Whirlpool GI15NDXZS, GI15NDXZQ Drain Pump Installation, Rear Panel, Drain Tube, Parts Locations

Page 7

Drain Pump Installation

NOTE: Do not kink, smash or damage tubes or wires during installation.

1.Unplug ice maker or disconnect power.

2.Remove rear panel. See “Rear Panel” illustration for 5 screw locations. Pull rear panel away from the drain tube and discard.

Rear Panel

A

A

A. Screw locations

3.Remove the old drain tube and clamp attached to the ice maker bin.

NOTE: Discard old drain tube and clamp.

4.Install new drain tube (⁵⁄₈" ID x 5¹⁄₈") from ice maker bin to drain pump reservoir inlet using new adjustable clamps. See “Drain Tube” illustration.

NOTES:

■Do not kink.

■Trim tube length, if required.

Drain Tube

 

A

 

B

 

C

 

D

A. ⁷⁄₈" adjustable hose clamp

C. ⁷⁄₈" adjustable hose clamp

B. Drain tube (ice bin to drain pump)

D. Drain pump reservoir inlet

5.Install vent tube (⁵⁄₁₆" ID x 32" [81 cm]) to drain pump reservoir vent. Use one ⁵⁄₈" small adjustable clamp, supplied. See “Parts Locations” illustration.

NOTE: Do not install household drain tube at this time.

Parts Locations

A

B

C

D

E

G

F

A. Vent tube

E. Ice maker unit power cord

B. ⁵⁄₈" hose clamp

F. #8-32 x ³⁄₈" pump mounting screws

C. Drain pump discharge tube

G. Drain pump power cord, clamp

D. Drain pump

and screw

6.Remove power cord clamp and ground screw attached to ice maker power cord, which is mounted to the unit base. See “Parts Locations” illustration.

NOTE: Clamp and screw will be reused.

7.Slide drain pump into the ice maker base on the right side. The pump mounting tab should slip into the rectangular slot in the ice maker base. It will be necessary to tip the pump slightly to slip into the slot. See “Drain Pump Mounting Tab Slot” illustration.

Drain Pump Mounting Tab Slot

A

A. Mounting tab slot

Drain Pump Installed

A

A. Drain pump installed

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents W10518926B ICE MakerÍndice Table of ContentsTable DES Matières Unpack the Ice Maker ICE Maker SafetyInstallation Instructions Cleaning Before UseRecommended Grounding Method Location RequirementsElectrical Requirements Water Supply RequirementsTools Needed Rear View Connecting the Water LineVacation or Extended Time Without Use Connect Water SupplyDrain Cap Ice Maker Drain Pump InstallationIf Ice Maker Is Currently Installed Kit ContainsDrain Tube Drain Pump InstallationDrain Pump Installed Rear PanelVent Tube Drain ConnectionGravity Drain System Drain Pump System on some models Connecting the DrainIce Maker Door Reversal Side Swing Only Side ViewReplace Door Wrap on some models Door Stop and End-Cap ReversalReverse Hinges Replace DoorReverse Door Catch Install the Water FilterLeveling Water Filtration SystemReplace the Water Filter ICE Maker USEHow Your Ice Maker Works Water Filter Status LightDoor Ajar Alarm Using the ControlsFast Ice Mode CleanIce Maker System CleaningICE Maker Care Exterior SurfacesInterior Components Vacation and Moving Care For Ice Makers with a Drain Pump InstalledTo Shut Down the Ice Maker Ice Maker Seems Noisy TroubleshootingIce Maker Operation Ice Maker Will Not OperateIce Quality Ice ProductionIce Maker Runs But Produces No Ice Our consultants provide assistance with If you need replacement partsU.S.A CanadaAccessories Performance Data SheetThis limited warranty does not cover Whirlpool Corporation Major Appliance WarrantySu seguridad y la seguridad de los demás es muy importante Seguridad DE LA Fábrica DE HieloRequisitos eléctricos Instrucciones DE InstalaciónDesempaque la fábrica de hielo Requisitos de ubicaciónVacaciones o tiempo prolongado Sin uso Requisitos del suministro de aguaConexión del suministro de agua Vista posterior Instalación de la bomba de desagüe de La fábrica de hieloEl juego contiene Instalación de la bomba de desagüe Si la fábrica de hielo ya está instaladaTapa de desagüe Línea de suministro de aguaBomba de desagüe instalada Tubo de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Ubicaciones de las piezasVista lateral Conexión del desagüeTubo de ventilación Sistema de desagüe por gravedadConexión del desagüe Sistema de la bomba de desagüe en algunos modelosCómo volver a colocar la puerta Inversión de las bisagrasBisagra superior Bisagra inferior NivelaciónCómo invertir el seguro de la puerta Instalación del filtro de agua Sistema de filtración de aguaCómo funciona su fábrica de hielo USO DE LA Fábrica DE HieloUso de los controles Sonidos normales Cuidado DE LA Fábrica DE HieloLimpieza Bandeja de agua Tapón de desagüe Condensador Un condensador sucio u obstruidoTornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasFuncionamiento de la fábrica de hielo Solución DE ProblemasLa fábrica de hielo no funciona Calidad del hielo Producción de hieloLa fábrica de hielo funciona pero no produce hielo Ayuda O Servicio Técnico Problemas de plomeríaEn los EE.UU Limpiador Hoja DE Datos DEL RendimientoAccesorios Filtro de aguaEsta garantía limitada no cubre Garantía LimitadaVotre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsEnlèvement des matériaux d’emballage Instructions D’INSTALLATIONExigences d’emplacement Déballage de la machine à glaçonsRaccordement à la canalisation d’eau Spécifications électriquesSpécifications de l’alimentation en eau Vacances ou longue période ’inutilisationRaccordement du tuyau d’eau Outillage nécessaireVue arrière Bouchon de vidange Si la machine à glaçons est installéeInstallation de la pompe de vidange Contenu de l’ensemblePosition des pièces Panneau arrièreTube de vidange Encoche de patte de montage de la pompe de vidangeTube de ventilation Pompe de vidange installéeSystème avec pompe de vidange sur certains modèles Raccordement de vidangeVidange par gravité Vue latéraleClé de ¹⁄₄ Tournevis Phillips Charnière inférieure Réinstallation de la porteRéinstallation du revêtement de porte sur certains modèles Inversion du sens de montage des charnièresNivellement Installer le filtre à eauSystème de filtration d’eau Témoin lumineux de l’état du filtre à eau Remplacement du filtre à eauUtilisation DE LA Machine À Glaçons Fonctionnement de la machine à glaçonsBruits normaux Utilisation des commandesMode Fast Ice glaçons rapides Alarme de porte entrouverteSystème de la machine à glaçons Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresComposants intérieurs Arrêt de la machine à glaçons Précautions à prendre avant les vacances ou un déménagementMachine à glaçons avec pompe de vidange La machine à glaçons ne fonctionne pas DépannageQualité des glaçons Production de glaçonsSi vous avez besoin de pièces de rechange Assistance OU ServiceProblèmes de plomberie Aux États-UnisAu Canada AccessoiresSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceLa présente garantie limitée ne couvre pas Garantie DES Gros Appareils Ménagers Whirlpool CorporationW10518926B

GI15NDXZS, GI15NDXZQ, GI15NDXZB specifications

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS are versatile and stylish ice makers designed to enhance any kitchen or home bar area. These models stand out for their sleek design, compact size, and user-friendly features, making them ideal for those looking to enjoy the luxury of freshly-made ice at home.

One of the main features of these models is their production capacity. Each unit can produce up to 35 pounds of ice per day, ensuring that you never run out, whether you're hosting a party or enjoying a quiet evening at home. The ice maker uses a state-of-the-art compressor cooling system which not only supports efficient production but also helps maintain consistent ice quality. The bin capacity is also impressive, accommodating up to 28 pounds of ice, meaning less frequent refills and more convenience for users.

In terms of design, these models boast a modern stainless steel exterior, with finishes available in bold black, classic white, and sleek stainless steel. This variety allows for easy integration into any kitchen decor or style. The reversible door feature adds flexibility in placement, making it easy to fit the unit in different spaces.

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS also integrate innovative technologies that enhance functionality. One such technology is the advanced filtration system that improves water quality, ensuring that the ice produced is crystal clear and tastes great. The units are designed with a quiet operation feature, making them suitable for any environment, including open-concept spaces or entertainment areas.

Moreover, these models include an automatic shutoff feature that activates when the ice bin is full, preventing overflow and minimizing waste. They also have a simple control panel that allows users to easily turn the machine on and off, as well as monitor the ice production status.

Maintenance is straightforward, with a removable ice bin that simplifies cleaning and filling. The interior surfaces are designed for easy wipe-down, helping to maintain hygiene with minimal effort.

In summary, the Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS ice makers combine efficiency, style, and convenience. With their robust ice production capabilities, modern aesthetics, and user-friendly features, these units make a valuable addition to any home, enabling users to enjoy cold drinks and ice in a hassle-free manner.
Top Page Image Contents