matières Unpack the Ice Maker ICE Maker SafetyInstallation Instructions Cleaning Before UseRecommended Grounding Method Location RequirementsElectrical Requirements Water Supply RequirementsTools Needed Rear View Connecting the Water LineVacation or Extended Time Without Use Connect Water SupplyDrain Cap Ice Maker Drain Pump InstallationIf Ice Maker Is Currently Installed Kit ContainsDrain Tube Drain Pump InstallationDrain Pump Installed Rear PanelDrain Connection Vent TubeGravity Drain System Drain Pump System on some models Connecting the DrainIce Maker Door Reversal Side Swing Only Side ViewReplace Door Wrap on some models Door Stop and End-Cap ReversalReverse Hinges Replace DoorReverse Door Catch Install the Water FilterLeveling Water Filtration SystemReplace the Water Filter ICE Maker USEHow Your Ice Maker Works Water Filter Status LightDoor Ajar Alarm Using the ControlsFast Ice Mode CleanIce Maker System CleaningICE Maker Care Exterior SurfacesInterior Components For Ice Makers with a Drain Pump Installed Vacation and Moving CareTo Shut Down the Ice Maker Ice Maker Seems Noisy TroubleshootingIce Maker Operation Ice Maker Will Not OperateIce Production Ice QualityIce Maker Runs But Produces No Ice Our consultants provide assistance with If you need replacement partsU.S.A CanadaAccessories Performance Data SheetThis limited warranty does not cover Whirlpool Corporation Major Appliance WarrantySu seguridad y la seguridad de los demás es muy importante Seguridad DE LA Fábrica DE HieloRequisitos eléctricos Instrucciones DE InstalaciónDesempaque la fábrica de hielo Requisitos de ubicaciónRequisitos del suministro de agua Vacaciones o tiempo prolongado Sin usoConexión del suministro de agua Instalación de la bomba de desagüe de La fábrica de hielo Vista posteriorEl juego contiene Instalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Ubicaciones de las piezasVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadConexión del desagüe Sistema de la bomba de desagüe en algunos modelosInversión de las bisagras Cómo volver a colocar la puertaBisagra superior Nivelación Bisagra inferiorCómo invertir el seguro de la puerta Instalación del filtro de agua Sistema de filtración de aguaUSO DE LA Fábrica DE Hielo Cómo funciona su fábrica de hieloUso de los controles Cuidado DE LA Fábrica DE Hielo Sonidos normalesLimpieza Bandeja de agua Tapón de desagüe Condensador Un condensador sucio u obstruidoTornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasSolución DE Problemas Funcionamiento de la fábrica de hieloLa fábrica de hielo no funciona Producción de hielo Calidad del hieloLa fábrica de hielo funciona pero no produce hielo Problemas de plomería Ayuda O Servicio TécnicoEn los EE.UU Limpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaEsta garantía limitada no cubre Garantía LimitadaVotre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsEnlèvement des matériaux d’emballage Instructions D’INSTALLATIONExigences d’emplacement Déballage de la machine à glaçonsRaccordement à la canalisation d’eau Spécifications électriquesSpécifications de l’alimentation en eau Vacances ou longue période ’inutilisationOutillage nécessaire Raccordement du tuyau d’eauVue arrière Bouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Contenu de l’ensemblePosition des pièces Panneau arrièreTube de vidange Encoche de patte de montage de la pompe de vidangeTube de ventilation Pompe de vidange installéeSystème avec pompe de vidange sur certains modèles Raccordement de vidangeVidange par gravité Vue latéraleClé de ¹⁄₄ Tournevis Phillips Charnière inférieure Réinstallation de la porteRéinstallation du revêtement de porte sur certains modèles Inversion du sens de montage des charnièresInstaller le filtre à eau NivellementSystème de filtration d’eau Témoin lumineux de l’état du filtre à eau Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsBruits normaux Utilisation des commandesMode Fast Ice glaçons rapides Alarme de porte entrouverteSystème de la machine à glaçons Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresComposants intérieurs Précautions à prendre avant les vacances ou un déménagement Arrêt de la machine à glaçonsMachine à glaçons avec pompe de vidange La machine à glaçons ne fonctionne pas DépannageQualité des glaçons Production de glaçonsSi vous avez besoin de pièces de rechange Assistance OU ServiceProblèmes de plomberie Aux États-UnisAu Canada AccessoiresSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceGarantie DES Gros Appareils Ménagers Whirlpool Corporation La présente garantie limitée ne couvre pasW10518926B

GI15NDXZS, GI15NDXZQ, GI15NDXZB specifications

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS are versatile and stylish ice makers designed to enhance any kitchen or home bar area. These models stand out for their sleek design, compact size, and user-friendly features, making them ideal for those looking to enjoy the luxury of freshly-made ice at home.

One of the main features of these models is their production capacity. Each unit can produce up to 35 pounds of ice per day, ensuring that you never run out, whether you're hosting a party or enjoying a quiet evening at home. The ice maker uses a state-of-the-art compressor cooling system which not only supports efficient production but also helps maintain consistent ice quality. The bin capacity is also impressive, accommodating up to 28 pounds of ice, meaning less frequent refills and more convenience for users.

In terms of design, these models boast a modern stainless steel exterior, with finishes available in bold black, classic white, and sleek stainless steel. This variety allows for easy integration into any kitchen decor or style. The reversible door feature adds flexibility in placement, making it easy to fit the unit in different spaces.

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS also integrate innovative technologies that enhance functionality. One such technology is the advanced filtration system that improves water quality, ensuring that the ice produced is crystal clear and tastes great. The units are designed with a quiet operation feature, making them suitable for any environment, including open-concept spaces or entertainment areas.

Moreover, these models include an automatic shutoff feature that activates when the ice bin is full, preventing overflow and minimizing waste. They also have a simple control panel that allows users to easily turn the machine on and off, as well as monitor the ice production status.

Maintenance is straightforward, with a removable ice bin that simplifies cleaning and filling. The interior surfaces are designed for easy wipe-down, helping to maintain hygiene with minimal effort.

In summary, the Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS ice makers combine efficiency, style, and convenience. With their robust ice production capabilities, modern aesthetics, and user-friendly features, these units make a valuable addition to any home, enabling users to enjoy cold drinks and ice in a hassle-free manner.
Top Page Image Contents