Whirlpool GI15NDXZB Vacation or Extended Time Without Use, Connect Water Supply, Tools Needed

Page 5

■The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the ice maker needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of water per hour to the ice maker for proper ice maker operation. If a reverse osmosis system is desired, only a whole-house capacity reverse osmosis system, capable of maintaining the steady water supply required by the ice maker, is recommended. Faucet capacity reverse osmosis systems are not able to maintain the steady water supply required by the ice maker.

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Vacation or Extended Time

Without Use

■When you will not be using the ice maker for an extended period of time, turn off the water and power supply to the ice maker.

■Check that the water supply lines are insulated against freezing conditions. Ice formations in the supply lines can increase water pressure and cause damage to your ice maker or home. Damage from freezing is not covered by the warranty.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances.

■Use copper tubing or Whirlpool supply line, Part Number 8212547RP, and check for leaks.

■Install tubing only in areas where temperatures will remain above freezing.

Tools Needed

Gather the required tools and parts before starting installation:

■Flat-blade screwdriver

■⁷⁄₁₆" and ¹⁄₂" open-end wrenches or two adjustable wrenches

■¹⁄₄" nut driver

NOTE: Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

A

B

A.Bulb

B.Nut

3.Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply.

■Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

A

B

C

A. Compression sleeve

C. Copper tubing

B. Compression nut

4.Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe.

IMPORTANT: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction.

5.Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service.

Rear View

A

B

Connecting the Water Line

1.Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

2. Using a ¹⁄₂" copper supply line with a quarter-turn shutoff

C

valve or the equivalent, connect the ice maker as shown.

 

NOTE: To allow sufficient water flow to the ice maker a

 

minimum ¹⁄₂" diameter home supply line is recommended.

C. Inlet water tube clamp and

A. Copper tubing

B. Water supply tube clamp

supply line connector

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents W10518926B ICE MakerTable DES Matières Table of ContentsÍndice Installation Instructions ICE Maker SafetyCleaning Before Use Unpack the Ice MakerElectrical Requirements Location RequirementsWater Supply Requirements Recommended Grounding MethodVacation or Extended Time Without Use Rear View Connecting the Water LineConnect Water Supply Tools NeededIf Ice Maker Is Currently Installed Ice Maker Drain Pump InstallationKit Contains Drain CapDrain Pump Installed Drain Pump InstallationRear Panel Drain TubeGravity Drain System Drain ConnectionVent Tube Ice Maker Door Reversal Side Swing Only Connecting the DrainSide View Drain Pump System on some modelsReverse Hinges Door Stop and End-Cap ReversalReplace Door Replace Door Wrap on some modelsLeveling Install the Water FilterWater Filtration System Reverse Door CatchHow Your Ice Maker Works ICE Maker USEWater Filter Status Light Replace the Water FilterFast Ice Mode Using the ControlsClean Door Ajar AlarmICE Maker Care CleaningExterior Surfaces Ice Maker SystemInterior Components To Shut Down the Ice Maker For Ice Makers with a Drain Pump InstalledVacation and Moving Care Ice Maker Operation TroubleshootingIce Maker Will Not Operate Ice Maker Seems NoisyIce Maker Runs But Produces No Ice Ice ProductionIce Quality U.S.A If you need replacement partsCanada Our consultants provide assistance withAccessories Performance Data SheetThis limited warranty does not cover Whirlpool Corporation Major Appliance WarrantySu seguridad y la seguridad de los demás es muy importante Seguridad DE LA Fábrica DE HieloDesempaque la fábrica de hielo Instrucciones DE InstalaciónRequisitos de ubicación Requisitos eléctricosConexión del suministro de agua Requisitos del suministro de aguaVacaciones o tiempo prolongado Sin uso El juego contiene Instalación de la bomba de desagüe de La fábrica de hieloVista posterior Tapa de desagüe Si la fábrica de hielo ya está instaladaLínea de suministro de agua Instalación de la bomba de desagüeRanura de la lengüeta de montaje de la bomba de desagüe Tubo de desagüeUbicaciones de las piezas Bomba de desagüe instaladaTubo de ventilación Conexión del desagüeSistema de desagüe por gravedad Vista lateralConexión del desagüe Sistema de la bomba de desagüe en algunos modelosBisagra superior Inversión de las bisagrasCómo volver a colocar la puerta Cómo invertir el seguro de la puerta NivelaciónBisagra inferior Instalación del filtro de agua Sistema de filtración de aguaUso de los controles USO DE LA Fábrica DE HieloCómo funciona su fábrica de hielo Limpieza Cuidado DE LA Fábrica DE HieloSonidos normales Bandeja de agua Tapón de desagüe Condensador Un condensador sucio u obstruidoTornillo Espaciador de plástico Rejilla de corte Componentes interioresPara apagar la fábrica de hielo Cuidado durante las vacaciones y mudanzasLa fábrica de hielo no funciona Solución DE ProblemasFuncionamiento de la fábrica de hielo La fábrica de hielo funciona pero no produce hielo Producción de hieloCalidad del hielo En los EE.UU Problemas de plomeríaAyuda O Servicio Técnico Accesorios Hoja DE Datos DEL RendimientoFiltro de agua LimpiadorEsta garantía limitada no cubre Garantía LimitadaVotre sécurité et celle des autres est très importante Sécurité DE LA Machine À GlaçonsExigences d’emplacement Instructions D’INSTALLATIONDéballage de la machine à glaçons Enlèvement des matériaux d’emballageSpécifications de l’alimentation en eau Spécifications électriquesVacances ou longue période ’inutilisation Raccordement à la canalisation d’eauVue arrière Outillage nécessaireRaccordement du tuyau d’eau Installation de la pompe de vidange Si la machine à glaçons est installéeContenu de l’ensemble Bouchon de vidangeTube de vidange Panneau arrièreEncoche de patte de montage de la pompe de vidange Position des piècesTube de ventilation Pompe de vidange installéeVidange par gravité Raccordement de vidangeVue latérale Système avec pompe de vidange sur certains modèlesClé de ¹⁄₄ Tournevis Phillips Réinstallation du revêtement de porte sur certains modèles Réinstallation de la porteInversion du sens de montage des charnières Charnière inférieureSystème de filtration d’eau Installer le filtre à eauNivellement Utilisation DE LA Machine À Glaçons Remplacement du filtre à eauFonctionnement de la machine à glaçons Témoin lumineux de l’état du filtre à eauMode Fast Ice glaçons rapides Utilisation des commandesAlarme de porte entrouverte Bruits normauxNettoyage Entretien DE LA Machine À GlaçonsSurfaces extérieures Système de la machine à glaçonsComposants intérieurs Machine à glaçons avec pompe de vidange Précautions à prendre avant les vacances ou un déménagementArrêt de la machine à glaçons La machine à glaçons ne fonctionne pas DépannageQualité des glaçons Production de glaçonsProblèmes de plomberie Assistance OU ServiceAux États-Unis Si vous avez besoin de pièces de rechangeAu Canada AccessoiresSystème de filtration d’eau de la machine à glaçons Feuille DE Données SUR LA PerformanceW10518926B Garantie DES Gros Appareils Ménagers Whirlpool CorporationLa présente garantie limitée ne couvre pas

GI15NDXZS, GI15NDXZQ, GI15NDXZB specifications

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS are versatile and stylish ice makers designed to enhance any kitchen or home bar area. These models stand out for their sleek design, compact size, and user-friendly features, making them ideal for those looking to enjoy the luxury of freshly-made ice at home.

One of the main features of these models is their production capacity. Each unit can produce up to 35 pounds of ice per day, ensuring that you never run out, whether you're hosting a party or enjoying a quiet evening at home. The ice maker uses a state-of-the-art compressor cooling system which not only supports efficient production but also helps maintain consistent ice quality. The bin capacity is also impressive, accommodating up to 28 pounds of ice, meaning less frequent refills and more convenience for users.

In terms of design, these models boast a modern stainless steel exterior, with finishes available in bold black, classic white, and sleek stainless steel. This variety allows for easy integration into any kitchen decor or style. The reversible door feature adds flexibility in placement, making it easy to fit the unit in different spaces.

The Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS also integrate innovative technologies that enhance functionality. One such technology is the advanced filtration system that improves water quality, ensuring that the ice produced is crystal clear and tastes great. The units are designed with a quiet operation feature, making them suitable for any environment, including open-concept spaces or entertainment areas.

Moreover, these models include an automatic shutoff feature that activates when the ice bin is full, preventing overflow and minimizing waste. They also have a simple control panel that allows users to easily turn the machine on and off, as well as monitor the ice production status.

Maintenance is straightforward, with a removable ice bin that simplifies cleaning and filling. The interior surfaces are designed for easy wipe-down, helping to maintain hygiene with minimal effort.

In summary, the Whirlpool GI15NDXZB, GI15NDXZQ, and GI15NDXZS ice makers combine efficiency, style, and convenience. With their robust ice production capabilities, modern aesthetics, and user-friendly features, these units make a valuable addition to any home, enabling users to enjoy cold drinks and ice in a hassle-free manner.
Top Page Image Contents